Question about Kenmore 659 Electric Dryer

1 Answer

How to fix the door switch - Kenmore 659 Electric Dryer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Master
  • 2,223 Answers

Is the switch bad or did the cheesy sheet metal just bend a bit so the switch isn't being activated?

Posted on Dec 15, 2013

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HI... HOW TO FIX CANON ADV IR4235 E000840?


E840 is an error detection to the fixing inlet home position sensor.

PS63 (Fixing Inlet sensor) and PS66 (Fixing Inlet HP sensor)

may be caused by a poor connection on the front door switch. Try inspecting & re-seating the connection at the front door open/close switch=
++ make sure the front door is not vibrating away from the front door open/close switch (MSW7).
The door Magnet Action Catch may not properly be holding the door closed.



++ if paper is stuck in unit 1 frame side connector you might get a E840. If no paper is found in the connector check the connector for damage or cracks. Frame side connector assembly (FM2-5091-000).
https://www.instantprintersupport.com/canon-printer-support

Jul 16, 2018 | Canon imageCLASS Office Equipment &...

2 Answers

How do I know the door switch is bad


If light stays on when fully closed, door switch needs replacement, easily removed. Short term fix, disconnect the switch and tape the two spades together. Warning! Dryer will run even with door open.

Nov 29, 2014 | Sears Kenmore Elite Electric Dryer 69278

1 Answer

Fix a GE Profile PFWS4600 that will not start?


Hi, I think you are right about the door switch. You may have a bad switch. If that doesn't fix it the board maybe at fault. Replace the door switch first. Good luck.

Oct 21, 2014 | GE Washing Machines

2 Answers

E2 problem?how can i fix it?i have reset my washing and it doenst fix anything?


it appears when its going to spin the dryer :) THANKS NEED RESPONSE ASAP

Oct 14, 2014 | Washing Machines

1 Answer

Were the buzer locate


You do not need to fix the "buzzer". You need to fix the door switch or the circuit to the door switch.

May 17, 2012 | 1991 Mercury Capri

2 Answers

Disconnect sliding door chime 2005 Saturne Relay


On my 05 Relay I scratched the oxidation off of the switch heads and the contact plates on the door pillar. Worked for me.
Another fix I've read about is to take out and put back the PSD fuse. Then open and close the doors twice (with power button) for the computer to relearn the positions.

Feb 12, 2010 | 2005 Saturn Relay

1 Answer

My cars inside lights doesnt work when i open the door? or turn it off


have you checked the all the doors? if the fault is only with 1 door look for the "push" switch in the frame of the door, tp fix remove switch and earth lead going to switch, that should fix it, if all doors the feed to light from doors is defective check for a bad contact in light switch on unit, there should be 3 positions
  • one position fully off
  • 2nd position turn on manualy ( this over rides the door functions)
  • 3rd position door activation mode

Jan 03, 2010 | 2002 Honda Accord

3 Answers

2003 lincoln navigator running board stay out on passanger side unless your are moving (they retract) passenger mirror does not adjust backig up message continues saying door ajar


The door switches are built in the latches on each of the doors, they are pron to sticking, leaving the security module to beleive the door is open.
The simple fix is to spray a generous amount of WD40 on, in, and around the door latches, then opening and closing the door a few times. I would start with the passenger door as`this is likely the culprit. do the rest of the latches as a prevenitive measure.

Hope this is of some help.
Ed

Apr 20, 2009 | Lincoln Navigator Cars & Trucks

3 Answers

Will not spin Maytag PAV2300AWW top loader


check your door switch. Many times a faulty door switch can prevent the spin cycle. When you locate the door switch, take a jumper wire across the connection and advance the timer to spin. If it spins with the jumper wire, you will need a new door switch.

Jul 04, 2008 | Maytag Atlantis MAV6451 Top Load Washer

Not finding what you are looking for?
Kenmore 659 Electric Dryer Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Ned Halaweh
Ned Halaweh

Level 2 Expert

240 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...