Question about Copystar Office Equipment & Supplies

Open Question

Sharp error ng8000

Tried to scan a file but it didn' t send now lost original of file and no copy

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
professor_sc

Mark Lou Surmeon

  • 180 Answers

SOURCE: Scanning and Copying problem.

This is a hardware problem. I would suggest that you would replace the printer.

Posted on Aug 11, 2008

Ad

Anonymous

  • 564 Answers

SOURCE: dell 1815dn

hmmm..would that error be SMTP, by chance?


Posted on Aug 19, 2008

Anonymous

  • 115 Answers

SOURCE: Network Error on display

If you’re getting this on both machines, it is your network...
There a few possibilities...

1. SMTP / DNS Info. Is that correct? Your It can help with this?
go to the Nic page of the machine (IP Address in win explorer) , go to admin page, which the pass word should be sharp , look for the network settings. look at both the smtp info and the gateway and dns info.. Verify that it is correct.

2. Have you changed your Internet Service Provider?
For example, Comcast is making a habit of blocking port 25. Embarq DNS information is a mess, their mail relay is a real hassle.

3. E Mail server information changed? Does your server require authentication, is the Time out set correctly?

Posting the correct codes really help in resolving these issues
Below are a few of the codes...


CE 01 The network card is not installed or broken

CE 02 the specified mail server is server is not found.

CE 03 The specified server suspends response during Transmission of images.

Posted on Oct 23, 2008

frankzjm

Frank Zhang

  • 191 Answers

SOURCE: originals are sharp & clear; copies are gray

there are 2 reason:
1) the toner you are using now may not compatible well with the orignal cartridge unit.
2) the cartridge unit near the life-cycle, cause too much toner carry on the paper through the image printing.
you may try to change the quality toner, or change new cartridge if it over life-cycle

Posted on Jan 23, 2009

Anonymous

  • 1 Answer

SOURCE: Sharp AR-M450 can't scan to e-mail

Check your primary and secondary dns entry.Also a return admin address is required.
Regards Ed

Posted on Apr 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to store documents from computer to ricoh 3035?


When the machine is printing a
document stored using the copier
function, wait until printing has
finished before you store a document
in the Document Server.
A Press the {Document Server} key.
B Press [Scan Original].
C Enter a file name, user name, or
password if necessary.
Note
- If you do not enter a file name,
one is automatically assigned.
Reference
p.41 "To register or change the
user name"
p.41 "To change the file name"
p.42 "To set or change the password"
D Place originals either on the exposure
glass or in the ADF.
Reference
For information about types of
originals and how to place
them, see Copy Reference.
E Make any required settings.
Reference
For details, see Copy Reference.
F Press the {Start} key.
The document is stored in the Document
Server.
Note
- To stop scanning, press the
{Clear/Stop} key. To restart a
paused scanning job, press [Continue]
in the confirmation display.
To delete saved images
and cancel the job, press [Stop].
-When a password is set, appears
on the left side of the file
name.
- After scanning, stored documents
appear on the Select Files
to Print display. If this display
does not appear, press [Scanning
Finished].
- When placing an original on the
exposure glass, press [Scanning
Finished] after all the originals
have been scanned

To register or change the user name
A Press [Scan Original].
The Scan Original display appears.
B Press [User Name].
If user names are already registered,
the Change User Name display
appears. To use an
unregistered user name, press
[Non-programmed Name].
When no user name are registered
in the Address Book, the User
(Destination) Name entry display
appears.
When using a registered user
name in the Address Book
ASelect a registered user name
from the list, and then press
[OK].
To change your user name to an
unregistered user name, proceed
to the next step.
Reference
p.76 "Registering a New
User Code"
When using an unregistered user
name in the Address Book
ATo enter an unregistered user
name, press [Non-programmed
Name].
BEnter a new user name, and
then press [OK].
Reference
p.161 "Entering Text"
When no user name has been
registered in the Address Book
AEnter a new user name, and
then press [OK].
Reference
p.161 "Entering Text"
To change the file name
A Press [Scan Original].
The Scan Original display appears.
B Press [File Name].
The Change File Name display appears.
C Press [Delete All] to delete the old
file name.
Note
- You can also use [Backspace] to
delete unnecessary characters.


D Enter a new file name, and then
press [OK].
Note
- Up to 20 characters can be entered
as a file name. Note that
only 15 characters of each file
name appear in the document
list.
Reference
p.161 "Entering Text"
To set or change the password
A Press [Scan Original].
The Scan Original display appears.
B Press [Password].
C Enter a password using the
number keys (four-to eight-digits),
and then press the {#} key.
D Reenter the password (four-to
eight-digits) for verification, and
then press the {#} key.
E Press [OK].

May 22, 2014 | Ricoh Aficio 3045, 3035 Kit

1 Answer

How to make darker copies


if your referring to photocopying but printout is darker, it doesnt work. canon copiers produce copies like the original or better than the original sometimes. try to scan the file in custom mode and adjust the brightness and contrast and click preview to view the outcome before scanning it then print it later

Sep 30, 2013 | Canon PIXMA MP210 Photo All-In-One Printer

1 Answer

U162 error on black ink cannon printer


This error occurs when printer fails detecting ink level or printer assume that no ink in the cartridge. We cannot use print, copy,scan, and fax function before the problem fixed. It's recommended for you to replace ink cartridge. To continue using the printer without replacing the cartridge we must deactivate ink level detection function. Be aware that printing in this condition can damage the printer while sending fax or scan is not problem.


If you need any technical help on printer then you can reach at http://www.vtechsquad.com/

This error occurs when printer fails detecting ink level or printer assume that no ink in the cartridge. We cannot use print, copy,scan, and fax function before the problem fixed. It's recommended for you to replace ink cartridge. To continue using the printer without replacing the cartridge we must deactivate ink level detection function. Be aware that printing in this condition can damage the printer while sending fax or scan is not problem.

This error occurs when printer fails detecting ink level or printer assume that no ink in the cartridge. We cannot use print, copy,scan, and fax function before the problem fixed. It's recommended for you to replace ink cartridge. To continue using the printer without replacing the cartridge we must deactivate ink level detection function. Be aware that printing in this condition can damage the printer while sending fax or scan is not problem.

Original source: http://ij-forum.blogspot.com/2008/12/error-message-check-ink-u162u163.html#ixzz2Cpr4Be1K

This error occurs when printer fails detecting ink level or printer assume that no ink in the cartridge. We cannot use print, copy,scan, and fax function before the problem fixed. It's recommended for you to replace ink cartridge. To continue using the printer without replacing the cartridge we must deactivate ink level detection function. Be aware that printing in this condition can damage the printer while sending fax or scan is not problem.

Original source: http://ij-forum.blogspot.com/2008/12/error-message-check-ink-u162u163.html#ixzz2Cpr4Be1K

Nov 20, 2012 | Canon PIXMA MX340 Wireless Office...

1 Answer

I plugged my cruzer into my home computer to get some music files. I copied them on, then disconnected the drive from my home computer. I went to put them onto my mac, and when I copied them over, i...


I assume by you saying you didn't get any memory back that it still has the files on them or it looks that way. Now when you copied them did you just drag them over? When you go back to the thumb driver or the files still on there? usually when you copy all you are doing is just that copying you are not removing the files from the original source. If you copy them and then you would like to delete them just access the thumb drive again and then delete the files and you should get the space back.
thank you,
Lee

Aug 22, 2011 | SanDisk Cruzer Micro 4GB USB 2.0 Flash...

2 Answers

How do I scan a double sided copy on the Sharp 2300 N?


Put your paper in the document feeder. On the LCD screen touch the button that says 2 Sided. Then touch the one that says 2 to 2.

Aug 19, 2011 | Sharp MX-2300N Color Copier

1 Answer

My brother MFC 8500 is receiving alright but everything I send out has a big black streak going down the right side of the page. Confirmation page also has big black streak.


Let me see if I got this right.

The received fax is clean but when you send one out it has a black streak on it.
Cool! So far so good.
Makes sense because for sending, the fax scans the original document and parts of the scanning area could be dirty and so on. Therefore a black streak may appear.
The same black streak would also appear when you make a copy, because the original document must also be scanned.
Logical!

However for receiving faxes, the machine uses the internal memory and the print engine only, and the same applies to printing the transaction report, which comes from inside via the print engine.
The scanner has no rol in either situation.

Now I'm lost!

.

May 31, 2011 | Brother Office Equipment & Supplies

1 Answer

I can't get my HP potosmart C6180 ALL IN ONE PRINTER TO SCAN/COPY OR FAX WITHOUT GETTING A SCANNER FAILURE MESSAGE SAYING UNABLE TO SCAN,COPY OR SEND A FAX


Solved! I now can scan wirelessly throughout my network. I downloaded the drivers for a friends newer HP all-in-one scanner and I can scan. Look for the driver for the 309a series of printers and install it. Complete the install and set up your existing printer. You can now scan, print, fax wirelessly. It includes updated HP apps for these functions that work with OS 10.5. I didn't upgrade to the HP 1.1 drivers through Apple. The file name is: PS_AIO_05_C309a_Net_Full_Mac_WW_102.dmg

May 24, 2011 | HP Photosmart C6180 All-In-One InkJet...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

876 people viewed this question

Ask a Question

Usually answered in minutes!

Top Copystar Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Tammie Duggan
Tammie Duggan

Level 2 Expert

57 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you a Copystar Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...