Question about Whirlpool 24 in. ADP5966 Free-standing Dishwasher

Open Question

Having F8 fault code on my bauknecht dish washer

Hi,
my bauknecht dish washer shows F8 fault code continuously, I tried holding the start button, the fault code disappears, the washer starts again then after few seconds it stops, this only shows for washing on the higher degree ( 50-75), tried cleaning the down parts of the strain and filter, but also get the same result. Please help.

Thanks

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 87 Answers

SOURCE: F7 error

Raise your water supply temerature. Next open door and within 3 seconds hit hi-temp scrub, then energy saver. Do this again. Close door and latch, then push reset button.

Posted on Jun 10, 2007

Ad

Anonymous

  • 148 Answers

SOURCE: Whirlpool inbuil dishwasher

likely a logic board.
the fact that it goes from start to finish without any 'event' suggests that the board is bad.
good luck
mark

Posted on Dec 28, 2007

Anonymous

  • 14 Answers

SOURCE: whirlpool adp5962

you may have water in the base due to a leak internally.if you tilt the dishwasher backwards and water runs out.thats the cause of the problem.on all the whirlpool full size dishwashers .access to the base is through two t25 torx screws securing the base plate.

Posted on Dec 29, 2007

Anonymous

  • 46 Answers

SOURCE: Whirlpool dishwasher, flashing start button

you have a door suitch proble may sure the door is totaly close try that good luck

Posted on Sep 07, 2009

jsrock516

Jeff Rockwell

  • 5911 Answers

SOURCE: clean light keeps blinking

The blinking clean light is an interruption in the dishwasher program that usually indicates a component malfunction. It can also be a result of a momentary program glitch as well. If a component is defective, it's most commonly attributed to a heating cycle or thermostat failure. The following link explains how you may be able to clear the blinking clean light problem and possibly avoid a service call:

http://www.fixya.com/support/r3575752-dishwasher_blinking_clean_light

Keep in mind all dishwashers are not alike and have different panel options. If you do not have the same set up that I have mentioned, the tech sheet for your dishwasher will explain the touch pad functions. The tech sheet is located behind the lower toe panel under the door and lists the proper sequence of buttons to push for diagnostics and troubleshooting. Just remove the screws that hold the panel in place and remove.

NOTE: Sometimes the tech sheet is located behind the inner door panel. You will need to remove the screws securing the inner panel to access it if this is the case. Make sure you turn off the main power breaker before doing so.

In many cases, I found this to be a momentary glitch in operation. If the problem keeps reoccuring the number of flashes is an indication of WHICH circuit is causing your problem. As all dishwashers differ in operation and features, refer to your tech sheet for the recommended troubleshooting steps.

NOTE: Some dishwashers use the Sani-Rinse/Air Dry combination, some use the Sani-Rinse/Heated Dry combination. Some use a sequence of three, others use a sequence of 5 pushes of the buttons. If the tech sheet is not located behind the lower toe panel, it should be affixed somewhere under the dishwasher. I have also found them located inside the inner door panel. Let me know if you still need assistance.

Posted on Mar 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stuck in demonstration mode


Hi,

Turn the Machine OFF. Then, Press and Hold the Start Button and ON/OFF Button at the same time for few Seconds and it would fix the issue.

Let me know, if problem persists, with Make and Model of the Washer.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Jan 10, 2010 | Bauknecht Dishwashers

1 Answer

Hi, on my WAE8987 Washing machine, the fault code 'F07' keeps coming up, can anyone help please? thanks


Bauknecht are built by Whirlpool.
F7 on Whirlpool means flow meter failure.
Check water inlet, check the pressure switch, and check the sump filter at the bottom of the dishwasher.
To reset try turning on the power and holding the start button and the + and - buttons at the same time.

Dec 01, 2009 | Bauknecht Dishwashers

1 Answer

The dishwasher has been running for 3 hours and seems to be stuck on 1 minute left. Upon opening, there was sudsy water remaining in the bottom, but the dishes looked clean. The washer just won't go to...


SHU 53 MODELS To start test program, press and hold both SCRUB WASH and DELICATE/ECONO program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ ?21? = version 1 with jumper). When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button. To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone). Cycle Countdown display will show ?88″ when REGULAR WASH button is pressed and ?8h? when Delay Start button is pressed. To start testing, press both the SCRUB WASH and DELICATE/ECONO buttons a second time. When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ ?6? = faults 2 + 4). 0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault 1 = Aqua Sensor (?Sensotronic?) fault 4 = Filling fault F = Filling fault (display occurs during wash, not test) To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty. If water level switch (f1) has failed (opened), display will show fault code ?4″ and unit will continually fill and drain where testing won?t be completed. If flow switch (e5) has failed (opened), display will show ?0″, water won?t heat (to 150?F) and water won?t stop circulating. If NTC probe (f2/f4) has failed (opened), display will show fault code ?8″ immediately and testing will end shortly after water has started circulating.

Aug 01, 2009 | Bosch SHU5315UC Dishwasher

2 Answers

Error code F 21


I have a Bosch Classixx 6 1200 express washing machine showing error code F21 on the display, what is it?

Apr 05, 2009 | Bosch Classixx WFO 2866 Front Load Washer

1 Answer

Bauknecht GF7199 F7 light has come on


F7 error indicates a fault with the water flow meter .

Check the sump filter at the bottom of the dishwasher, then close the door and turn on the power. then hold the start button with the + and - buttons under the LCD display, until the drain pump starts. This should then reset the dishwasher.

Hope this helps .

Mar 06, 2009 | Bauknecht Dishwashers

3 Answers

Have got a bauknecht dishwasher model no gcx 5521. had the same problem last year. water is not going into the machine it looks like the water stop device activated. I think its something to do with a...


have got a bauknecht gsx4756 which when started beeps continually and start light flashes. it automaticaly then flashes the rinse button as well. I have reset holding down start and mode selection button next to the start button the fault keeps recurring. just wanting to know what the problem is before paying an engineers extortionate call out fees

Jul 31, 2008 | Bauknecht Dishwashers

3 Answers

Need diagnostic test for Kenmore Elite Oasis HE top load washer it is making beeping noises and has a mind of its own


pick any button but power or pause (spin works ok) pres and hold 3 sec release 3 sec hold 3 sec release 3 sec hold 3 sec this will put intio diagnostics usually if a fault code is stored this will show first press same button to step through post fault code if any asap and will try to help may to try several times to get into diagnostics

Jun 21, 2008 | Washing Machines

2 Answers

Bauknecht washing machine fault


Had the same problem myslef yesterday. Have rung whirlpool this morning and they advise that the code F7 refers to a short circuit.

May 27, 2008 | Washing Machines

2 Answers

Bauknecht GSX4756 dishwasher


I have this problem frequetly - it's an easy one to fix! Just press the programme button which changes the programme setting you want (on my built-in GSX4756 it's the last button on the right) and keep it pressed in until the beeping stops. Then start it again (will probably be on the rinse programme if it's like mine).

Feb 08, 2007 | Bauknecht 24 in. GSFP3988 Built-in...

1 Answer

Whirlpool ADP5966 fault code F8


just choose another prog setting and hold the start button in for a few seconds.

Nov 16, 2006 | Whirlpool 24 in. ADP5966 Free-standing...

Not finding what you are looking for?
Whirlpool 24 in. ADP5966 Free-standing Dishwasher Logo

Related Topics:

597 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4363 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Bruce Denton

Level 2 Expert

273 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...