Question about Schlage Locks & Locksmithing

2 Answers

Schlage FE365v keyless entry lock.. Lost manual. Forgot 6 digit programming code. Need instructions to restore and set all new codes.

Schlage FE365v keyless entry lock.... Cannot find my user manual, and I cannot remember my 6 digit programming code. How can I restore the lock and set a new code?

Posted by on

  • Heather Jan 17, 2013

    I have a keyless entry that no longer opens with the code. I changed the batteries and when I enter the code the light flashes green but won't open. Any solution?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 1 Answer

Look on the sticker located inside the outer panelo on the lock. you are going to need to disassemble the unit but it is in there.

Posted on Aug 08, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

If you take it apart it is on the inside usually.

Posted on Jul 29, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Schlage keyless lock lost 6 digit code and no sticker inside either


You will need to take the keypad look off of your
door and record the 6 digit programming code and the two factory
default PIN codes. You then need to perform the factory reset to
erase any codes and restore the lock back to the factory defaults.
This procedure is outlined, as well as the programming of the device, in the attached instructions.

http://www.factorylocks.com/PDFs/Programming%20Instructions.pdf

Regards,
Leslie
Factorylocks.com
877-345-6257 (877-34-LOCKS)

Jan 13, 2013 | Schlage FE595 Plymouth Electronic Keypad...

1 Answer

I need to change the batteries and reset the pass code in (2) keyless locks ("Locknetics On Board"). The owner's manuals were never given, and the key (Schlage) override was never used.(No...


How can I program my electronic keypad lock when the instructions with the programming code have been lost?
The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.
This number is the programming code referenced in the information for changing the entry code.

This link will take you to the page that you need to get started:

http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Then scroll down to this heading on that page:
Electronic Security-Keypad Entry Flex-lock FE595/Keypad Entry Auto-Lock FE575 Documents

There's a wealth of info under that heading. You will be able to see a PDF file of the original print instructions, as well as a video of how to install the lock. This installation video (third item down) will be useful to allow you to disassemble it and view the sticker. This is also a great time to change the 9-volt battery! Batteries should be replace about every three years.
The eighth item under that same header is a video which walks you through how to reprogram the keypad to your new code, using that programming code that you found on the backside of the keypad.
A note about the PDF files: If you cannot view a given file, you need to first install Adobe reader. You can get the free download from here:

http://get.adobe.com/reader/

Good luck--and please provide feedback if this helps!

Jul 06, 2011 | Schlage FE595VCAM716ACC Camelot Keypad...

1 Answer

I lost the manual and i need to reprogram the codes


How can I program my electronic keypad lock when the instructions with the programming code have been lost?The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

This link will give you instructions for various models of Schlage locks:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx
There is a video on this page, showing how to change codes.

Good luck!

Jan 22, 2011 | Schlage Electronic Lock FE595 Plymouth or...

1 Answer

How do I set the key pad to my on code on my schlage electronic keyless lock


How can I program my electronic keypad lock when the instructions with the programming code have been lost?The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

This link will give you instructions for various models of Schlage locks, including the BE 365:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Good luck!

Jan 13, 2011 | Schlage Lock BE365VCAM716 Electronic...

1 Answer

I need to change my security code asap but ive lost the manual to the instruction can u please help


How can I program my electronic keypad lock when the instructions with the programming code have been lost?The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

This link will give you instructions for various models of Schlage locks:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Good luck!

Jan 08, 2011 | Schlage BE365-CAM BE365CAM619 Satin...

1 Answer

I am looking for the manual that would tell me how to reset the codes in my keylsee entry locks


How can I program my electronic keypad lock when the instructions with the programming code have been lost?The back plate of the keypad side of the lock on the exterior of the door has a sticker which includes the serial number, six digit programming code and two pre-programmed four digit user codes. The lock must be disassembled to a point the exterior of the lock can be pulled away from the door and the information on the sticker made note of.

This link will give you instructions for various models of Schlage locks:
http://consumer.schlage.com/Service-Support/Pages/InstructionandManuals.aspx

Good luck!

Dec 28, 2010 | Schlage Locks & Locksmithing

1 Answer

I have the same kind of problem. I have the programming code, but when I enter it, after entering the 4 th digit the lock blinks an error thinking I entered an incorrect user code?? So I think I might have...


Restore the lock first

1.disconnect battery
2.press and release the SCHLAGE button
3.reconnect the bat and wait until SCHLAGE is no longer lit.
4. within 10 sec,press and hold SCHLAGE until SCHLAGE lights green and the lock beeps.

The lock is back to factory now.
Now add your user code.

Adding a new user code
DPC is-digit programming code
DUC is digit user code
Yellow sticker has factory 6 digit programming and 4 digit user code on it.

1. 6DPC push SCHLAGE, push 1, enter 4DUC twice.

this lock will only take 2 user codes.

Hope this helps. Leave feedback for others if it helps

Aug 30, 2009 | Schlage BE365-PLY BE365PLY626 Satin...

1 Answer

Need info to change code


Here's a link to the Schlage web site with pdf's and videos showing how to operate and program your lockset.

Just select which info you need from the list on the page.

http://consumer.schlage.com/customerservice/FE575_install_inst.asp

Hope you find this Very Helpful - Best regards!

Aug 20, 2009 | Schlage FE575-CAM-ACC FE575CAM505ACC...

Not finding what you are looking for?
Locks & Locksmithing Logo

Related Topics:

10,067 people viewed this question

Ask a Question

Usually answered in minutes!

Top Schlage Locks & Locksmithing Experts

JOHN LAPIER

Level 3 Expert

2595 Answers

Mike

Level 3 Expert

4363 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Are you a Schlage Lock and Locksmithing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...