Question about Kitchen Ranges

1 Answer

Error code f21 sud

I started a self cleaning cycle of 3 hrs and about 1h20 into it it started beeping continuously with the code EO 21. What's up with that. I could not eeven stop it. I had to shut off the breaker and even after turning on the power it kept beeping. Now the barker is off and I'm trying to figure this out.

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 288 Answers

Firstly you need to unplug and need to check the pump is not blocked. Take the machine to a rear yard or area where you can drain the water from the machine as there will be a few gallons inside it.
The pump may have a filter unit on the front bottom of the machine or hidden at the rear behind the panel . There will be a lot of water still in the machine which ever filter you need to remove.
Sounds as if its blocked with socks , underwire Bra money etc a DRAINAGE FAULT F21

Posted on Jan 09, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

SOURCE: Error code E1 -F5- Broil element comes on and wont shut off

I just did the self clean option and when it was done I received the error code E1 -F5- and it does have to do with the door latch. After turning off the power to the stove I was able to open the door and wiggled the latch and that solved the problem.......

Posted on Oct 24, 2007

MARLON KELLER

  • 111 Answers

SOURCE: EO F2 code

THIS IS GENERALLY A BAD ELECTRONIC RANGE CONTROL OR ERC BOARD

If you need further help, reach me via phone at https://www.6ya.com/expert/marlon_56d9a24f02585258

Posted on Jun 01, 2008

Anonymous

  • 1 Answer

SOURCE: clock assembly

my automatic cleaning setting in my oven will not heat up. I set "clean" on both dials and put the lock on, the fan comes on but no heat. Is there a certain system to turning it all on and the timer so it will work?

Posted on Jun 02, 2008

philzee

  • 38 Answers

SOURCE: Cancelled self-clean, F9 code came up, door lock light flashing, can't use oven

HI,
your model number confirms that your range was manufactured by WCI (Frigidaire). although this doesn't help you now, it may help if parts are needed.

now, there is an indepth guide online to fixing this common problem and I would like you to go through it and see if it helps you solve your problem.

http://www.applianceaid.com/clean-lock.html

If you have found this site previously then I apologise, if you still need help, by all means post again and someone more qualified may help.

Hope this is of use to you ;)

Phil

Posted on Oct 28, 2008

ericvonk

  • 5 Answers

SOURCE: Jenn air range model SCE30600B error code FC

replace the entire range: Jennair does not know how to design, make, or program electronics. It makes steel boxes that provide heat but electronics - that's not within their ability. Buy a Kenmore or a GE and your beeping problem will go away.

Posted on Aug 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Error message SUD and F21 even after unclogging the filter


Push the pause/cancel button twice to clear your message. Then run through a rinse/spin cycle. Next try a normal load without any detergent. SUDS is usually from too much detergent. If this fails, checked the hose for kinks. Check connections and if all that fails, you will probably have to replace the pump. Good Luck!

Feb 04, 2014 | Maytag MAH6700AWW Neptune Front-Load...

1 Answer

Maytag washer throwing fault code 21


An "F21" or "F02" error code is indicative of a slow draining cycle, normally caused by a clogged or kinked drain hose. If an "F21" or "F02" error code appears, check the drain hose on the back of your washer to ensure that it is not clogged or bent. Once the drain hose has been unblocked, the error code should disappear and the machine drain properly. However, if you have a high efficiency washing machine and the error code continues to appear, make sure you are using the correct detergent; because high efficiency machines use much less water than traditional washing machines, they require the use of a low sudsing detergent. Traditional detergents may produce too many suds, which can block the machine's drain hose and lead to slower draining cycles.

May 20, 2012 | Maytag Washing Machines

1 Answer

What does it mean if the washer is not draining and has a flashing f where the time shows?


I have the manual for this machine. Under "Code 21" it says the following:
"F21" (Drain Problem) Select STOP twice to cancel the cycle. Unplug washer or disconnect power. Check the following: Is the drain hose kinked? Is the drain hose frozen? Is the drain hose clogged? Is the drain hose more than 96" (2.4 m) above the floor? Plug in washer or reconnect power. Re-select cycle and press START. If the problem remains, call for service.
For "SUDS" code, the following:
"SUD" (Suds Routine) When excessive suds are detected, a suds routine automatically starts. This routine removes extra suds and assures proper rinsing of your garments. "SUD" is displayed during rinsing to inform you that Suds Routine was activated. Use only HE (High Efficiency) detergents.
Here is some more information that may help you as well:
"F" Codes other than F20, F21 and F22 Select STOP twice to cancel the cycle. Select DRAIN & SPIN if there is excessive water in the washer. Re-select cycle and press START. If the problem remains, call for service.
I hope this is of some help to you, Please rate and comment, Thank You
Joe

Sep 07, 2011 | Kenmore HE2 Plus Front Load Washer

1 Answer

F-21 code several times. We clean the pump. Start again the rinse/drain and spin cicle, and now present sd code and later f-21 code. What we need to do.


I have the manual for this machine. Under "Code 21" it says the following:
"F21" (Drain Problem) Select STOP twice to cancel the cycle. Unplug washer or disconnect power. Check the following: Is the drain hose kinked? Is the drain hose frozen? Is the drain hose clogged? Is the drain hose more than 96" (2.4 m) above the floor? Plug in washer or reconnect power. Re-select cycle and press START. If the problem remains, call for service.
For "SUDS" code, the following:
"SUD" (Suds Routine) When excessive suds are detected, a suds routine automatically starts. This routine removes extra suds and assures proper rinsing of your garments. "SUD" is displayed during rinsing to inform you that Suds Routine was activated. Use only HE (High Efficiency) detergents.
Here is some more information that may help you as well:
"F" Codes other than F20, F21 and F22 Select STOP twice to cancel the cycle. Select DRAIN & SPIN if there is excessive water in the washer. Re-select cycle and press START. If the problem remains, call for service.
I hope this is of some help to you, Please rate and comment, Thank You
Joe

Sep 04, 2011 | Kenmore HE2 Plus Front Load Washer

1 Answer

Won't finish cycle 21 F- flashing on panel


F21 error code is indicating that it is taking too long to drain water.

Your details indicate that you are using too much detergent or the wrong type of detergent and causing excessive suds. The drain pump can not pump suds out. The washer requires HE (High Efficiency) detergent formulated for front loading washers.

Cut back on the detergent and it will most likely operate correctly.

NOTES:
* After four (4) minutes the "Sd" error will be displayed, and then four (4) minutes later the "F21" error code will be displayed.
* Press STOP two (2) times to clear the display.

Possible Causes:
- Using too much High Efficiency (HE) detergent and causing too much suds.
- Using NON-HE detergent causing too much suds.
- Kink in drain hose
- Debris or foreign objects in drain pump filter.

The drain filter is located behind the lower access panel.

NOTE: Disconnect the power cord before removing the lower access panel and cleaning out the drain pump filter.

Remove the two screws (key#21) securing access panel. The filter cap (key#14) is removed by turning it counter clockwise. NOTE: Be sure that all the water has pump out before removing the cap. Have some large towels handy because there will be water coming out the filter/pump once you remove the cap. Check and clean the filter and remember to reduce the amount of detergent and the washer should perform as designed

zjlimited_423.gif__zjlimited_424.gif

Hope helps (remember to rate and comment this free answer)..

Jun 10, 2011 | Kenmore HE2 Plus Front Load Washer

2 Answers

F21 code flashes


Lets see what an F-21 is shall we? F21 Long drain Possible cause: Clogged filter, clogged/failed pump, suds detected by control.3a5b94a.jpgb4a897e.jpg55f108d.jpg

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Jun 19, 2010 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Error code f-21, cleaned drain then error code rl


Hello,"F21" is a Long Drain error code which is usually an indication that you may have an obstruction somewhere in the drainage system. Most commonly, there is something lodged in the drain pump or inlet line running from the wash tub to the pump. There is a white screw off cap on the drain pump that you can remove to inspect the pump impeller and clean. The following link explains.

http://www.fixya.com/support/r3608588-f21_error_code
Included is a follow-on link that explains how to check the drain pump to clean. You may also have to remove the inlet hose that runs from the bottom of the wash tub to the inlet side of the drain pump. Debris and small articles of clothing such as socks or under garments can become lodged in this area as well causing the drain cycle to fail.

NOTE: A "SUD" error code can often occur in conjunction with the "F21" error code. This is due to air being detected in the drainage system, which can occur if the pump is not running, or if you have an obstruction BEFORE the pump. You need to remove the inlet hose from the pump to ensure it is also not blocked. Correct your drainage system fault, and the SUD error (if displayed) should go away.

NOTE: If these preliminary measures do not correct your problem, you may have to replace the drain pump. It does not take much to damage the pump impeller or motor. Since the error code is generated if the drain cycle exceeds 8 minutes, if the pump is damaged and can't pump at the required volume, the error code will continue to appear until the pump is replaced.
Thanks

May 24, 2010 | Maytag EPIC MFW9700S Front Load Washer

1 Answer

Error f-21 is displayed after a partial cycle.


"F21" is a Long Drain error code. This is an indication that you have an obstruction somewhere in the drainage system. Most commonly, this means there is something lodged in the drain pump or inlet line running from the wash tub to the pump. There is a white screw off cap on the drain pump that you can remove to inspect the pump impeller and clean. The following link explains:

http://www.fixya.com/support/r3608588-f21_error_code

Included is a follow-on link that explains how to check the drain pump to clean. You may also have to remove the inlet hose that runs from the bottom of the wash tub to the inlet side of the drain pump. Debris and small articles of clothing such as sock or under garments can commonly clog in this area as well causing the drain cycle to fail.

NOTE: The "SUD" error code can often occur in conjunction with the "F21" error code. This is due to air being detected in the drainage system, which can occur if the pump is not running, or if you have an obstruction BEFORE the pump. You need to remove the inlet hose from the pump to ensure it is also not blocked. Correct your drainage system fault, and the SUD error should go away.

If you have any questions about this repair, or need additional assistance, please let me know. I hope this helps you.

NOTE: If these preliminary measures do not correct your problem, you may have to replace the drain pump. It does not take much to damage the pump impeller or motor. Since the error code is generated if the drain cycle exceeds 8 minutes, if the pump is damaged and can't pump at the required volume, the error code will continue to appear until the pump is replaced.

Nov 12, 2009 | Kenmore Elite 45986 Front Load Washer

2 Answers

F21 suds comes on eveytime after wash and shuts washer off


"F21" is a Long Drain error code. This indicates that you have an obstruction in the drainage system. More than likely you probably have a clog in the drain pump. The following link explains:

http://www.fixya.com/support/r1484065-f21_error_code_whirlpool_duet_kenmore

Included is a follow-on link that explains how to check the drain pump to clean. You may also have to remove the inlet hose that runs from the bottom of the wash tub to the inlet side of the drain pump. Debris can commonly clog in this area as well causing the drain cycle to fail.

If you have any questions about this repair, or need additional assistance, please let me know. I hope this helps you.

NOTE: If these preliminary measures do not correct your problem, you may have to replace the drain pump. It does not take much to damage the pump impeller or motor. Since the error code is generated if the drain cycle exceeds 8 minutes, if the pump is damaged and can't pump at the required volume, the error code will continue to appear until the pump is replaced.

NOTE: The "SUDS" error can commonly occur with the F21 error code as this is usually generated when air is sensed in the drainage system.

Sep 26, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Whirlpool duet washer flashing sud then f21 ????????


The "SUD" error is in direct relationship the other error code. "F21" is a Long Drain error. The following link explains:

http://www.fixya.com/support/r1484065-f21_error_code_whirlpool_duet_kenmore

If something is preventing water from pumping through the drain pump, you will often get a "SUD" error as air is developed in the pump. Make sure you double check all the drain lines as well.

If you have questions, or require additional assistance, please let me know before you rate the solution. I hope this helps you.

Jan 28, 2009 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Paul Carew

Level 3 Expert

3484 Answers

Brad Brown

Level 3 Expert

18154 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...