Question about Canon I-Sensys Mf4550d All-In-One Laser Printer Print, Copy And Scan

1 Answer

My printer is printing only 1/4 vertically

I own a Canon mf4550d and when i do print or copy pages it print only 1/4 vertically of the whole page. Also there is no error messages or cartridge empty messages. Any help please.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 312 Answers

I would first take your toner out and shake it and see if this helps. Sounds like a defective cartridge and or transfer roller.

Posted on Jan 31, 2015

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: Printing problems

Same problem. Definitely NOT a leaking cartridge or head. (Replaced both with known good set)

Posted on Jun 25, 2008

Anonymous

  • 2 Answers

SOURCE: Smartbase MP390 Printer - error ##345

canon smartbase mp390 error ##345 check printer can anyone help me

Posted on Feb 08, 2009

nyilasrobert

Robert Nyilas

  • 627 Answers

SOURCE: How to check total printed pages in canon LBP2900B printer

press resume button at least 4 seconds

Posted on Jul 24, 2009

Anonymous

  • 787 Answers

SOURCE: canon mx318 u051

Try to press and hold the resume button for 5 seconds.If this not help you need to replace the ink cartridges.

Posted on Oct 26, 2009

Anonymous

  • 1 Answer

SOURCE: canon mf 6550 copy no print out its came out empty page

We had the same problem with our mf6550 printing blank pages after we changed the toner cartridge. I called the support desk today and they said it is the shutter. They told me to remove the toner cartridge and then (without a cartridge in) close the door briskly. Then open the door, install the cartridge and again close the door briskly. It worked! He said it may be a permanent fix or it may act up again. He also said I could take it to a service center to have it fixed permanently. The service desk # is 1-800-828-4040. They can tell you where the nearest service center is. Good luck.

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Canon irc4580i print dark problem


In the process used printer, will be inevitable printed page by your printer have the bad quality prints. For example: Toner specks, Light image, Vertical line, Dropouts, background, Toner smear, Vertical black line and band, Vertical white line, Background scatter, Black pages, Loose toner, Horizontal stripes, Ghost, Uneven Density, poor fusing ...
The common print quality problem Canon IRC-4580 printer
Currently, The Canon IRC-4580 is the laser printer have high speed, easy to use, friendly for user and printing clear text.
However, we can not avoid the damage of some components of the printer when used.
In this article, I will introduce some basic errors with printing quality problems of Canon IRC-4580 printer and "How to fix it".
After viewed artical, you know:
- How to fix (repair/solve) Vertical line (black or white) in Canon IRC-4580 printer
- How to fix (repair/solve) Poor fusing (loose toner) in Canon IRC-4580 printer
- How to fix (repair/solve) Uneven Density in Canon IRC-4580 printer
- How to fix (repair/solve) Light image in Canon IRC-4580 printer
- How to fix (repair/solve) Ghost in Canon IRC-4580 printer
1. Fix print quality problem "Vertical line" for Canon IRC-4580 printer How to fix print quality problem Vertical line
This plobrem "Vertical line" is usally error of Canon IRC-4580 printer. For this "Vertical line" error, technicians divided into two smaller error are: Vertical black line and band and Vertical white line.
Description:
- Vertical line and band: On the printed image appear some straight thin black vertical.
- Vertical white line: On the printed image appear some white vertical voids.
Error location:
- Surface of the charge roller
- OPC drum
- Cleaning blade
- LSU unit
- Developing roller

Cause of error "Vertical line" on the printed page:

- May be surface of charge roller scratched or dirty by toner powder.
- May be have some grooves on the OPC drum.
- May be cleaning blade is damaged.
- May be LSU window or LSU lense has dirty.
- May be surface of developing roller has scratched.

How to fix(repair) "Vertical black Line and Band" for {{SPkey1}} machine:

- Replace the charge roller of toner cartridge.
- Replace the OCP drum.
- Replace the cleaning blade
If printed page are not improved
- Clean the LSU unit by soft cotton cloth and try to print. If Vertical line is not clear on the printed page you should replace LSU unit.
- Replace new axis developer and try to print
2. Solve print quality problem "Poor fusing (loose toner)" for Canon IRC-4580 printer. How to fix print quality problem loose toner
Description loose toner: Toner is not properly fixed on paper, use to hand rubbing lightly on the printed image toner powder may be stick in hand
Error location: toner cartridge or fuser unit

Cause of error "Dark Image or black" on the printed page:

When toner cartridge is empty. You toner refilled by toner powder ware not compatible. This is makes toner cartridge components demaged and temperature of fuser unit is not enough melt to toner powder

How to fix(repair)"Poor fusing (loose toner)" on the printed page for Canon IRC-4580 printer:

With this error, you should replace toner cartridge or fuser unit to fix it.
3. How to fix print quality problem "Uneven Density" for Canon IRC-4580 printe How to fix print quality problem Uneven Density
Description: The printed page has one half light and one half clear.
Error location: Toner cartridge, transfer roller, springs, doctor blade

Cause of error "Uneven Density":

- The pressure force on the left and right springs of the transfer roller is not even.
- May be toner low also causes this error
- Doctor blade has bent
How to repair error "Uneven Density" on the printed page for Canon IRC-4580 printer:
- Replace springs and transfer roller.
- Toner refill toner cartridge Canon IRC-4580 and reset toner cartridge chip (replace new chip) or replace new genuine toner cartridge.
- Replace doctor blade.
4. How to solve print quality problem "Light image" for Canon IRC-4580 printer How to fix print quality problem light image
Description: The printed image is all light and no Ghost.
Error location: Toner cartridge, Developer, HVPS board

Cause of error "Light image" on the printed page

- Enabled toner save.
- Toner cartridge is low
- OPC drum may be faulty by strong light intensity
- Temperature in room is below than 10*C
- Bad contact caused by the toner dirty between the high voltage terminal in the HVPS and the one in the set
- Abnormalities output from the HVPS

How to fix(repair) error "Light image" on the printed page for Canon IRC-4580 printer:

- Disable toner save by change in printer driver.
- Toner refill toner cartridge Canon IRC-4580 and reset toner cartridge chip (replace new chip) or replace new genuine toner cartridge.
- Replace the OPC drum.
- Replace developer.
- After printer is power on, wait 30 minutes then start printing
- Clean up the contact between the high voltage terminal in the HVPS and the one in the se- Replace the new HVPS if the problems are not solved by 4 away above.
5. How to fix print quality problem "Ghost" for Canon IRC-4580 printer How to fix print quality problem Ghost
Description: Ghost occurs intervals of the OPC drum or transfer roller.
Error location: Toner cartridge, Developer, HVPS board

Cause of error "Light image" on the printed page

- OPC drum has fauty.
- The life of the transfer roller has been expired
- The high voltage terminal is contaminated by toner powder or

How to fix(repair) error "Light image" on the printed page for Canon IRC-4580 printer:

- Replace OPC drum
- Replace transfer roller
- If performed 2 away and the error does not clear, you should replace ganuine toner cartridge .
- Replacce HVPS board.

Oct 29, 2016 | Canon Office Equipment & Supplies

1 Answer

Copier is not connected to PC. Stand alone. Vertical line on copy


To determine if the line is caused by the cartridge, try printing a test page. Not sure of your model, but there should be a menu setting to print a configuration page. If that configuration page prints out clean, then there is likely debris in the scanning area of the document feeder. You should be able to locate the debris by lining up the vertical line with your feeder. If you could reply back with the model of your Canon device, we can help you a bit more. Alternatively, you should be able to pull the cleaning instructions from the manual for your copier.

Dec 27, 2015 | Canon Office Equipment & Supplies

1 Answer

Why does the printer keeps having a paper jam fault on final exit slot?


It sounds like the exit sensor is sticking, so the printer doesn't know the paper has exited & throws a jam.

Aug 24, 2014 | Cannon Office Equipment & Supplies

1 Answer

How to reset the fuser on Canon mf4550


Reset it how? If it is the page count, you can do that in the service menu. Generally, they do this for a reason and youcought to replacecthecfuser if it says you should!

May 29, 2014 | Canon I-Sensys Mf4550d All-In-One Laser...

1 Answer

Reset canon mf4550d


To reset a Canon i-SENSYS MF device, it is necessary to contact the Canon helpdesk. They will arrange a callback to guide you trough the reset. The steps for a reset are not public and if you can find them on the web, it is not safe to try resetting the device on your own. When clicking on a wrong option, it can be that the device has to be send to service for repair afterwarts.

May 05, 2014 | Canon I-Sensys Mf4550d All-In-One Laser...

1 Answer

Canon image runner c5800 printing vertical lines


have you ran a test page , the test will take about 30 sheets of paper it will test everything and will correct itself
good luck

Dec 04, 2013 | Office Equipment & Supplies

3 Answers

Canon LASER SHOT LBP-1210 Printer how to set legal page


For printing the Legal Size (8.5′x14′) in cannon LBP-1210, follow the instruction:
Step 1- Go to start
Step 2-printer and faxs
Step 3-select printer(Canon LASER SHOT LBP-1210)
Step 4-go to file
Step 5-select Server properties
Step 6-select creat new form (for legal page)
Step 7-give form name legal 1
Step 8-give paper size width 8.50in, hight 14.00
Step 9-give paper margin top 0.30in, left 0.30in, right 0.30in, bottom 0.30in
Step 10-select save form Step 11-then select advanced
Step 12-select informational notifications for local printers
Step 13-select apply
Step 14-then close
Step 15-select Canon Laser Shot LBP-1210
Step 16-select printer
Step 17-select properties
Step 18-select-select forms
Step 19-select change forms
Step 20-select legal 1
Step 21-select OK
Step 22-select apply
Step 23-select OK
Remember: 1 U need to set paper size (8.5′ x 14′) manually in the word documents and befor printing you need to set in printer properties "Legal 1′ for printing. Print preview may not show the whole page but the printer will print the whole page.
All the best.

Apr 24, 2010 | Canon LASER SHOT LBP-3000 Printer

1 Answer

I wanted one paper printed instead of one i have a whole pile of papers how do i stop same documents printing


Open "File"

Open "Print"

Goto "Print range"

Click on "Pages"

In the first box enter the number of the page you want to print

In the second box enter the number of copies you want.

If you want only 1 copy enter 1 in both of the boxes..

Hope this helps

Apr 10, 2009 | Canon imageCLASS MF8170C All-In-One Laser...

4 Answers

Print Problem - vertical lines


If the problem only occurs when using the document feeder, the problem is not usually caused by the drum. When using the document feeder, try to notice where the scanner (the light assembly under your scan glass)stops just before the paper is being fed. Some multifunction machines have a small piece of glass that is separate from the large scan glass and the scanner assembly stays parked underneith it as the original is being fed over it. Most likely there is something on the glass where the scanner parks as originals are being fed thru the feeder. When putting your original on the large scan glass to copy, the mark on the glass will only show as a spot, but will show as a vertical line thru the whole copy when using the feeder.

Feb 23, 2007 | Brother MFC-7820N Laser Printer

Not finding what you are looking for?
Canon I-Sensys Mf4550d All-In-One Laser Printer Print, Copy And Scan Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

old marine
old marine

Level 3 Expert

2261 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...