Question about Whirlpool 24 in. ADP5966 Free-standing Dishwasher

Open Question

F3 fault code

First the dishwasher gave F4 fault code, which I fixed by replacing the OWI sensor. But new problem appeared instantly. Now it gives F3 code after about 3 minutes operating. I noticed that washer doesnt heat the water. I tried also to change incoming water temperature to 60 celcius instead of cold water, but it makes no difference.

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Ian Greenland

  • 351 Answers

SOURCE: Whirlpool dishwasher ADP 4732AL

sound like you have a valty inlet valve if your model has the valve built into the hose you will have to replace the hose assy.

Posted on Mar 20, 2008

Ad
micromaster

micromaster

  • 3614 Answers

SOURCE: Does not Wash

first check if there was an object that obstruct the motor, try to clean that area, and run again the unit, if the problem was still there, then could be the washer motor was broke.

Posted on Aug 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a adg7560/1. the cycle starts but ends after a few minutes. the light flashes four times


Run the dishwasher through a test mode


Test Mode


Make sure the appliance is empty of water before running Diagnostics as it does not pump out before starting to fill and therefore you could overfill the appliance.
Open the door and set the program to the first program. (Normally rinse).
Turn the power off.
Press and hold the start button and while holding turn the power on.
After a little while the start button will flash, release the button.
Press the start button once and close the dishwasher door.
The machine will now run through a diagnostic routine.
Should take about 20 mins.
The machine will stop during diagnostics if an error is found and will display the error code. If no error is found it will complete the diagnostics and end the programme.

To exit diagnostics at any time just press and hold the start button till the programme is cancelled
Error codes


F1. Single flash. NTC Break. NTC open circuit/short circuit or ambient temperature less than 3 Celcius

F2. 2 Flashes. Water leakage. Floater switch LS6 in drip tray has switched.

F3. 3 Flashes. Heating system defect. Heater or relay on control board defect. Chack also cabling.

F4. 4 Flashes. Draining failure. Drain pump, control board OWI or water indicator defect.

F5. 5 Flashes. Sprayarm Blocked (not present on VBL version. On 1 digit display will show as F and flashing start led).

F6. 6 Flashes. Water valve (WV1) is switched on but flow meter (FM) senses no impulses (less than 10 impulses in 10 secs) and the water indicator (WI) is at a low level
Water Valve Closed. Water inlet hose blocked.
Water inlet valve (WV1) defective. Flow meter (FM) defective (leads to FM failure)

F7. 7 Flashes. Flow meter failure. Flow meter defect. Water inlet valve defect or water inlet hose blocked.

F8. 8 Flashes. Water level failure. Sieve strongly dirty or big amount of foam inside to less water.

F9. 9 Flashes. Continuously Water Inlet. Water inlet valve mechanically not closed or control board defect.

FA. 11 Flashes. OWI failure. Dirty OWI lens. OWI defect or control board defect. Check cabling.

FB. 12 Flashes. Motorised Diverter Valve

FC. 13 Flashes. Water Hardness Sensor Failure

A fault with no fault code indication = faulty module

Read more: http://www.diynot.com/forums/viewtopic.php?t=200838#ixzz2zKhYFHxt

Apr 19, 2014 | Whirlpool Dishwashers

1 Answer

Range displays code of F4 and stops working


F4 Oven temperature sensor (RTD) shorted Replace Oven temperature sensor (RTD)

The F2, F3 and F4 codes refer to problems with the oven temperature sensor or the keypad. If you see the two-digit F2 code, it means your keypad has shorted and the ERC must be replaced. The four-digit F2-E0 code means that the oven temperature is too high. Test the door lock and the relay operation, and correct as necessary. A two-digit F3 code means an open temperature sensor or thermal fuse, so those parts must be replaced. A four-digit F3-E0, F3-E1, F3-E2 or F3-E3 code or a two-digit F4 code means that either the oven is registering as too hot or the temperature sensor has shorted. Either way, the oven temperature sensor must be replaced.
Hope helps.

Jun 14, 2011 | KitchenAid Kitchen Ranges

1 Answer

Fault codes F1 and F2


Just two work there:
1.- Replace the touchpad or the clock (ERC) if the code "F1" is displayed. Disconnect the ribbon connector to the touchpad. If no code is displayed after an hour, replace the touchpad. If the code displays again, replace the clock.
2.- Replace the oven temperature sensor if "F2," "F3" or "F4" is displayed. "F2" indicates the oven temperature is too hot and the oven temperature sensor is suspect. "F3" or "F4" indicates the oven temperature sensor or shorted or open.

Parts replacement coudl look in www.repairclinic.com

Hope helps.

May 02, 2011 | Magic Chef Ovens

1 Answer

F3 f4 gaas oven when preheated these numbers appear it beeps and shuts off


Hi, replace the oven temperature sensor if "F2," "F3" or "F4" is displayed. "F2" indicates the oven temperature is too hot and the oven temperature sensor is suspect. "F3" or "F4" indicates the oven temperature sensor or shorted or open.

Jan 22, 2011 | Magic Chef Ovens

2 Answers

I have an error code f4 on my whirlpool adp 8966 dishwasher can you tell me what it means please


F4 indicates draining failure.Your washer drain pump starts and after 4 minutes the OWI(optical water indicator) detects that mashine is 'not empty'

Posible mailfunction reasons:
The drain pump must be defective/blocked
The siphon would have got closed
The control board would have got damaged
OWI defective

Apr 04, 2010 | Whirlpool 24 in. ADP6940 Dishwasher

1 Answer

The oven isn't working and it says FO in red letters


GE / Hotpoint / RCA
Oven Fault Codes
Display Condition Remedy
F0 & F1 Failed Thermistor Control Replace ERC
F2 Oven Temp Exceeds 590 with unlocked door High resistance in Sensor, likely a bad sensor
F3 Open Sensor circuit Open (blown) sensor fuse or bad Sensor
F4 Shorted wire or Sensor locate short and correct it
F7-A Function pad button stuck Clean and unstick
F7-B Bad Clock Replace Clock
F8 Electrical component failure Replace ERC
F9 Program with door circuit Check wiring

Frigidaire / Westinghouse / Tappan / Gibson
Oven Fault Codes
Display Condition Remedy
F0 & F1 EOC failure Replace EOC
F2 Oven over heat Defective Sensor or EOC
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it
F5 EOC failure Replace EOC
F6 EOC failure Replace EOC
F7 EOC failure Replace EOC


Maytag / MAYCOR / Magic Chef / Jennair / Admiral
Oven Fault Codes
Display Condition Remedy
F0 Function key shorted or stuck button Clean and unstick button or replace Touch Pad or Clock
F1 Defective Touch Pad or Membrane Replace Touch Pad or Membrane
F2 Oven over heat defective Relay Board or (if present) or defective Sensor
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Hardware, safety circuits disagree Replace Clock
F6 Missing AC (power) signal Check for proper voltage (plug, breaker, etc.)
F7 Function key shorted or stuck button Clean and unstick button or replace Touch Pad or Clock
F8 A/D Warning Replace Clock
F9 Door Lock Warning Check door lock circuit or Replace Clock


Amana / Caloric
Oven Fault Codes
Type with display - glass link ERC
Display Condition Remedy
F0 No Safety Signal Replace adapter board
F1 No Safety Signal Replace ERC
F2 Oven over heat Replace defective Sensor
F3 Oven Sensor Open Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F7 Shorted Touch Panel Replace Glass Panel
F9 Door Latch Error Check latch
FF Lock Error Check switch and motor
ERC III - Relay board with separate board/push buttons
F0 Shorted Push Pad Replace Push Pad
F1 Defective ERC Replace ERC
F2 Oven over heat Replace defective Sensor
F3 Oven Sensor Open Check/Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Defective ERC Replace ERC
F6 Defective ERC Replace ERC
F7 Shorted or sticking button Clean button or replace touch pad
F8 Defective ERC Replace ERC
F9 Door Latch Error Check latch


The following diagnostic chart Does not apply to Whirlpool 'Y' line products. If the model number contains a Y near the end of the number, DO NOT use this chart.
Whirlpool / KitchenAid / Roper
Oven Fault Codes
Ovens with 4 digit displays
Display Condition Remedy
F0-E0 Analog to Digital failure Disconnect panel for 30 seconds. if error re-appears then replace control
F1-E1 Defective ERC Replace ERC
F2-E0 Shorted Keypad Replace Keypad
F3-E0 Sensor or Sensor Fuse Open Replace Sensor or Fuse
F3-E1 Shorted wire or Sensor locate short and correct it or replace Sensor
F3-E2 Oven over heat Replace Sensor
F3-E3 Cleaning Temp over heat Replace Sensor
F5-E0 Door Error Check Door
F5-E1 Door Latch Check Latch
F5-E2 Door Switch Check Switch
Ovens with 2 Digit Displays
F0 Defective ERC Replace ERC
F1 Defective ERC Replace ERC
F2 Oven over heat Replace defective Sensor
F3 Oven Sensor Open Check/Replace Sensor
F4 Shorted wire or Sensor locate short and correct it or replace Sensor
F5 Defective ERC Replace ERC
F6 Problem with time keeping circuit Reset Time or cooking operation and check for proper ground
F7 Shorted or sticking button Clean button or replace ERC
F8 Defective ERC Replace ERC
F9 Door Latch Error Check latch and latch circuit


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Dec 18, 2009 | Ovens

2 Answers

Controlpanel flashes f 3


You have a faulty keypad. You could probably special order this part from a local appliance parts supply store for 50-60$ or purchase a new microwave.

Oct 22, 2009 | GE Spacemaker JVM1640SJ Microwave Oven

1 Answer

Program shows shows f4 and peeps


F4 indicates

DRAINING FAILURE

drain pump starts and after 4 minutes the OWI detects that mashine is 'not empty'

posible mailfunction reasons:

drain pump defective/blocked
siphon closed
control board defective
OWI defective


OWI - optical water indicator
================================
remember to unplug it from power if any repair is done
================================
Best regards and good luck

Oct 04, 2009 | Whirlpool 24 in. ADP6940 Dishwasher

1 Answer

Magic Chef Gas Range, model CGR3740ADW


magic chef fault codes

F1 1. Watchdog on board
2. Touch membrane defective To determine which component is at fault, disconnect ribbon strip. If NO fault code, replace membrane, otherwise replace board F2 Oven too hot Check oven temperature sensor F3 F4 Open or shorted oven temperature sensor Replace F5 Hardware and watchdog circuits disagree Replace clock assembly (also called the ERC) F6 Missing AC signal Replace clock assembly (also called the ERC) F7 Function key shorted Replace touch pad F8 Analog/Digital converter Replace clock assembly (also called the ERC) F9 Door latch Check door lock circuit F10 Function key stuck Replace touch pad

Jan 27, 2009 | Magic Chef 31000 Gas Kitchen Range

Not finding what you are looking for?
Whirlpool 24 in. ADP5966 Free-standing Dishwasher Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4363 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Bruce Denton

Level 2 Expert

273 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...