Question about Krell Audio Players & Recorders

Open Question

Cause blow fuse

I have a krell kav300i. The left channel failed after 2 speaker wires crossed. What amp fuse should I get to replace the fuse on the left channel ?

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Steven

  • 4 Answers

SOURCE: krell kav300i, increasing volume by itself.

I have 20 year exp. with Krell. Contact me directly.
Steven Leckrone
The Service Department
203-331-0671
sleckrone@snet.net

Posted on Oct 22, 2008

Ad
petraman7

Scott Frye

  • 1175 Answers

SOURCE: My audiosource 2 channel amp is dead in the left channel

Hi...
There's not alot of innerds on these amps.
They use a TDA7294 amplifier chip in the 50 WPC version and I have one here with both outputs gone bad.

The chip is cheap (<$10)

Posted on Apr 01, 2009

sonicboomele

sonic boom electronics

  • 1557 Answers

SOURCE: Model: st-202+ Speaker wires crossed while amp was

if you have located the fuses )blown) and are glass fuse type then simply take them out and replace with same type fuse if they a crt fuses you will need to know how to de solder and re solder with regards to them they are not pol sensortive

Posted on Jul 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Krell 2250 was operating well .. Suddenly left channel stopped .. checked the fuses all ok .. Any idea. ?


try subbing out another newer speaker for the left one ? if sound returns then that older speaker is defective .

Nov 12, 2016 | Krell Audio Players & Recorders

2 Answers

Fuses on board blow after a minute or so after power up


Most likely the wire for the speakers, if you have them wired for a specified ohm that the amp doesnt support will cause the issue, as well as bad ground, cross connecting wires. I would start by removing all wires and connections, ensure they are clean and speakers are wired properly.

Nov 19, 2007 | QSC MX1500A 2-Channel Amplifier

1 Answer

Where can I get a fuse for my Krell KSA 300 amplifier.I had a blown fuse on the left channel.


Fuses rarely go on their own. The cause is likely to be a shorted semiconductor device in the left channel output.
Fuses are generally not specific to any brand. Is the fuse a tube with metal ends? If it is measure the length in MM. Then look at the end and you should see the rating. Either in A for Amps or MA for milliamps.
Any electronic parts supplier should have the one you want in stock. Buy several, for if the part I mentioned has gone, it will blow again.

Sep 09, 2016 | Krell Audio Players & Recorders

1 Answer

My GFA 555II amp blew the 2 left channel fuses while playing at normal loudness levels.


Fuses blow when there is a short circuit. All you need to do is replace the main output devices located on the heat sink. They are the ones that will have shorted most likely. Check your speakers and wiring for that channel. Any wire cross connecting will cause that kind of fault, likewise a faulty speaker.
Any engineer will be able to do this job, providing they can find the parts. But you can check them yourself by looking for the parts on the internet.

Mar 03, 2016 | Audio Players & Recorders

1 Answer

How do I brigde a krell show case amp from 5 channels to three channels


Thai will require removal of the top cover to move jumpers or program dip switches in proper order. This will be explained in the owners manual which is located at Krells web site.



Steven Leckrone
The Service Department
30 Unquowa Hill St
Bridgeport CT 06604
203-331-0671
Steven@theservicedepartmentct.com

www.theservicedepartmentct.com

Nov 14, 2014 | Krell Audio Players & Recorders

1 Answer

Channels out of balance - remote will only change left channel.


switch input cables and try this will confirm if the amp has a problem or the input signal

Jun 19, 2010 | Krell KAV400Xi Amplifier

1 Answer

Hello, after plugging on Ipod through my preamp hooked through my krell kav 300 integrated amp I heard a super loud noise and lost power. I examined the fuse and it looks fine. What do I do?


Sounds like the volume was way up when the iPod turned on. iPods are DC and cause a sudden thump through the speakers when they power on.
If the fuse is not blown, there may be another fuse you have not seen. Most amps have three to five fuses especially a 150watt/channel like the Krell.

Apr 17, 2010 | Krell KAV-300i 2-Channel Amplifier

2 Answers

Krell kav300i, increasing volume by itself.


That is an extremely odd problem. I suggest finding a tech in your area who is familiar with the unit, or contacting krell directly.

Sep 21, 2008 | Krell KAV-300i 2-Channel Amplifier

1 Answer

Fuse at power cord blows


first check your speaker cabels for short circuit and speaker for  short coil .after you confirm there is no shotr of cabel wires by checking with avometer in ohm postion.connect speaker if the problem excit your speaker is guilty - change it with same configuration.about switches put it in low order and chech for sound level and you can go up after that.

Mar 05, 2008 | Krell KAV-300i 2-Channel Amplifier

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Krell Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Are you a Krell Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...