Question about Sharp AR-M237 Copier

1 Answer

On a sharp arm 257 can you a drum unit or just blade and drum

What part number for drum unit for sharp arm 257 hard to ti find i can only find drum and blade thank you

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 91 Answers

Did you mean drum frame unit ? This frame include all the spare parts of drum unit except drum and drum fixing plate. The code number is AR 310 DU ( DRUM FRAME UNIT ).

DRUM : AR 310 DR

Posted on Jun 03, 2009


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Model ar5516. Why is drum not cleaning?

Did you prime the cleaning blade with toner when you installed it?, and did you ensure the new cleaning blade did not flip!!!!, re-check the new installed cleaning blade, place a small amount of toner from the toner bottle on the drum along the whole drum. and using your hands at both end of the drum DO NOT TOUCH THE DRUM" turn just a 1/4" CCW (To ensure the cleaning blade is set) then CW to see if the toner is removed. your drum might need to be replaced and or the fuser unit have a example of the copy?

Btw, I’m available to help over the phone in case u need at

Dec 28, 2015 | Sharp Office Equipment & Supplies

1 Answer

Is there a toner catcher tray on this machine or is it trapped in the toner transfer belt?

the toner is flowing in the steps indicated bellow.
1- toner is transfered from the developer to the drum unit. ( the developer wiper blade is responsible for, clogged toner on the surface of the blade is main cause)
2-OPC drum unit. (the opc drum cleaning blade is responsible for this, the aging defect is most, may be the sharpness of the blade is over causing so or the waste toner drive shaft fails which cause back pressure of the toner is responsible).
3- ITB unit, ( the same as drum unit).

Hope rectifying the above may overcome the problem.

Mar 15, 2015 | Samsung Office Equipment & Supplies

1 Answer

Sharp mx-2310u printing double vesion of an image, the copy and the lighter to the right. how can i fix this?

Double print usually happens when Drum completed its life and Cleaning Blade unable to clean the drum surface properly, Replacing of Drum and Cleaning blade will gave you good copy quality, Don't forget to clean Charger unit

Aug 27, 2014 | Sharp MX-2310U Color Printer : 2310U

1 Answer


AR-270NT is no longer accepted by that copier. You must use AR-310NT. Or, you have a bad chip on the back of your cartridge.

May 27, 2014 | Sharp AR-168D Black and White Copier

1 Answer

Error code l 4 01

L4-01 is a main motor lock error. More than likely something is locked up, rather than a problem with the motoer itself. Make sure the drum and Developing unit are turning freely. The Fusing unit binding can also cause this error. Turn the machine off, remove the developing unit and the drum. Put the developing unit back into the machine, close the doors and turn it on. If you can hear the motor run and there is no error code, then the drum is locked up, probably due to a flipped cleaning blade. The next area to check is the developing unit itself. Sometimes if the bushings go bad at the ends of the developer roller, it will cause a motor lock. There is a white coupling on the rear side of the developer unit. Turn it counter clockwise about a half turn, being careful to hold the unit level. There should be little resistance. If all seems O.K., then the Fusing unit is probably the cause. Also pull out the paper cassette and make sure nothing is preventing the pick up rollers from turning.

Aug 02, 2012 | Sharp Office Equipment & Supplies

1 Answer

Como desbloqueo mi fotocopiadora tiene este codigo h4-20. es una sharp arm-257

you have a problem with the fuser unit. Remove unit and check lamp and thermostat. enter sim 14 to reset code.

Jun 10, 2011 | Sharp AR-M257 Black and White Copier

1 Answer

It's a arm 257 copier with a code f5 -02 ran the

clean white surface under the glass and also mirror under the lamp be carefull to lamp

May 21, 2010 | Sharp AR-M237 Copier

1 Answer

Thick black line in all copies on sharp arm 162e

when drum clean blade is weak then strongly can not clean toner,so thick black line in all copies.
Solve: Replace clean blade or service.If your copier drum life is zero,you can change it.

Nov 16, 2009 | Sharp AR-M162 All-In-One Laser Printer

1 Answer

Black blotches and streaks on copies

Sounds like a worn drum unit primarily the cleaning blade on the drum is failing. If you don't change it out soon the dirt escaping from the drum and dirty copies will foul-out you fixing unit, = more $$.

Jul 09, 2009 | Sharp AR-5316 Advanced Digital Imager...

Not finding what you are looking for?
Sharp AR-M237 Copier Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

268 Answers

amir hamza
amir hamza

Level 2 Expert

318 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides