Question about Office Equipment & Supplies

1 Answer

When on Staples SPL-1606X (Cross Cut) Shredder when on ''auto'' mode shredder won't stop after shredding the paper that's been fed in & shred

Posted by on

  • 2 more comments 
  • Anonymous Mar 28, 2014

    I need a user manual for above product

  • Anonymous Mar 28, 2014

    When we insert a piece of paper into the shredder it does not cut at all. It will reverse but won't shred paper. What could be wrong with it?

  • Anonymous Mar 28, 2014

    Will not shred paper. How can I fix this problem?

  • Anonymous Mar 28, 2014

    Shredder will not shred paper at all.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 328 Answers

Make sure there is no paper blocking the sensors. Otherwise you may have a bad sensor or switch.

I’m happy to help further over the phone at https://www.6ya.com/expert/jayw_0e86fb055a7b73de

Posted on Jun 05, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a staples spl-xc200d paper shredder. It runs on auto is that normal


If I understand the question then yes it should run on auto when the paper is inserted to be shredded. I have this shredder as well and mine is always set to auto.

Apr 19, 2017 | Staples Office Equipment & Supplies

2 Answers

How do I fix a staples spl tmc 10 paper shredder that does not feed?


It may be clogged with shredded paper. With power removed, examine the shredding mechanism and remove any bits you find. You may not be able to remove all of the bits but enough to restore operation.

Oct 09, 2014 | Office Equipment & Supplies

1 Answer

I just bought the Omnitech 10 Sheet Cross Cut Shredder. Is it safe to shred papers with staples in them?


I don't have that model but have an 8 page cheapo shredder. It takes CDs, credit cards and staples with no whining.

Oct 23, 2013 | Omnitech 12 Sheet Cross Cut Shredder

1 Answer

Staples Shredder SPL-S302D I think I need a new


Take a look underneath where the shredding mechanism is and remove every bit of paper. It is a messy job, but necessary. When you finish, the shredder probably will function normally. Also, ignore the advertised sheet capacity and feed one sheet at a time. Stop when the bin is half full, dump it, and repeat the bit-by-bit cleaning process. I just went thorough this exercise yesterday!

Feb 16, 2018 | Office Equipment & Supplies

1 Answer

Spl-txc122a


The motor runs reverse even when in Auto mode, how do I fix it, and why did it happen

Mar 27, 2013 | Staples SPL1506X (CrossCut) Shredder

1 Answer

How do you remove the top to see the gears in a Royal 16CDX cross cut paper shredder. The overload message is displayed, and I don't know how to get it unjammed.


a possible solution is to UNPLUG the unit, reach in from underneath and start pulling stuck paper out. On mine (different model) I can remover the paper receptacle bin and reach up to remove stuck paper. this usually is caused by overloaded bin pushing shredded paper back up to cutters because it is overfull......BE SURE TO UNPLUG FIRST !!!!!

Nov 17, 2012 | Royal 160MX Also called 16CDX Cross-Cut...

1 Answer

Tried to clean some shredded paper in the shred area that was stuck, and now shredder won't work.


Disconnect the shredder Turn the top unit over to reveal the 'teeth' With a pair of needle-pointed pliers or cosmetic tweezers gently pick out the pieces of paper that you can see. You'll probably notice that there was some self-adhesive label material included (that seems to cause jamming more than staples!
Hope this helps.
Peter

Apr 20, 2011 | Dynex Cross-cut Shredder

2 Answers

STAPLES TITANIUM CUTTER (SPL-TMC16A) CONTINUES TO RUN WITHOUT STOPPING AFTER PAPER HAS BEEN SHRED. THE FORWARD LIGHT FLASHES.


can't solve the problem, but wonder if I could get an owners manual for this same model (SPL-TMC16A)

Dec 16, 2010 | Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

536 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2239 Answers

Ekse

Level 3 Expert

13434 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...