Question about Jandy 112000 Btu Titanium Air Energy Heat Pump

Open Question

How to fix low coil temperature in jandyair energy titanium pool heater

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Pool heater throws code h5? smoked


HS
Water Temperature Sensing Error

A) Inlet water temperature sensor is reporting a temperature in excess of 104 degrees.
Normal operation resumes 2 minutes after inlet water temperature sensor reports temperatures of 104 degrees or less. This error functions in both normal and remote thermostat modes.
or
B) Inlet water temperature sensor is reporting a temperature change at a rate faster than 6 degrees in 60 seconds, indicating a potentially damaging low water flow conditon. Normal operation resumes when temperatures stabilize. If this condition is detected 3 times, the heater will lock-out until the electrical power is cycled off and back on.

Jun 10, 2014 | Hayward H Series Pool & Spa Heater...

1 Answer

Low coil temperature on jandy air energy titanium pool heater


If this is a problem only when the air temp out side is cooler than normal and your water temp is low, then the unit is performing correctly. The heatpump is having trouble performing with low ambient air temp because when the temp gets to low the coil will ice up.

Feb 16, 2014 | Jandy Pool & Spa

1 Answer

Air energy electric pool heater shows low pressure, low temperature and will not turn on


low pressure will either be gas or water. technician with a manometer can check gas inlet and manifold pressure. ensure adequate water flow from pump. pressure switches generally close at 2psi. you can jump the pressure switch if you think its faulty, or use ohm meter and check continuity of pressure switch

Oct 03, 2013 | Pentair MAXITHERM 333K BTU PROPANE GAS...

1 Answer

H400 manual h400ped2


I have a 2005 Hayward H400PED2, I want to know if it's a titanium exchanger beause I want to add a salt system?

Thanks

May 08, 2013 | Hayward H Series Pool & Spa Heater 400k...

1 Answer

Laars Lite 2 Pool Heater max temperature too low


if hooked to a system increase temp if not try new temp sensor in heater

May 04, 2013 | Jandy Heater Temperature Control Assembly...

2 Answers

Heater reads spa water 15 degrees higher than it is


if a 3 wire system put pool at temp desired and spa at 104 if 2 wire to firemans switch run heater all the way up to 104 the system will control the temp

Feb 22, 2010 | Jandy AquaLink RS2/6 All Button Dual...

4 Answers

Pool and Spa Heaters pros and cons


An electric heat pump needs heat available to pump. If it is 30 degrees outside, heating a spa to 102 or so, may be impossible unless the heater has some type of alternative heat source. A properly sized, gas fired heater can take care of a larger range of heating needs. A combination heat pump and natural gas heater, probably with a controller, really makes the issue more difficult, expensive, and would require a lot of study for efficient, cost effective operation. Bottom line: In really mild climates a heat pump might do the job. In cooler climates the gas heater rules. And where a wide range of temperatures and high heat demand is wanted by the customer, a gas heater is the only way to go. A backup heat pump may take years to payout.

Aug 27, 2008 | Saunacore Special Edition Residential...

Not finding what you are looking for?
Jandy 112000 Btu Titanium Air Energy Heat Pump Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

10764 Answers

Bill Jordan

Level 2 Expert

375 Answers

Steve Slater

Level 2 Expert

72 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...