Question about Kyocera FS-3900DN Laser Printer

1 Answer

7410:0111301 The printer power on and say this error on dispaly.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 41 Answers

Most probably the drum unit has shifted slightly out of position. Remove the toner/process unit, open the cover on the left side of the machine, Remove the waste toner bottle. You will see a grey release button for the drum unit, press it in, slide the drum unit out a couple of inches and slide it back in firmly so that it seats and clicks in completely. Reinstall removed parts. Should be good to go.

Posted on Mar 10, 2014

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

C6000 after changing the toner kit .. the message dispalyed call for service. .. please help


chek your power 110 or 220

220 ok and 10871087 163 exicutive
restart prblm not slvd??
thn chek fuser lamp nd thermistr fuse

May 22, 2012 | Kyocera Mita KM-2550 All-In-One Laser...

1 Answer

I have LL43 on dispaly


If this does not work place a service call.
Power printer on and off. Make sure you power OFF the printer before powering OFF the Controller, and power ON the printer before you power ON the Controller.
  1. Power OFF the printer. The power switch is located directly to the left of where the power cable enters the machine.
  2. If you have a Controller installed, power OFF the Controller. Not all printers are equipped with a Controller. The Controller power switch is located just above the power switch.
  3. Wait at least 10 seconds.

    NOTE: Powering OFF, and then ON again too quickly will result in a software error.

  4. Power ON the printer.
  5. Power ON the Controller.
  6. Switch the A / B button to the ON position. The button will be in the out position and the green light will be ON.

    NOTE: Not all machines have the A / B Switch installed.

Mar 16, 2011 | Xerox 8830 Copier

3 Answers

Just purchased an hp deskjet 3050 all in one and the language on set up initially was accidentally set in spanish and I would like to know how to reset it. The only thing someone could tell me was to take...


1) Remove power cord. 2) Press and hold together Cancel button and OK button ( OK button is the one at the very bottom). 3) Reinsert power cord to rear of printer while holding in both of these buttons for about 20-30 seconds. Make sure power is switched ON 4) The HP sign should come onto the dispaly. This should reset the dispaly screen back to factory settings. You will have to reconnect your wifi again. This worked for me. Good luck.

Feb 27, 2011 | HP LaserJet 3050 All-In-One Printer

1 Answer

Lsu error in dispaly


Hi


Your printers motherboard must be replaced it
the cost of it is to high
You better replace your printer


Pls vote me to keep me alive

Nov 24, 2010 | Xerox PE120i Laser Printer

1 Answer

In dispaly it shows scaner error


This is a known issue with this product.There is no resolution other than to replace the scanner assembly.If the product is under warranty,contact HP and they will service the printer free of charge.

Jan 13, 2010 | Office Equipment & Supplies

1 Answer

Switch works ok but dispalys door open error. this after changed scanner unit


the sensor that is on the left of print is not working. please check that you have correctly install the sensor.

Aug 06, 2009 | HP Color LaserJet 2600n Printer

1 Answer

Error code 21 displayed


1. Function 7
2. Press Monitor 4 times
3. press 7
4. Press 1 to select sub code
5. press 2 you want "LBP Fuser reset"
6. then power off the machine, if the code comes pack you need a new fusing unit(the hot part), the fusing unit is what fuses the toner to the paper, if that didn't happen the toner would rub off when you touch it.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Aug 05, 2009 | Office Equipment & Supplies

2 Answers

Getting error code e000


Mr.Rajonline,how can reset do you know?It is not diagonosis, we want to know how to reset it possible?

Jul 17, 2009 | Canon imageCLASS D760 All-In-One Laser...

Not finding what you are looking for?
Kyocera FS-3900DN Laser Printer Logo

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...