Question about Asko W6461 Front Load Washer
My Asko 6461 washing machine - F3 error message ??
F3 problem, I had the issue on model W6461, however, judging by the amount of F3 issues posted this could work on other ASKO models
If the coin trap in the drain is clear of debris, try this.
Stages as follows:
1) Open drain pump door (bottom left of machine).
2) Remove black pipe and drain residual water.
3) Unscrew coin trap and remove, use a container to hold the water.
4) Leave the container underneath and make sure you have some towels ready (I didn't at the time)
5) Where the washing machine drain hose connects to the outlet in the wall or U bend connector remove this and expose the end.
6) Blow into the drain hose as hard as possible......hopefully the blockage will clear back through the coin trap. 7) Pour some water into the open end and blow this back through the drain as well.
A large lump of sludge, three of my 5 year olds small counter coins and about a litre of water (all over the floor, don't forget the towels!)
Just ran the machine now and fault cleared.
Posted on Sep 13, 2010
Just saved $180 callout fee. Same as above, coin trap was clear but still not pumping water out. I tried putting back through the drain pipe but it just over filled indicating a blockage.
Used a wet/dry vac and some tape to join to the drain pipe and sucked that blockage out, filled machine with water and sucked again to clear. Then did reverse and pushed air through pipe (with coin collector open) and out popped a button plus a lot of black tissue/hair etc.
Put the vacuum on such one more time.
Put all back together, filled washing machine extra fill and ran drain mode. Water hasn't flowed that great since it was new. Might do this annually. now.
Thanks for the tips.
Posted on May 05, 2018
While the instructions for troubleshooting the F3/no drain/pump issue were very clean in the manual I did experience one major challenge..the removal of the interior 'plug' to the pin trap. I was not able to get any kind of grip on the white plastic at all. I was gently inserting a flat head screw driver UNDER the lip of the black gasket but could not get the plug to come out...after about 15 minutes mucking about with two flat heads and managing to scrape out a few coins I realized that the plug was eased out about a quarter of an inch. Using two flat heads on either side (i needed to put something under them at the pivot point to get proper leverage) the plug did come out. For anyone trying this : 1. The interior portion of the plug is an @ 3in long cylinder. 2. The black gasket IS a part of this so if you pry , pry under that. 3. It does NOT screw out, it just pulls and is tightly fitted. It was an exercise in patience. The reward was $5.17 cents in change that was TOTALLY jamming and blocking the pump/drain. running a load now in hopes that this has solved the issue!
Posted on Aug 14, 2016
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Feb 05, 2011 | Asko W6461 Front Load Washer
Oct 26, 2010 | Asko Washing Machines
May 25, 2010 | Asko W6461TS Titanium Stainless Front Load...
Feb 28, 2009 | Washing Machines
Apr 24, 2008 | Asko W6021 Front Load Washer
May 21, 2018 | Asko W6461 Front Load Washer
Aug 06, 2016 | Asko W6461 Front Load Washer
5,097 people viewed this question
Usually answered in minutes!