Question about HP C6280 All-in-One Printer

Open Question

HP PHotosmart 3310 print head alignment error

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: Error HP Photosmart 3310. No strart print, no scanning...

I have a Photosmart C6180 all in one and get an error message 0xc18a0101 Ink System has failed. Unable to copy, receive faxes or print. Refer to printer documentation. Error: 0xc18a101.

I put new cartridges in and tried to recalibrate as mentioned by someone on the board. Can anyone help, please?

Posted on Feb 20, 2008

Ad

Anonymous

  • 2 Answers

SOURCE: hp photosmart error code 0xc05d2381. does this

french oeioe

Posted on Aug 16, 2009

buffalonyman

buffalonyman

  • 1865 Answers

SOURCE: HP Photosmart 3310 All in One - just failed

Go to the following link to get support for your printer

http://h10025.www1.hp.com/ewfrf/wc/product?product=439491&lc=en&cc=us&dlc=en&lang=en&cc=us

Posted on Nov 05, 2009

Testimonial: "Straightforward answer & appropriate link!"

SOURCE: hp 3310 photosmart - ink system failure 0xc19a0013

Ink may be new, but their nozzles may be blocked; depending on manner of storage. To be sure apply a folded tissue paper to the ink nuzzle and press firmly. If the tissue comes off well blotted with ink it means you still have a good amount of ink in it and the nozzle is not blocked. If not blotted or scantily blotted, it means ink is really low or nuzzle is blocked. To be very sure of this, place nuzzle in a plate/saucer with a bit water so that the nuzzle is soaked. Leave for about 10 minutes. Then apply the tissue again. If still not well blotted it means ink is really low or empty. If new you should return it for a replacement. In the case of blocked nozzles, the procedure may be repeated over to get results.
If this doesn't work let me know.

Posted on Dec 20, 2009

pineworks

Clive

  • 4345 Answers

SOURCE: I am getting an error message on my HP Photosmart

Hi

There there to much to tell you what to do but I found a link for you to see it will tell you what to do just click on the link it will take you there.

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01458034&lc=en&dlc=he&cc=il&lang=he&rule=6783&product=3655608
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks


Posted on Feb 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

TobI have a Photosmart 3310 that has been playing up (leaks ink) and occasionally shows an error code Oxb 80e 15be. If I turn the machine on/off it does work again (albeit smudge/streak on underside of...


Good day Steve.
The problem could be just the ink cartridge or the print head itself. Here are a few tips to try to correct this problem.
1.On the front panel of your printer, press Set up softhardware.jpg then press Tools. Choose Align Print head then press OK. Print head alignment will start. You will most probably get an alignment failed. This is already a sign of a hardware issue, in this case the print head.
Or Open HP Solution Center (click Start , click All Programs , click HP , and then click HP Solution Center ). If you have more than one All-in-One installed, make sure to select the correct All-in-One tab in HP Solution Center . Click Settings . Click Print Settings . Click Printer Toolbox . On the Device Services tab, click Clean the Print Cartridges , and then follow the onscreen instructions. Three levels of cleaning are available.
2.Manually check the ink cartridges for any leaks. Reseat each ink cartridge and clean them.
3.Perform a power reset. While the printer is on, unplug the power cable from the back of the printer. Wait for 30 seconds and then powering it back on.
Try to print and if it still the same issue, it is already a print head problem.

Jun 24, 2011 | HP Photosmart 3310 Printer

2 Answers

The black ink on my HP Photosmart 3310 printer does not print. All the colour cartridges print with no problems.


Black printer ink in HP Photosmart may fail to be recognized by the printer. Most times an error message will be sent indicating that something is wrong with the black print cartridge. Sometimes the printer may accept to print with the black ink, but the printouts may have horizontal lines and very illegible letters. In such a case a manual cleaning of the print head should be carried out. In doing the manual cleaning, one should spray Windex heavily on paper towel and wipe off the surface of the print head.




Sep 14, 2010 | HP Photosmart 3310 Printer

2 Answers

Colors do not print right. We have tried to align, calibrate, and clean the heads, and the colors went from too much purple, to too much magenta


This would need a print head replacement kit there around $40 bucks from the mnaufacture. The issue here is the mix of the colors and this is caused by the print head.

Thanks I know this will help if you follow threw please do leave ratings and feedback

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/edwy_1a56970cf1ea4620

May 10, 2010 | HP Photosmart 3310 Printer

1 Answer

Hp photo smart 3310 all-in-one


You need to check your printers nozzles. Should find it under Properties of the printer and then you can select clean nozzles where you printer will clean the nozzles. Also do a Head alignement.

Oct 05, 2008 | HP Photosmart 3310 Printer

1 Answer

HP Photosmart 3310 All iN One Printer


Try taking out the ink cartdridge and looking at the contacts where the ink cartdridge meets te cradle, sometimes ink gunks up on the carasel and allthough you change it out, the gunk stays there and just block the new one put in. wear latex gloves when doing this, Black ink is pesky on the skin.

Also, just might want to check the printer settings and be sure it isnt set to print in greyscale.

Nov 14, 2007 | HP Photosmart 3310 Printer

Not finding what you are looking for?
HP C6280 All-in-One Printer Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...