Question about Fisher and Paykel WA37T26G Top Load Washer

1 Answer

What do I do if the control pad does not work?

Power to socket is on. Disconnected plug from socket for a few minutes. Plugged back in and nothing. No response to pressing Power button.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Fisher and P... Master
  • 745 Answers

Top loader ?
if so burnt out pump if gd blown main computer module

Posted on Apr 21, 2018

Ad

2 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
caroldon

Donald DCruz

  • 17130 Answers

SOURCE: Fisher and Paykel Washing Machine

Assuming that the machine was unused for a period of time , please allow to have the washer plugged on to remove any traces of moisture on the machine's circuitry while it was in transit.
Also if there was any corrosion in the motherboard as it was off circuit for a long time, this might happen.
If there is no result after keeping it ON for several hours, Unplugging and resetting once again then the main controller board , connectors and wires must be checked for possible damage during transit.
It will be good to have the set removed out , looked into carefully for any such breakages, reconnect all the wires to notice any change.
Please try these tips and respond.

Posted on Nov 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Finlux c13 dishwasher no lights coming on and won't work I have changed the fuse in the plug and no diffidence still nothing happening does anybody know what it might be Thank you


If it's hard-wired into the house wiring, turn off the breaker that controls it for 2-3 minutes, then flip back on. It might recycle and power up. If plugged into a wall socket, unplug it for 2-3 minutes, then plug back in. OR there may be a reset button somewhere on the unit. Consult your manual.

May 23, 2016 | Dishwashers

1 Answer

My ASUS Transformer will not power on


1. Make sure it is charged. If the battery is dead you may need to leave it plugged in for a few minutes before it will turn on.
2. Hold the power button down for at least 10 seconds. This may bring it back to life if it didn't shut down properly.
3. Make sure no other buttons are stuck down (volume up or down). If another button is stuck down the power button won't work.

Apr 16, 2013 | ASUS Eee Pad Transformer TF101A1 Tablet...

1 Answer

My machine is not getting any power. I took my machine to a class yesterday. It worked fine but when I plugged it in here at home last night, nothing happened. I checked the outlet with a lamp and the...


it is possible the power cord has gone out,,or the power cord receptacle has gone out
i've been working on a sewing machine that they connected the power cord & disconnected it so much that they pushed the pins out of there sockets

or the on/ off switch has gone out

Nov 19, 2010 | Brother Sewing Machines

1 Answer

I was able to charge it fully last night but now it will not turn on this morning.It is a sansa clip i have tried holding the power up for a few minutes but still nothing.


I'm surprised it wouldn't turn on when plugged into external power. That would mean a different problem than a disconnected battery lead ... possibly a disconnected USB port lead, though then I would have expected that you'd be able to turn it on when not plugged in.

Feb 19, 2010 | SanDisk Sansa Clip MP3 Player

2 Answers

Error message on Kenmore oven


F-1 is not good. It basically means the EOC (electronic oven control is bad). There is a little test here for a little info:

This simple test will help determine whether the ERC (Electronic Range Control or Clock) or the touch pad is defective when F1 error code is present.

Note: Some models incorporate the touch pad in to the ERC as a single assembly, in which case this test is not necessary. Simply replace the ERC (Clock).

Warning: If you feel in any way uncomfortable performing this test or making this repair, please contact a qualified appliance repair technician.

1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing.
2. Gain access inside the control panel.
3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.
4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.
5. Turn the power back on.
6. Wait for at least one hour to see if the F1 code comes back (usually accompanied by a beeping sound).
7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.


If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Sep 04, 2009 | Kenmore 40494 / 40495 / 40499 Electric...

1 Answer

The display at top of stove is showing "F1" and continuously beep


Maytag Range / Stove / Oven Fault Codes Failure Code Fault Code Description Solution F0 Function key stuck Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). F1 Defective touch pad or clock (ERC) Replace touch pad or clock (ERC). Touch pad is a more common problem. Refer to F1 test at the top of this page for more information. F2 Oven temperature too hot Replace relay board, if present, or oven temperature sensor (RTD). Check sensor harness. F3
or
F4 Shorted or open oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok. F5 Watchdog and hardware conflict Replace clock (ERC). F7 Function key shorted or stuck Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). F8 Analog / Digital problem Replace clock (ERC). F9 Door latch Check door latch components.

Mar 19, 2009 | Maytag PGR5710 Performa Gas Kitchen Range

6 Answers

New heated mattress pad won't warm up. Controls keep blinking.


i've lost my control for a king size electric blanket. it had dual control-can u tell me where i can get one and the cost. thx

Dec 13, 2008 | Sunbeam SG7621SP Grill

1 Answer

Setting the clock


Remove the plug from the socket for a few minutes. Then plug it back. Does the clock control blicking? look at the pictures on the control as a whole.
Do you see anything like a table clock? press it once, then press the numeric pad or up and down arrow button depending on the model you have. press enter or start if set correctly.

Jul 24, 2008 | KitchenAid KGST307 Gas Kitchen Range

25 Answers

Wii / No Power


or you can remove all of the plugs from the console: AC, remote sensor, AV. This is important: You must also unplug the AC from the electrical outlet. Then wait 45 seconds, then plug the AC adapter back into the wall and your console. Power On.

Dec 25, 2007 | Nintendo Wii Console

Not finding what you are looking for?
Fisher and Paykel WA37T26G Top Load Washer Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

peter gittos
peter gittos

Level 2 Expert

247 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...