Question about Krell Audio Players & Recorders

1 Answer

Krewll showcase processor right channel noise is coming after one hour

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 42 Answers

Chances are that you have a "Leaking" capacitor in the final stage.

Time for the repair shop :(

Posted on Jun 14, 2014

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crackling noise all channel when i change 110v to 220v


Sound as if you have a low voltage, check for 220 v if its ok, then you have a current problem, the higher the voltage, it will be less current flow. Hope its not a flaw on the 220 v side

Dec 20, 2013 | Krell Showcase 5 5-Channel Amplifier

1 Answer

Amp schematic diagram channel


Iwant the schematic manual for krell showcase 5 ... tank you ...

Dec 20, 2013 | Krell Showcase 5 5-Channel Amplifier

1 Answer

Getting a lot of noise from new Aphex Channel Master Preamp how do I fix this? I was using a Neuman TLM 103 mic and just recently switched to a Rode Procaster mic but still plenty of noise. I'm sure...


My thought is that this is a gain issue. Too much somewhere, and not enough somewhere else. Try experimenting with the input gain on the unit, and your mixer until you can reach a better noise floor. Otherwise, some units are noisier than other brands inherently. But experiment and see what you come up with. Also check for the +4 or -10dB switch. If there is one, it may be set incorrectly.

Apr 25, 2013 | Aphex Channel-Master Preamp and Input...

1 Answer

I have a Static noise coming from the right channel of my mixer. I hear it coming out the right speaker as well as the right ear of my headphones (jack). How can I fix this?


That sounds like a bad connection but it can also indicate your mixer has a problem. If it occurs on all channels it is the mixer, if only one then the problem is in the input. Check your cables, they are a big culprut in problems like this.

Jan 08, 2013 | Stanton SA-5 DJ Mixer

1 Answer

Main menu screen won't stay up on my krell showcase


If the main menu comes and goes off then it is possible that there is a fault in the processor memory. Try and reset with the given code- refer to manual, if not switch off set for about 6-12 hours and press down the panel buttons to drain off all residual voltage . this might help to reset.

Jun 06, 2012 | Audio Players & Recorders

1 Answer

Main menu screen won't stay up


I have answered this fault earlier , please check this out

Jun 06, 2012 | Krell Showcase Surround 8-Channel...

1 Answer

How to connect effects processor to mackie 1602 mixer


Should be an Aux 1 or 2 output jack on the right side of the mixer. You can come out of the 1 or 2 OUTPUT jack to the input on your processor, and then from the output of the processor to Effects return or to a channel input. By going to a channel input you can then blend the processor's signal with a slider into the sound system with the other channels, while adding tone if needed. By going back into the Effects return, you just blend it overall by adjusting the Effects return knob.
To feed the channels through the processor, turn the AUX 1 or 2 knob up on each individual channel you want to go through the processor. Make sure the AUX 1 (or 2 if you are using that) MASTER knob is turned up on the right side of the console, otherwise nothing will go to the processor. You should see the processors' input light showing signal, if not check your connections. Good luck

Feb 19, 2011 | Mackie 1402-vlz3 Compact Mixer - 120v

1 Answer

Left from speaker not working- Yamaha HTR-5940-6.1 channel


Redbird,

What do you have in the "multi channel input" jacks on the rear of the receiver? Those inputs Right, Left, Center, Surround R+L, and Sub are used when selecting 6 channel mode. They bypass the receivers surround processor board.

John W

Jan 10, 2009 | Yamaha HTR-5940 Receiver

1 Answer

Drop out of left channel, Adcom GFA5802


It sounds as if there is a broken solder joint somewhere that slowly opens up with heat. The other possibility is that an input or driver transistor is dying. Since the whole channel is dying, I would guess the broken joint and/or dying transistor are near the very input of the channel.
A tech can very easily find the spot by playing the amp until it starts to die, then spraying small bursts of freeze spray, one component or area at a time, until the amp suddenly comes back to life.
 

Aug 13, 2008 | Adcom GFA-5802 2-Channel Amplifier

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Krell Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

Gil Shultz

Level 3 Expert

3388 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Are you a Krell Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...