Question about Hotpoint 21.7 cu. ft. Side-by-Side No-Frost Refrigerator with Dispenser CSX22GRBWW

Open Question

How do I fix door hotpoint CSH22GRTA?

There used to be more tension on the door, now it swings open too easily and slams into the cabinet. How do I fix this?

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

mike cooper

  • 884 Answers

SOURCE: need gaskets for CSX20E Hotpoint side by side

Seals don't lose their magnetism. Check the door closes all the way round and adjust the hinges if it doesn't sit straight. Check there isn't a relief valve frozen up or blocked (it allows air to escape when the doors are closed). Check the drawers are fully pushed back in and not stopping the door closing properly

Posted on Sep 12, 2012

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Add tension to loose oven door amana gas model args7650ss


Hello. You will need to replace the door hinge assemblies. The part numbers are as follows:
Right hand hinge 31715202
Left hand hinge 31715201
I hope this helps you.

Aug 14, 2015 | Amana Kitchen Ranges

1 Answer

Hotpoint wm64s indicating door not shut program will not function cus door light flashing...however door iis shut n wont open


You have a mildly confused machine, probably the result of the fact that there is a moment where the door lock can activate, but the sensor that tells if it's shut cant because the door isn't QUITE pushed home hard enough.

First try, just give the door a whack with the heel of your hand in line with where the door catch is. It may be that simple to relocate the door and the sensor properly

Failing that, unplug at the wall and wait 20 minutes. This will, without doubt reset the machine and allow you to open it (While it is still powered off!). Open the door and shut it firmly.... I hesitate to say SLAM the door.... But slam-ish won't hurt, just don't be stupid about it!

All should be OK going forward

Jul 04, 2011 | Hotpoint WMA64 Front Load Washer

1 Answer

How to fit a belt to a hotpoint v3d01 dryer


Instructions

Tools Needed:

Screwdriver

Hand vacuum

1. Unplug the electrical cord of the Hotpoint tumble dryer from the electrical outlet before attempting to replace the belt.

2. Pull the door open on the dryer and locate the screws on the underside of the top cover. Unfastening the screws with a screwdriver.

3. Flip the top cover back so that it rests on the rear hinges, and find the screws on the top of the front panel on the inside of the dryer cabinet.

4. Undo the screws on the top of the front panel with a screwdriver, and tilt the panel away from the dryer cabinet. Unplug the door switch connector from the metal prongs on the back of the front panel.

5. Lift the front panel up and remove it from the dryer cabinet. Set it out of the way. Locate the idler arm and motor on the bottom of the cabinet.

6. Move the idler arm forward to relieve the tension on the belt, and take the belt off the idler arm and motor pulley as well as from around the drum.

7. Place the new belt around the drum, looping it over the idler arm pulley and around the motor pulley. Move the idler arm back into place to add tension to the belt.

8. Verify that the belt is lined up correctly with no twists in it, and put the front panel back on the dryer cabinet. Plug the door switch connector into the metal prong on the back of the panel by hand.

9. Secure the front panel with the screws at the top, and flip the top cover down over the cabinet. Secure the top with the screws on the underside of the front lip.

Feb 23, 2011 | Dryers

1 Answer

Door has been an issue when closing light stays on and you really have to slam the door for the light to go off


Door catches.

Remove from any power source, remove the cover of the cabinet. Slacken off the clamp mechanism and ease the clamp over the guide to allow the door to open. The door may be easily adjusted by slackening off the screws that clamp the door catch/actuators in place whilst holding the door closed and then tightening the screws. The rear of the door may be adjusted by slackening the lower door hinge screws and adjusting as required.
I hope that helps.

Jan 24, 2011 | Whirlpool GH4155XPS Microwave Oven

1 Answer

My dryer starts to squek real loud when it is running


The source of this noise is usualy the dryer drum drive belt.
  • Unplug the electrical cord before replacing the dryer belt.

  • 2

    Pull open the dryer door and locate the screws underneath the top lip that secure the top of the dryer.

  • 3

    Unfasten the screws holding the top on with a screwdriver and lift the top, flipping it back and resting it on the hinges.

  • 4

    Unfasten the holding the front panel on the cabinet, using a screwdriver. These screws are at the top on the inside of the panel.

  • 5

    Disconnect the door switch wires on the back of the front panel by hand, pulling the connector straight out off the electrical prongs and setting the front panel aside.

  • 6

    Locate the idler arm pulley next to the motor on the bottom of the cabinet near the back and push the idler arm forward to relieve the tension on the old belt.

  • 7

    Remove the old belt from around the idler and motor pulleys as well as from around the dryer drum and take the belt out of the dryer cabinet.

  • 8

    Place the new dryer belt around the drum in the center of the cabinet, fitting the belt inside the V-groove in the center of the drum, and lay the rest of the belt on the bottom of the cabinet near the idler pulley so you can access it easily.

  • 9

    Move the idler arm forward to allow room for the belt and thread the end of the new belt around the idler arm pulley and over the motor pulley, letting the idler arm move back to apply tension to the new belt. Check the new belt over to verify that it is lined up correctly in the V-groove on the drum and around the pulleys and that there are no twists in the belt.

  • 10

    Place the front panel back on the dryer cabinet, securing it with the screws on the top of the panel with a screwdriver, and plug the door switch wires back into the electrical prongs, pressing the switch wires on by hand on the back of the front panel.

  • 11

    Lower the top of the dryer back down onto the cabinet and secure it with the screws underneath the lip of the front panel.

  • 12

    Plug the electrical cord of the Hotpoint dryer into the electrical outlet.

  • Dec 28, 2010 | Hotpoint Dryers

    1 Answer

    Is it possible to reverse door swing on dryer? My daughter has a new Elite front load dryer that swings from left.


    REVERSING DOOR SWING
    Your dryer is designed so the door swing may be reversed at any time without additional parts. Conversion is accomplished by transferring hinges to the opposite side of the cabinet.
    To change the direction of the door opening:
    1. Open the dryer door. Remove the four hinge hole plugs from the left side of the door opening. Place nearby for future installation. NOTE: You may need a plastic knife to help pull out the plugs. Be careful not to scratch the paint.

    2. Remove the four screws that secure the door hinges to the dryer front panel (see below). NOTE: Remove one screw from each of the two hinges first. Hold the door firmly before removing the last two screws.

    3. Rotate the door 180° and reinstall the door hinges to the dryer front panel with the four screws.

    4. Install the four hinge hole plugs in the open screw holes on the right side of the door opening.

    Hope this helped Tim

    Dec 01, 2010 | Kenmore Elite HE4 Electric Dryer

    1 Answer

    How do I get to the motor of this dryer? Do I need to get to it from the front of the dryer or the back?


    On a rear control LG, from the front. Open door, remove two phillips screws at 4 and 7 O'clock positions, use putty knife to push in clips (2) holding top at front, swing top back, remove two phillips head screws holding front panel cabinet. Disconnect door switch and light plugs, tilt front panel forward and off bottom tabs, allowing sensor at bottom to be un-plugged, thus front panel now completely free of machine. 4 phillips screws hold front bulk head / front drum roller supports to cabinet. Lift up and off. Reach in and remove belt from tension pulley. Drum comes right out, allowing access to motor.

    Jun 13, 2010 | LG DLG3788W Gas Dryer

    1 Answer

    My frig door free falls open and then slams into an adjacent cabinet.................making a slamming sound. I had the cam replaced at the bottom of the door about one year ago. The repair man came back...


    You need need to level you refrigerator or possibly have an ever so slight tilt backwards to ensure the door closes when one lets it go and this would stop the swinging outward motion also. Just to be on the safe side make sure you magnetic door seal is hitting evenly on the frame as to make a nice seal.

    Good luck and I hope this helps,
    Robert

    Oct 12, 2009 | GE Refrigerators

    2 Answers

    Where do I find the heating element in my hotpoint dryer


    Heating element is behind the drum. Disconnect power. Use putty knife to release 2 spring clips holding top at front edge of dryer. Swing top back. Remove two screws holding dryer front to sides near open top. Swing dryer front to the side. (you don't have to disconnect the door switch wires) Remove plastic tub block at top center of opening. Release belt. Pull up on back of drum, then pull drum out through the open front of dryer.

    Sep 12, 2008 | Hotpoint NLL113EYWO Electric Dryer

    1 Answer

    Hotpoint ultima washer dryer


    isolate from mains. undo door gasket and check interlock id ok. interlock is mounted on cabinet on rhs

    Mar 11, 2007 | Hotpoint Ultima WD72 Front Load...

    Not finding what you are looking for?
    Refrigerators Logo

    Related Topics:

    63 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hotpoint Refrigerators Experts

    John Tripp
    John Tripp

    Level 3 Expert

    4656 Answers

    jasbo
    jasbo

    Level 3 Expert

    2239 Answers

    jdthefixer

    Level 3 Expert

    746 Answers

    Are you a Hotpoint Refrigerator Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...