Question about HP 1050 Plain Paper Inkjet Fax

1 Answer

Errors with my Printer/scaner

Following errors, Paper jam tried blowing air, cleaning the rollers (hard to clean no back to take off to get in there) also ink error/damaged error took them out looked at them look fine they are band new. so ... ? Tried all the steps in the HP website to get it to print will not print a test page at all, will only grab paper a little and then it stops. Power button blinking. Have Windows 8 This worked fine in Windows Xp. Please help!

Posted by on

  • 2 more comments 
  • Jessica Salmonson
    Jessica Salmonson May 31, 2014

    This my printer I tried to get your HP Deskjet 1050 All-in-One Printer - J410

  • Jessica Salmonson
    Jessica Salmonson May 31, 2014

    to post that but it woud not

  • Randy Schumann
    Randy Schumann Jun 01, 2014

    Jessica: OK, you reloaded the printer driver and looked really carefully at the paper pick-up area as well as cleaning the pickup and feed rollers. Pull the ink cartridges and gently scrub the metal contact plate with a clean rag and a little alcohol. Look in the machine where the ink cartridges fit and you will see the metal contact plate that each cartridge contacts. Clean them also.

  • Randy Schumann
    Randy Schumann Jun 01, 2014

    Sorry for the interruption... Make sure that the ink cartridges are NOT refills, but new HP cartridges. Each manufacturer uses ink cartridges that have a specific electrical current capacity, and many times, a refilled cartridge will have the wrong ink. If the incorrect ink is detected by the machine, the printing process will stop, and the sensor flag will detect the sheet of paper while the machine is stopped and give a jam message, so try working with genuine Hewlett-Packard ink cartridges and clean the ink cartridge contacts in the machine... I'll check back to try any other solutions if that doesn't work. R.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 408 Answers

Jessica:

This could be one of a few things... First, Windows 8 is a completely different animal from Windows XP! Try reloading your printer driver in Windows 8. If this doesn\'t work, you need to clean the paper pickup rollers at the front of the printer (where the paper first feeds into the machine. I use a Q-tip moistened (not sopping wet) with rubbing alcohol... gently scrub the whole pickup roller and then the feed roller next to it. Check carefully (with a flashlight) for any shards of paper that might be blocking the paper path. There is also a sensor flag (small finger of plastic) sticking up that the paper must hit to let the printer know that the paper is feeding through. If you do not see the sensor flag, it is either jammed or has been broken off when a piece of paper was pulled backward out of the paper feed area. First reload the printer driver, and try to print. If it doesn\'t print, check and clean the rollers and look for the sensor flag.

Posted on May 31, 2014

Testimonial: "Thank you I tried all of what you said it it STILL will not print will not scan error paper jammed error or ink error. Every day that this thing is not working is another day were I'm not earning anything I Have to be able to scan my art work, and print out things. There is nothing jamming the printer I have looked the ink cartrages are brand new i feel that my printer is not reading things correctly and is giving these errors, because it does not have an error to go with whats wrong? Have had actual jams before it's not acting the same way, can't put my finger on it."

  • Jessica Salmonson
    Jessica Salmonson Jun 03, 2014

    Have Original ink not refills. still not solved. i\'ve come to the conclusion that it\'s not compatible with windows 8 I\'ve had this printer/scanner/copter for about 11 years. :P Along with finally finding in the HP website that there are no driver updates for this computer for windows 8. So pretty much im with out one for a while *sighs* Also this is my priner this site does not have it on the list of ones to choose from. HP Deskjet 1050 J410 series it\'s around 11 years old now. This "lovely" litter only has a cuddy flap undr it to pull out any paper so pretty much theres no way to get in teh thing to relly check things. :/ all seamlessly one pieace around the sides.

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Printer either has a paper jam or error out of paper when the tray is full


Then have tech come out and look at it sound like a sensor is bad and ore the rollers are dirty that sound you hear is a clutch turning do not continue to do that

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Apr 22, 2015 | Office Equipment & Supplies

3 Answers

Document feeder jams. display says "paper too long".


you may want to check on the paper size and make sure you are using the same one as that of the one of the tray...

Oct 03, 2008 | Canon imageRUNNER 1630 Copier

2 Answers

What is code error e03


Printers & Copiers
Code error E03

Nov 14, 2014 | Office Equipment & Supplies

1 Answer

HP Deskjet 1050 J410 series errors!


Try to factory reset the printer following the OM for the model.

Jul 02, 2017 | HP 1050 Plain Paper Inkjet Fax

1 Answer

I have a HP LaserJet 1312nfi that is giving me a FALSE paper jam message. I repeat - FALSE PAPER JAM IN BACK DOOR. False false false. I have uninstalled it on my computer and nothing. I have opened it...


Hello Chris! Welcome to FixYa!

If you are facing False Paper Jam error in your HP Laser Jet 1312nfi but If you cant see any obvious paper jams, try to look closely into the rollers or the inside. There could be some tiny paper shreds stuck within those rollers. Or there could be a tiny piece of paper blocking the printer's sensor and thus giving you a false paper jam error.
The rollers should be cleaned if the paper fails to feed smoothly into the unit. All document and media rollers should be cleaned using a lint-free cloth lightly moistened with water.

1. Turn Off the printer and unplugged power before cleaning the rollers. This will allow the rollers to be turned by hand in most cases.
2. Remove the rear access door to access the rollers. Clean any dust and debris from the rollers.
3. Open the back of the printer and check metal paper rollers (not the rubber rollers) in the interior of the printer. They should be clean and move freely. If these are not bright and shinny or have buildup on them, they should be cleaned. Also clean any dust and debris off of the rubber rollers.
4. Close the back cover and reattach the rear access door.
5. Plug the power cord back in and power the unit up. It should reinitialize for about 20 seconds.
6. Print another extended self-test page.
After following these steps carefully, False Error message will be disappeared.
I hope this solution helps you
Let me know if you have any confusion in your mind.


Sir, Your Rating as FIVE Stars for this solution and words of appreciation will be esteemed

Thank You for taking my service


Concerned: Muhammad Uzair

Jan 10, 2012 | HP Officejet Pro L7680 All-In-One Printer

2 Answers

My paper is getting stuck on roller for laser printer scx-4521F, when remove paper and open door to reset printer, paper goes through and then jams again on new job.


open the front door and take the cartrige out.
if it jams at the black roller. you must clean the pickup roller.
you will see it at the back of the unit in the center.

Nov 11, 2009 | Samsung SCX 4521F All-In-One Laser Printer

2 Answers

While printing with OKI C5600 very often error message pops up about jammed paper though no REAL jam happened. To solve I just open and close paper tray and front door. JAM PAPER error is real pain if...


Have you tried cleaning the paper feed roller(s)? Either soap & water OR isopropyl alchohol with a cotton ball will do, just make sure the rollers are dry before trying to print again, otherwise damage to imaging unit (drum/toner unit) could occurr. If the printer doesn't feed in the first place, the printer thinks it has a jammed paper, thus opening paper tray and front cover resets misfeed/ jam condition. Let me know your progress....Tim

Oct 24, 2009 | OKI C5500n Printer

1 Answer

Sencor problem


Pull the paper tray out and look inside.You'll see the feed roller.It needs to be cleaned with alcohol or water.Usually,paper dust on the roller causing it to loose friction and it starts slipping during paper feed,and printer jams.

Oct 08, 2009 | Samsung CLP 300 Laser Printer

1 Answer

Hp 4250 tn when i try to print get an error 13.05.00 papper never makes it though the fuser


Error message means "Media is jammed at the specified location (and possibly at other locations). If the message persists after all jams have been cleared, a sensor or sensor lever might be stuck or broken."

For all jam messages, do the following: 1. Remove jammed print media from the specified location. Check the entire paper path for other pieces of media in the path. 2. Open and close the top cover to clear the message. 3. Check sensors and flags in the paper path for proper operation.

Try cleaning your feed rollers...
There are two types of rollers in printers: hard plastic and rubber. Plastic rollers can be cleaned with alcohol (isopropyl). Rubber rollers can be cleaned with a rubber roller cleaner and restorer like the one in the link (you can find other brands, but make sure its for rubber).

http://www.lmcomp.com/80008.html

Jul 27, 2009 | HP LaserJet 4250n Printer

1 Answer

Samsung 3561ND fails to print double sided.


Do you use the duplexer a lot? It sounds as if the rollers inside need to be cleaned. I don't recommend doing this yourself as it involves lifting the printer off of the duplexer, and I don't want to be responsible if you accidentally drop the printer or you or someone gets hurt. But that's how to get to it; the offending rollers should be visible, and may be cleaned with a clean rag moistened with a multi-purpose cleaner. Alcohol is what's recommended, but I shy away from it as it's known to dry the rubber, and all you want to do it clean the built-up dirt and paper duct off of it. Let me know how it works, if you do it! If you opt not to, call a qualified printer technician.

May 02, 2007 | Samsung ML-3561ND Laser Printer

Not finding what you are looking for?
HP 1050 Plain Paper Inkjet Fax Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...