Question about Samsung CLP320 AllInOne Laser Printer

Open Question

Problem with Ghosting on printed page - Samsung CLP320 AllInOne Laser Printer

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hp 8000n is ghosting excess toner on prints. Why?


Perhaps, but first clean up the exposed parts of the printer where the toner may travel before it makes contact with the paper. Also, the fuser may need to be cleaned or replaced. Post your problem directly with HP on the HP website.

Feb 16, 2013 | HP LaserJet 8000n Printer

1 Answer

Ghosting


Normally ghosting is caused by a bad fuser.
Put paper in the manual feed tray(tray 1)
Print something. As the paper gets 1/2 way into the printer, open the cover..
Look at the paper. If there is no ghosting, the fuser is bad. If there is ghosting, could be a cartridge drum.
Follow these steps print a Print quality troubleshooting page to identify which print cartridge is causing the issue.
  1. Open Toolbox .
  2. Click the Help folder, and then click the Troubleshooting page.
  3. Click Print , to print the page. The page prints five bands of color, which are divided into four overlapping sections. By examining each section, you can isolate the problem to a particular print cartridge. Figure 4: Print quality troubleshooting page bandsc01417618.gif 1 - Yellow 2 - Cyan 3 - Black 4 - Magenta

May 01, 2011 | HP LaserJet CP1215 Color Printer

1 Answer

Ghosting


fuser could be faulty

Jun 12, 2009 | HP Color LaserJet 2600n Printer

1 Answer

Ghosting on HP2015 Printer


Hi gpeirce:
Ghosting is the result of a worn fuser assembly. Try to print a half page by printing a document and then try to open the top while the paper is going under the toner cartridge. You have to listen to the paper moving through the paper path.You will see that the paper has print on it but not the hole document. This will tell you if the toner cartridge is bad or the fuser assembly.

Hope this helps

May 30, 2009 | HP LaserJet P2015dn Printer

1 Answer

Ghosting on prints


Wrong paper type can cause this, also if it is damp or too thick. Also check that you have the correct type of paper (thickness) selected in the driver. Ghosting can also be caused by a faulty drum unit, since you just replaced it maybe there is warranty left on it?.

Good luck!

May 24, 2009 | Brother HL 5140 Laser Printer

1 Answer

MY HP LASER JET 2420DN IS gHOSTING DOWN THE LEFT SIDE


The ghosting is most likely the toner or the fuser

This is the test to determine toner or fuser issue.
Print a test page
When you hear the paper feed into the machine open the top or front to stop the machine
Remove the toner cart.
You should be able to see the page with printing on it. (This is before the page hits the fuser)
If you can see the defect on the page the problem is most likely the toner cartridge but NOT the fuser.
If the page is clean the problem is most likely the fuser.
Hope this helps

Mar 25, 2009 | HP Office Equipment & Supplies

1 Answer

HP Laserjet 2420dn - Faint ghosting of printed matter above & below actual print. Have tried cleaning page twice but no better Grateful for any suggestions


  • Please perform a half page test, by printing a test page from tray 1.
  • Open the top cover as soon as the paper is 70% through from tray 1 so that the media
  • Check if the ghosting appears, if yes, fuser needs swap out.

Oct 30, 2008 | HP Office Equipment & Supplies

1 Answer

Magicolor 2300dl ghosting and smear - black only


if only black does that, then it can be black toner, but the best way to find out, print something and when printer starts to take paper open front door, remove waste toner box and take out pc drum and transfer belt and check the printed page from there, if it seems ok, print nex page and open door when page comes out from fusin unit, if quality goes bad before fusing unit, it may lead to 2'nd transfer roller / pc drum and transfer belt quality was ok / if after FU then you have a problem in fusing unit.

Apr 01, 2008 | Konica Minolta magicolor 2300DL Laser...

1 Answer

Xerox DocuPrint P8 Laser Fuzzy Printing


Maybe a bad fuser . That would cause ghosting and reprint on the page

Feb 02, 2008 | Xerox DocuPrint P8 Laser Printer

Not finding what you are looking for?
Samsung CLP320 AllInOne Laser Printer Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1363 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

jasbo
jasbo

Level 3 Expert

2239 Answers

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...