Question about Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Open Question

Cancel button starts drain pump - Whirlpool 24 in. GU3200XTP Built-in Dishwasher

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Philip

  • 949 Answers

SOURCE: whirlpool model du1100xtpq6 machine will not

Hi, this is an indication that the water did not heat properly. Follow this link to some instructions I put together to help solve this and reset the control so you can use the machine again.

http://www.fixya.com/support/r4628906-flashing_or_blinking_green_clean_light_7

Posted on May 08, 2010

Ad

adrian halligan

  • 1075 Answers

SOURCE: dishwasher wont drain

drain pump gone replace.adrian,,,,,

Posted on Jul 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is there water standing in the bottom of my dishwasher after it has completed the wash and dry cycles.......


If water remains in the dishwasher after the cycles end, check the kitchen sink drain to make sure it's not clogged. If there's no clog, try pressing the Cancel button; most dishwashers run the drain pump when the Cancel button is pressed.
Check the dishwasher drain line, drain path and drain pump.
1396454190772-ic2agsuhdt5a3e2mib5hbxs3-4-0.jpg

Oct 25, 2017 | Dishwashers

2 Answers

Dishwasher starts on its own (no house is not haunted). Start resume button flashes


have a service technician in as it appears to be a problem in the program board
could be moisture across the circuit board

Feb 06, 2016 | Maytag MDB7749AWQ Builtin Dishwasher

2 Answers

Water is not drained from the tub when washing of the dishes is complete


The filter is probably blocked.


It is inside the base of the machine.


Take out the filter and clean it and also clean out the filter well as that can also hold quite a bit of debris.



---


Please dont forget to vote if you liked my answer


thanks

------

Feb 13, 2011 | Bosch SHX45P05UC Dishwasher

1 Answer

Kitchen aid dishwasher not draining....help


Hi,
Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...

Dishwasher Problems - Water will not drain out

heatman101

Apr 05, 2010 | KitchenAid 24 in. KUDM01TJ - Multiple...

1 Answer

GET ERROR CODE f-2, AND IT WONT DRAIN THE WATER kENMORE ELITE hE3T


It is a code for a long drain problem (more than eight minutes). Press the Pause/Cancel button twice to clear the display. When the display is clear, press the Drain & Spin button then select No Spin by pressing the Spin Speed button, and then press and hold the Start button to start draining the water.

Use your senses to check whether the drain pump is running or not. The drain pump is located at the front right bottom of the machine. Check the volume of water being discharged to the drainage.

Disconnect power to the washer and check the drain hose for clogs and kinks, and then repeat the No Spin draining process, if the drain pump is running and water is being pumped out, until the water is completely drained out of the washer. Just press the Pause/Cancel button twice when the code appears to clear the display and restart draining.

Make sure the drain hose is raised no more than eight feet above the floor where the washer is installed. The drain pump cannot pump the water properly out to the drainage more than eight feet above the floor.

When draining is complete, empty the machine then prop up the bottom front edge of the washer to allow easy access to the three screws attaching the lower front access panel to the cabinet. Remove the screws, and then push the panel down and off the cabinet to access the drain pump.

Place a shallow pan or lay a towel under the filter to catch the water from the pump. Unscrew the filter from the pump assembly and drain the water. Clean the filter for any debris that might be causing the pump to work poorly then screw it back in place.

Slide the lower front access panel up back into the cabinet and secure it the three screws.

Mar 12, 2010 | Washing Machines

1 Answer

Water in dishwasher


if you push the start/cancel button it should start to drain water out. can you hear it drainin into the sink???can you at least hear thje drain pump activated trying to pump???perhaps its humming... if so id check your drain connection under the sink for blockage, and then next remove the drain pump itself and look for debris clogged within it stoppin drain

Mar 22, 2008 | Frigidaire 24 in. PLD2850 Built-in...

2 Answers

Bosch Dishwasher won't drain, cancel drain lights blink


when you said "I can run a wash", does the machine act normal for that time frame up to the point of drain? if yes, the pump is fine. sounds more like the micro chip on the board is "confused", but not sure why.

Jun 04, 2007 | Bosch 24 in. SHX99A15UC Stainless Steel...

Not finding what you are looking for?
Whirlpool 24 in. GU3200XTP Built-in Dishwasher Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4367 Answers

Bruce Denton

Level 2 Expert

273 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...