Question about Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Open Question

Bottom Lid wont close on dishwasher - Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the Bottom Lid to close on dishwasher


Please expand on your question. Which part are you referring to as "bottom lid"?

Jun 22, 2014 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Why is the bottom drawer stuck?


Is this a Fisher Paykel Dishdrawer?
If so, the lid is likely not returning properly to the upmost position.

Caused by faulty lid actuators, easily fixed by replacing them.

Try not to open and close forcefully as it will damage the rubber seal (built into the lid), then you will also have to replace the lid.

May 14, 2014 | Dishwashers

1 Answer

My dishwasher fisher pykel twin dish washer model # DD 605 , SHOWS AN ERROR CODE f7 first then shows error code f9


The top dishdrawer is hard to open or close as the lid seal actuator motors are most likely faulty or lost power. The scraping is the lid seal touching the drawer lid. The F7 and F9 error are a result of this fault with the actuator motors.
At the base of the dishwasher housing under the bottom drawer is the power board. From there the power is supplied to the controller and the motors. These motors move the lid seal into position. First turn the mains power to dishwasher off and then back on. See if this resets the motor position. If not you will have to call the technician to fix the problem. But if you are technical savy you could go to the base of the dishwasher and take the connectors of drawer 1 out from the power board and swap with drawer 2 which is working.
If power board connection is not making any difference, then motors are the likely problem. Needs a lot of expertise to replace and adjust the motors.

Mar 23, 2014 | Fisher and Paykel 23 in. DD-603 Built-in...

1 Answer

F1 and beeping


F1 means the drawer lid is not closing properly - (lid seal leaking) which caused water to splash out when you started the wash cycle. The flood circuit on base of dishwasher housing (under the bottom drawer) has tripped. You will have to find the source of leakage and also dry the base of dishwasher housing. Make sure the dishwasher is unplugged form mains socket when you work in it.

Jan 16, 2014 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Drawer wont shut


If it is one of the two drawers that will not shut, them most likely the lid seal is locked in close position or the lid seal is damaged and pieces of it are blocking the drawer.
Try to shut the power to the dishwasher and take the power chord out from the socket. Then insert back and turn power on.
See if this makes a difference. If not the lid actuator motor or the lid seal need to be replaced. Will need a technician if you are not familiar with repairs especially the dishwashers are very sophisticated and are sensitive to how one repairs it.

Jan 05, 2013 | Fisher and Paykel 24 in. DD-602 Built-in...

1 Answer

Dd603w wont close the last 1/4"


Greetings,
There are a few things that could keep it open..check to see if your lid is closing.. there are hoses and such that can cause this..Try and unplug it or turn off breaker and let sit 5 minutes..see if it works...Again, there could be problems with the lid closers..

Jan 27, 2011 | Fisher and Paykel 24 in. DD603H W Built-in...

2 Answers

Top dishwasher drawer will not close


As long as there is no plates or anything stopping it from closeing i will then say that there are 2 side rails that the draw glides in & out on,get down on the floor & check up underneath the draw for smooth gliding operation.also is it possible that a fork or peice of cutlery has gotten over the top & fallen down jambing the draw from closing.

May 29, 2010 | Fisher DD603B / DD603W / DD603H Dishwasher

1 Answer

Dishwasher lid stuck


the lids on dishdrawers are pulled down and sealed by lid activaters. there r two types, the screw type and the magnetic solonoid type. the reason your draw gets stuck is your lid activator is not releasing. there are 2 reasons for this 1st- 1 or both activators are faulty. 2nd the lid activator control board is faulty, which is located under the bottom drawer.pull the draw out and see if u can see if the lid is down on 1 side or both sides.please reply 4 more help.

May 02, 2010 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Bottom drawer of dishwasher is jammed and stiff..cannot close...as well soap dispenser is stiff...what to do


The lid is pulling down by either left or right actuator causing the lid seal touching your tube. In running mode these 2 actuators pulling down the lid to seal the tube so no water leaking. When the cycle is completed, the actuators push the lid up. In this case one of them is bad not pushing the lid up. The actuators are not hard to replace. When you order, it comes with a pair, replace both. Inspect the lid, if the seal is damaged, you can order the lid to replace together.

Oct 24, 2009 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

How do I test the lid motor on the bottom unit. The lid is not closing properly and triggers F1. I dried sensor and the upper unit is working.


set for rince cycle start it and then pull gently if working properly the drawer wont move any slack change the lid motors

Jul 12, 2009 | Fisher DD603FCSS Dishwasher

Not finding what you are looking for?
Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Dishwashers Experts

Mark Davis

Level 1 Expert

18 Answers

Bruce Denton

Level 2 Expert

273 Answers

Paul Bade

Level 3 Expert

1662 Answers

Are you a Fisher and Paykel Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...