Question about UPM 120V/240V Heavy Duty Outdoor Programmable Timer

Open Question

Where can I get parts for a GE 15164 timer switch

I need the timer wheel & program fingers W/ screws

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have an indoor light switch timer and it is going on and off all the time. How do I reset it so that there is no program on it? or just reset the program?


Timer is not identified. You posted under Sylvania timer:
Open following link for instruction manual for re-programming timer.
http://waterheatertimer.org/Sylvania-timers-and-manuals.html

Problem is not clear.
Do you want to permanently override timer?
Most in-wall timers have override button, but the timing programming resumes at next set point.
When you re-program timer, it lets you set on and off times, but does not let you convert the timer to an ordinary on-off switch.

There is 1 type of timer that has timing function, PLUS optional ordinary on-off capability: Intermatic KM series, Tork 701, Woods 59017, GE15070
http://waterheatertimer.org/Programmable.html#15070

To replace the timer with ordinary on-off switch:
Buy on-off switch at hardware store. Switch will have 2 brass-colored screws and 1 green-colored screw.
Turn off power.
Remove timer wires, but note 1) which wire connected to timer red-or-blue wire and 2) which wire connected to timer black wire.
These two wires will connect to different brass colored screw on new switch.

Jun 30, 2011 | Sylvania Hardware & Accessories

1 Answer

I have a HB31R timer and asm having difficulty setting the timer. Please help.


Make sure the on and off indicators are approximately an hour away from the current time you wish to set the timer to. Using your thumb and one of your fingers (ring, index or middle) grasp the edge of the yellow time indicator. Pull the time indicator straight out away from the back of the unit. While the time indicator is pulled out rotate the wheel to the correct time in reference to the time pointer. Release the time indicator and set the on and off indicators to the desired times in reference to the time printed on the time indicator. Manually move the bottom switch to on or off state which the timer should be at the current time. If you do not see the time wheel move after approximately 30 minutes the timer could be defective.

Mar 03, 2011 | Intermatic & Indoor/Outdoor Rain Tight...

1 Answer

I need instruction manual for TD126 timer


TD126 timer

I'm going to guess at these instructions since they're not posted anywhere yet.
It's a chance I will be wrong, and others can add a comment and refine the answer.

The other option is: you can buy timer and scan your manual into pdf format and post it on your website for free.
Then add a comment with manual web location so we fixyans can sell your manual and manual information to other folks who are wanting a manual to sell to other folks.
Another option: You can pay a fixyan to buy the timer and do the work for you.

My guess is that free is better:

Plug timer into outlet for 1 hour to charge battery.
Remove timer from outlet to program.
Timer appears to be a 24-hour repeat timer with 12 hour am-pm format
There are 5 buttons on face of timer: Reset SET + - Finger
-Press reset button to clear programming.
-Set current time: Push and hold finger button while pressing + and - until current time and am pm display. Or push and hold SET button while pressing + and -.
Program timer:
-Press finger until PROG 1 ON displays
-Press press + and - to set program1 ON Hour.
-Press SET to confirm hour
-Press press + and - to set program1 ON minute.
-Press SET to confirm ON minute

-Press finger until PROG 1 OFF displays
-Press press + and - to set program1 OFF Hour.
-Press SET to confirm hour
-Press press + and - to set program1 OFF minute.
-Press SET to confirm OFF minute

-Press finger until PROG 2 ON displays
-Repeat steps above.
-When programming is finished, push set button.
And you might have to push finger button, or push and hole finger button, and then set button.

-Timer appears to be in AUTO as default mode.
Timer may also have a switch located on side of timer. Move switch to timer if there is a switch.
Some timers also require you push two buttons at same time to enter different modes, or hold one button while pushing other button.

Add a comment for more free help.
Also take advantage of fixya phone service.
For a price, fixya expert speaks with you over phone while you work on timer.

Jan 10, 2011 | Hardware & Accessories

1 Answer

My paragon timing motors model 1015-00RSB are not timing as desired,how can i or guide me on how to programme and make schedule adjustments on it? Please help me


http://waterheatertimer.org/Paragon-timers-and-manuals.html#1015

The Paragon 1015 timer is a 24-hour timer.
The tripper pins or tabs are built into the timer dial.
This timer has NO and NC terminals.
NO NC terminals mean the timer can control two different circuits.
One circuit would be ON when the other circuit is OFF.
When the timer turns on, the circuits change so now one circuit is OFF and the other circuit is ON.

If you have just one circuit, then the following instructions will help you.
If your timer controls two circuits, you can add a comment and I can help further.

OK, your timer controls one circuit.
Locate the tabs on the timer dial.
Push down all the tabs.
Now lift all the tabs for the times you want your Load to turn ON
So if you want the Load to turn ON from 7pm to 5am, then lift all the tabs between those times.
Now when the timer dial rotates, the tripper tabs operate an on-off lever that turns the Load ON and OFF.

Set current time of day
The timer has to be set to current time.
For example it's 6pm.
Grasp and rotate dial until 6pm lines up with the stationary red pointer

Skipper wheel:
The 1015 series has a skipper wheel that lets you skip days of the week.
On these days the timer program will not turn the Load ON or OFF
So if your regular schedule is ON from 7pm to 5am, then the Load will remain OFF for those times.

Set skipper wheel:
Locate day to be skipped on the small dial.
Raise the set screws for the days you want to skip
Raise set screw until it is tight, but do not force

After a power failure, current time of day has to be reset.

If you need more help, add a comment and I will assist.

Nov 03, 2010 | Paragon 1015-00RS Indoor Multi Operation...

1 Answer

I have an Elnita 250 there is a problem with the wheel, when turning it it does not operate the needle up and down?


Make sure the stop motion wheel is tight, if it will not tighten you will need to undo the stop motion wheel, undo the screw that is in the stop motion wheel, unscrew the stop motion wheel all the way off and you will see a three pronged washer, take the washer off and put it in a different position, put the stop motion wheel back on and tighten to finger tight, screw the screw back up in the stop motion wheel, a final turn one the the stop motion wheel to tighten then test, if it does not work put the three pronged washer in a different position even upside dowm.

Apr 09, 2010 | Sewing Machines

1 Answer

Cant locate defrost timer


You have an adaptive ( electronic ) defrost timer . This is located at the top of the refrig section , in the far back right corner . Those 2 , 1/4 " screws , are the mounting screws for it .
On both sides of the upper control panel , are slots , and " d " shaped holes to put your fingers in . Insert a finger on each side , and pull slightly downward and foreward , to remove the panel .
Using a 1/4 " tool , remove the back screw , and the 2 screws holding the temp setting plate .
Use a phillips screwdriver , to remove the 2 screws , located behind the light bulbs .
You should be able to access the adaptive timer now . Pt # 61005988 .

Dec 15, 2009 | Jenn-Air JCD2389G Side by Side...

1 Answer

Need to find parts for a york timmer model 1103


i have lost the screws that go on the timer wheel to start and stop the timer.

Nov 10, 2009 | York / Cam-stat Compressor Cycle Timer...

1 Answer

Defrost timer locationon maytag plus side by side


You probably have an adaptive timer . The timer is located in the far top right corner in the fresh food section ( refrig ) . A "finger hole" on both sides of the control cover are slightly pulled down then foreward to remove the cover . two 1/4" screws hold the temp indicator on ( 1 on each side ) , then 2 phillip head screws about 3" behind them are to be removed . Lastly , one 1/4" screw straight back ( usually painted white ) has to be removed , and the whole panel drops . There are 2 screws holding the adaptive timer on which you will be able to distinguish , to be removed . Installation is in reverse .

Jul 10, 2009 | Freezers

1 Answer

York timer roblem


Grasp the timer dial with your fingers and pull out on it to turn. Set the time of day with arrow at bottom and release. That's it!

If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Jun 15, 2009 | York / Cam-stat Compressor Cycle Timer...

1 Answer

How to program Intermatic model T101-70


Do you have the screw on trip pieces? They look like little arrows with a thumb screw on them. Some of them should say On, some Off Place the on trips over the time you want the lights to com on vice versa for off. To set the time pull out on the yellow time wheel and rotate until the arrow that is pointing down is over the current time. I hope this helps.

Nov 21, 2008 | Intermatic & Indoor/Outdoor Rain Tight...

Not finding what you are looking for?
UPM 120V/240V Heavy Duty Outdoor Programmable Timer Logo

Related Topics:

300 people viewed this question

Ask a Question

Usually answered in minutes!

Top UPM Hardware & Accessories Experts

Brad Brown

Level 3 Expert

18110 Answers

Gene Haynes

Level 3 Expert

5390 Answers

Tom Chichester

Level 3 Expert

54386 Answers

Are you an UPM Hardware and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...