Question about OKI C5650n LED Laser Printer

Open Question

Reset drum on OKI C5650 printer

Thanks for your reply RASHID I tried this but when I get to step 2 OKI USER" does not come up. It says "System mainte 1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time. 2. Menu window will show "OKI USER" 3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button. 4. "Diagnostic Mode xx.xx.xx S-Mode is indicated. 5. Scroll to "NV-Ram initial" is indicated. Push ENTER. 6. Window shows "NV-Ram- Initial Table 1". 7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.

Posted by on

Ad

5 Suggested Answers

Soulvisitor

Soulvisitor

  • 1113 Answers

SOURCE: Have to put printer "online" after every page

Tec says - what sort of blink ??? blinking error light on your printer indicates many things besides jam and there are 5 types of blinks too ( odds are wants toner)

Here is your user manual that explains

http://www.oki.co.uk/binaryData/5929/B4K2uEN1.pdf



Original software includes a status monitor that reports printers errors on your computer screen

Posted on Nov 05, 2007

Ad
Soulvisitor

Soulvisitor

  • 1113 Answers

SOURCE: Communication Error

Disconnect from pc, restart printer on it own, same prob then will need firmware reinstalled, hard drive replaced or even main controller, Job for a tec.

Works ok alone then driver issue delete and reinstall driver check cable too.

Posted on Dec 20, 2007

Ad
Buschchris1

Chris Busch

  • 474 Answers

SOURCE: OKI B4600 Printer will not print = error - paused

Does it have a control panel or buttons on the printer itself?

If so, are any of them blinking or red?

Sometimes an error will cause a pause in the printer and you have to press one of the buttons to get it to start back up again.

http://my.okidata.com/PP-B4600-Black.nsf?opendatabase

This is the link to the manuf. website. I did a search on your model, theres a few so i guessed. but the manuals are available along with drivers.

I suggest you go and update them and go through the PDF and see if there is anything partaining to this issue.

I went through the PDF a bit and didnt see anything partaining to the PAUSE issue but try going through and see if anything is it.

On the printer icon on the bottom right of your task bar, right click on the printer icon and see if you can select CANCEL print job, then try unpausing it. Also, power off and then power back on and see if that clears it.

You may have to un-install the printer and re-install it and update the drivers to clear it.

Sometimes a Print job will get stuck in que when theres a jam or something and it wont continue till the issue is resolved, then you open and close the top cover and that resets it, it rechecks then continues.

Good luck.

http://my.okidata.com/PP-B4600-Black.nsf?opendatabase

Posted on Feb 04, 2009

1vizesember

  • 1 Answer

SOURCE: OKI C5600 error code 411 says toner cartridge is empty (isn't)

Kedves Mindnyájatok!
AZ alábbi hibaüzenet jelenik MEG AZ OKI C5600dn kijelz?jén Minden szín? tonernél. Sot MEG AZ eredeti sárga-NAL van.
Chip cserével lehet orvosolni SEM a problémát. Eddigi javaslat volt: 4 db toner éS alaplap csere. Ennyiért pia con színes nyomtatót is lehetne mar venni. Tudnak segíteni? Van Valami praktikus javaslat a hibám orvoslására?
További Szép estét kívánok!
Lacika

Posted on Nov 05, 2010

Gale Todd

  • 1116 Answers

SOURCE: OKI c5650 flashing "K drum life" I buy new charge

1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

All toner, drum, fuser and transfer figures return to 100%.

In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.

If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Posted on Jun 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset code error c6100


Hi,
Please Follow step by step..
1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.
Read more help..error code 0xc18a0106 on c5180 Photosmart and HP Printer Support

Thanks,

Sep 10, 2014 | Office Equipment & Supplies

1 Answer

RESET DRUM


TRY THIS
1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

All toner, drum, fuser and transfer figures return to 100%

Jul 22, 2014 | OKI C5650n LED Laser Printer

1 Answer

I have oki b710 and only loading... message is displayed but nothing else happeness printer doesn't initialize.


I called this number - 1-800-654-3282 available 24/7
and they have steps
1. Turn off the printer
2. Press the "menu" and "online"
3. Press until the screen says - "Format User Flash"
4. Press "enter"
5. Restart printer when prompted

Apr 11, 2012 | OKI Printing Solutions B710dn Printer

1 Answer

OKI c5650 flashing "K drum life" I buy new charge


1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

All toner, drum, fuser and transfer figures return to 100%.

In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.

If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Jun 08, 2011 | OKI C5650n LED Laser Printer

1 Answer

How to reset oki microline 5520 9 pin


You can reset the printer back to the factory defaults by:

1. Turn the printer off
2. Hole SEL and LF together while you turn the printer on.

If you need any additional help you can obtain the user manual here: http://bulgaria.oki.com/support/printer/user-manuals/index.aspx?prodid=tcm:152-4166

Mar 27, 2011 | Computers & Internet

1 Answer

Fatal error 980


Hello,

1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.


Thanks,
Bhautesh.

Aug 21, 2010 | OKI C5500n Printer

2 Answers

I have a Oki b6500. Replaced the fuser. How to reset the message exchange, "Maintenance." Please help!


The following procedure was provided by Oki Tech support when a web search did not provide an answer. Resetting the Fuser After Replacement - When Counter is NOT Reset First print out a MenuMap and note the fuser count, to later verify that the maintenance reset has taken affect. To reset the fuser counter, enter the diagnostics mode and go to Maintenance Mode Step-1 How to enter the maintenance mode. Hold the Menu & Right arrow button while powering on the printer. Hold the buttons down until the op panel displays “Initializing”. The op panel will display “Output Test” Step-2 Press the down arrow three times. The op panel will display “Maintenance Info” Step-3 Press the right arrow. The op panel will display “Reset Maint Reqd Execute” Step-4 Press the select button. A quick flash will come up on the op panel “Resetting Maintenance Reqd”. The op panel will then display “Reset Maint. Reqd. Execute” Step-5 Press the Cancel button to exit the Maintenance Mode and go back to “Online”. This completes the process, please print out the Menu and inspect the Fuser Count it should read ‘0.’

May 19, 2010 | OKI B6500 Led Printer

2 Answers

Oki C6100 Laser Printer drum reset - from Fatal


1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

Feb 09, 2010 | OKI C6100n Laser Printer

1 Answer

Oki b4600 displays check image drum toner senror error


Try this:

Press Online
Press Menu repeatedly until MAINTE MENU displays. Press Select.
Press Item+ until DRUM CNT RESET displays.
Press Select.

Jul 01, 2009 | OKI B4600n Printer

2 Answers

Fuser reset / transfer reset


RESET OKIDATA TONER DRUM by RTINSC (11/17/05 10:34 AM) reply + / -
1. Turn machine on while pushing and holding the TWO up/down menu buttons at same time.
2. Menu window will show "OKI USER"
3. Scroll to " Engine Dialog Mode" is indicated. Push Enter button.
4. "Diagnostic Mode xx.xx.xx S-Mode is indicated.
5. Scroll to "NV-Ram initial" is indicated. Push ENTER.
6. Window shows "NV-Ram- Initial Table 1".
7. Push ONLINE and ENTER Buttons simultaneously and HOLD for 10 seconds after you see "Executing Reset" appear in menu window.
8. Restart printer.

All toner, drum, fuser and transfer figures return to 100%.

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Aug 11, 2008 | OKI C5510 MFP All-In-One Led Printer

Not finding what you are looking for?
OKI C5650n LED Laser Printer Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top OKI Office Equipment & Supplies Experts

WTF Chuck.....
WTF Chuck.....

Level 3 Expert

387 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Ekse

Level 3 Expert

13434 Answers

Are you an OKI Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...