Question about Stanley GR100 DualMelt Pro Glue Gun Kit

1 Answer

Is there a seal between the nozzle and the tip? I have glue leaking out everywhere??

Glue leaks out around the plastic heat guard once the glue melts.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,406 Answers

No, no seal. The heating element is just a heated tube with the nozzle simply threaded into its end. The heating element in your glue gun may be cracked. Or... possibly... you (or someone in your household) got it hot and laid it down and left it that way for a LONG time, and the melted glue backed up inside the heating element. A glue gun should never be laid on its side while hot but idle, especially for long periods of time.

Posted on Jul 31, 2014

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a leak from the input gasket my kenmore 400 washer, which is plastic and has cracked, can I repair it myself?


yes you can lock tight glue for rubber and plastic.(tube glue not superglue it's like a gel) thin amount of glue locks it in place or a blob of glue turns into a rubber seal. also stops cracking from same crack. used it myself works great.

Jun 02, 2018 | Kenmore Washing Machines

1 Answer

Idea as to cost of this and how it works please


The cost of a glue gun varies between $5-$20 for a good one.
The glue gun works based on heat, in the front of the glue gun there is a heating element, once you install the glue cartridge and press the trigger the glue cartridge is pressed thru the heated element who melts the glue forcing it thru the front nozzle

Mar 18, 2015 | Crafts & Hobbies

1 Answer

Cant remove nozzle tip from nozzle base on aleenes ultimate heated glue gun, even while hot


Here is a great blog on how to change a glue gun nozzle. But big things to remember, preheat the gun, use gloves or a wrench and be careful! If you don't preheat your glue gun, you are likely to strip the nozzle and then be unable to use it again and may even break the gun. Hope this helps!

http://www.gluegun.com/blogs/tips-tutorials/7918501-how-to-change-a-glue-gun-nozzle

Dec 01, 2013 | Crafts & Hobbies

1 Answer

Glue kenmore vacuum plastic


The glue might not work because glue can melt and since it is close to your vacuum motor that creates heat causing it to melt so I personally would just go buy a new one they are like 20$ but if you want to keep on trying glue I think super glue would be your best gues

Apr 16, 2012 | Vacuums

1 Answer

My Adtech glue gun heats and melts stick but nothing comes out the nozzle???


sometimes the trigger can be very hard to pull. if the glue is melting but not coming out the nozzle, where is it going?

Jul 01, 2011 | Crafts & Hobbies

2 Answers

My 2004 kx 250f is leaking oil from where the shift lever and gear box meet, how can this be fixed and why might it be leaking?


hi, is this from around the shaft? if so a seal is fitted to this, it is easily replaced by removing the gearchange lever, und using a small sharp pick to push between the shaft and the seal, with not much effort you can pull the old one out,clean around the shaft and seal area and gently push the new 1 in useing even force all round, TIP IF YOU LAY THE BIKE DOWN ON ITS RIGHT SIDE YOU CAN REPLACE THE SEAL WITHOUT REMOVING THE OIL.

Jan 18, 2011 | 2004 kawasaki KX 250 F

1 Answer

I can see the screw at the frond of the pistol, I think I maybe pushed to hard when the glue wasn't ready. Could that be the cause and how can I fix that?


try to heat the glue up more so it melts. if the glue in the nozzle is clogging the works and not heating up enough to melt, try to remove it with a razor blade

Dec 07, 2010 | Dremel 120001 Glue Gun Kit

1 Answer

A rubber spatula was dropped to the bottom during the wash cycle. It melted a small hole in the bottom of the washer, and now it's leaking. Is there a way to patch the hole?


High-temperature silicon glue will probably work ok. Be sure to clean the hole with alcohol and allow 24 hours for the glue to cure. Epoxy would be a better seal, but it doesn't adhere to plastic very well. Hope this helps!

Sep 22, 2010 | Kenmore Dishwashers

1 Answer

Glue Gun Support


Plug the glue gun into an electrical outlet. Make sure it is placed in a secure place, away from flammable items. As the glue gun heats up, a little bit of glue might drip from the end so you won’t want to leave it on a wood table or on carpet. Insert a glue stick into the back of the glue gun. If the glue gun already has a glue stick in the chamber, keep a second one in reserve nearby. Gather the materials you want to glue together. Hot glue works exceptionally well on thick fabrics, dried flowers, Styrofoam, wood and plastics. Since it leaves a thicker residue, it is not the best choice for thin papers, fabrics and ceramics. Check to see if the glue in the gun has melted by squeezing the trigger slightly and touching the tip to a test piece of paper. If the glue comes out easily, the glue gun has heated up fully. If the trigger is hard to pull, wait a minute more for the gun to heat more completely. Pick up the glue gun and squeeze the trigger slightly while you draw a thin line on one side of the item to be glued. Immediately place the other object to be glued on the glue line, pressing firmly. Hold the two pieces together for about 15 seconds. Test to see if the item still holds when you remove one hand. Let the item set for a few minutes in order to “cure.” Once the glue has dried fully, use a fingernail to scrape away any of the excess glue.

Aug 27, 2008 | Dremel 1550:30 Versatip Tool Kit

Not finding what you are looking for?
Stanley GR100 DualMelt Pro Glue Gun Kit Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1420 Answers

JOHN LAPIER

Level 3 Expert

2595 Answers

Paul Carew

Level 3 Expert

3484 Answers

Are you a Stanley Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...