Question about GE WSXH208A Front Load Washer

Open Question

<!-- from fixya rte -->How to remove seal ge front loading washer - GE WSXH208A Front Load Washer

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Bob Gemmell

Bobby G

  • 212 Answers

SOURCE: Need to remove top cover of GE WPXQ3090T2WW top load washer

There should be 2 screws holding it on at the rear. Looking from the rear these will be at each top corner. Once these are removed push the lid from the front of the machine towards the rear and it will pop off.

Posted on Sep 13, 2007

Ad

Anonymous

  • 116 Answers

SOURCE: How do I remove the selector knob on washer

The main selector control know spins off by turning the selector inner knob counterclockwise. The outer ring will then pull off. The other knobs are held on with friction and should just pull off.

The best way to get behind the front panel is by removing the top panel of the machine. There should be 2 gray/solver tabs at the back of the machine near the top if you remove the 2/4 screws from the top then the whole top panel will slide forward then lift off.

Be sure to unplug the machine first.

Posted on Aug 02, 2008

Anonymous

  • 1 Answer

SOURCE: removing cover assembly on GE top load washer

Is your washer a GE Profile Harmony? Do you want to know how to take the top off or the top of the agitor (pulsator)? The top of the washer has four screws in the back top behind the screen once you unscrew them the front of the washer has two clips one on each side and you have to kinda tap it with your palm to get them to pop.

Posted on Jan 13, 2009

Michael Childers

  • 240 Answers

SOURCE: GE Front load washer - cannot unlock door

manual lock release is located inside front panel. remove lower kick panel and reach up on latch side and feel for plastic tab hanging from lock asm. pull down.

Posted on Apr 27, 2009

Maytag317

Victor

  • 1136 Answers

SOURCE: Front load washer- coin removal

Hi, The coin is probably inside the baffle that tosses the clothes around. I believe this nodel has a screw that holds the baffle in place. I hope this helps you. Please let me know if I can assist you further.

Thanks
Vic

Posted on May 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have to replace door lock #8182634 and need instruction on how to take the old part off


Hello,

This article shows step by step photo instructions on how to replace the door boot seal of a common GE brand front load washing machine.

The washing machine in this example is the GE and the door boot seal
j

  • Phillips head screw driver
  • small socket wrench
  • 7mm socket
  • replacement door boot seal
  • lots and lots of patience

  1. replace-front-load-washing-machine-1.1-120x120.jpg remove dispenser Unplug washing machine and remove dispenser.
  2. replace-front-load-washing-machine-1.2-120x120.jpg Remove lower front cover by removing 3 screws holding it on bottom. Remove lower front cover by removing 3 screws holding it on bottom.
  3. replace-front-load-washing-machine-1.3-120x120.jpg Remove screws connecting top control panel to front of washer. Remove screws connecting top control panel to front of washer.
  4. replace-front-load-washing-machine-1.4-120x120.jpg Completely remove control panel from front panel. Remove 3 screws holding top panel on back of machine and slide cover back approximately 1 inch and lift off.
    Completely remove control panel from front panel.
  5. replace-front-load-washing-machine-1.5-120x120.jpg Use bungie cord to tie back control panel. Use bungie cord to tie back control panel.

  6. replace-front-load-washing-machine-1.6-120x120.jpg 'Pop' off the tension spring being careful not to bend or break it. Feel for the tension spring which tightens the door boot seal onto the front panel.
    'Pop' off the tension spring being careful not to bend or break it.
  7. replace-front-load-washing-machine-1.7-120x120.jpg pull the right-hand side of the seal tight to reveal the inner tension ring holding the seal onto the inner part of the washer. With tension spring removed, pull door boot seal away from front panel.
    On GE models, pull the right-hand side of the seal tight to reveal the inner tension ring holding the seal onto the inner part of the washer.
  8. replace-front-load-washing-machine-1.8-120x120.jpg remove inner tension ring IMPORTANT: Use a short stem philips head (such as a Husky No. 2 x 1-1/2 In. Phillips Screwdriver) to loosen the inner tension ring via its clamp screw.
    NOTE: you may have to remove the front panel to gain access to the tension ring. If that is the case, remove the front panel by removing the screws positioned at each corner (four screws total). On some models you may have to first remove a lower-front panel to gain access to the bottom two screws of the main front panel.

Dec 04, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

How do i replace the door boot seal?


Hello,

This article shows step by step photo instructions on how to replace the door boot seal of a common GE brand front load washing machine.

The washing machine in this example is the GE and the door boot seal
j

  • Phillips head screw driver
  • small socket wrench
  • 7mm socket
  • replacement door boot seal
  • lots and lots of patience

  1. replace-front-load-washing-machine-1.1-120x120.jpg remove dispenser Unplug washing machine and remove dispenser.
  2. replace-front-load-washing-machine-1.2-120x120.jpg Remove lower front cover by removing 3 screws holding it on bottom. Remove lower front cover by removing 3 screws holding it on bottom.
  3. replace-front-load-washing-machine-1.3-120x120.jpg Remove screws connecting top control panel to front of washer. Remove screws connecting top control panel to front of washer.
  4. replace-front-load-washing-machine-1.4-120x120.jpg Completely remove control panel from front panel. Remove 3 screws holding top panel on back of machine and slide cover back approximately 1 inch and lift off.
    Completely remove control panel from front panel.
  5. replace-front-load-washing-machine-1.5-120x120.jpg Use bungie cord to tie back control panel. Use bungie cord to tie back control panel.

  6. replace-front-load-washing-machine-1.6-120x120.jpg 'Pop' off the tension spring being careful not to bend or break it. Feel for the tension spring which tightens the door boot seal onto the front panel.
    'Pop' off the tension spring being careful not to bend or break it.
  7. replace-front-load-washing-machine-1.7-120x120.jpg pull the right-hand side of the seal tight to reveal the inner tension ring holding the seal onto the inner part of the washer. With tension spring removed, pull door boot seal away from front panel.
    On GE models, pull the right-hand side of the seal tight to reveal the inner tension ring holding the seal onto the inner part of the washer.
  8. replace-front-load-washing-machine-1.8-120x120.jpg remove inner tension ring IMPORTANT: Use a short stem philips head (such as a Husky No. 2 x 1-1/2 In. Phillips Screwdriver) to loosen the inner tension ring via its clamp screw.
    NOTE: you may have to remove the front panel to gain access to the tension ring. If that is the case, remove the front panel by removing the screws positioned at each corner (four screws total). On some models you may have to first remove a lower-front panel to gain access to the bottom two screws of the main front panel.

Dec 04, 2010 | General Electric WCVH6800J Front Load...

1 Answer

Door on ge front loader washer leaks, door gasket is fine. Could it be the lock not working properly


Yes it could be the door lock not pulling the door in enough to make the seal. Solution... Remove covers and with door pressed in hard, ( You may need help ), adjust the lock mechanism to make seal. Put lock-tite on the threads after it works for you. This will prevent the shaking of the washer from losening of the nuts again.

Aug 01, 2010 | GE WSXH208A Front Load Washer

1 Answer

Water is leaking needs a new seal?


The GE front load washer Front seal does have a common problem withe the front seal getting riped. Open the door and inspect the bottom half, you might find the hole. if not you will half to remove the bottom access area and locate the leak.

Jan 08, 2010 | GE WSXH208A Front Load Washer

1 Answer

Removal of rubber seal


I take off the top cover unplug machine 1st ..Safety...Then take offretaining ring on inner drum /also ring on outer drum remove boot seal..Check utube video, explains in good detail...

Oct 07, 2009 | GE WBVH6240F Front Load Washer

2 Answers

My GE Adora is making my clothes stink like mildew.


welcome to front load machines. the seal is so good that you don't get air circulation after the cycle (like the top loaders). Solution: take your clothes out right away, wipe that water out from around the seal and most important leave the door open when not in use

Aug 16, 2009 | GE WSXH208A Front Load Washer

2 Answers

GE washer not draining


You should have one. Get down low, and look at the kickplate. You should see screws just below the main front panel of the machine.
best regards, --W/D--

Jul 25, 2009 | GE Washing Machines

1 Answer

The washer smells


I Talked with a retail appliance sale's person about two weeks ago because I had the same problem. Buy a can of country time lemonaide and put three scoops into the drum and run it through a regular wash cycle. This removes the odor. Also around the rubber door seal you can pull the rubber back from the drum side and wipe around the seal with lemon juice due to water and detergent being trapped in the seal. Once every month should do the job. It works for me.

Nov 01, 2007 | GE Energy Star WCVH6260F Front Load Washer

Not finding what you are looking for?
GE WSXH208A Front Load Washer Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

geapptech

Level 2 Expert

157 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...