Question about Stanley Measuring Tools & Sensors

Open Question

Find instructions for using Stanley Intelliblock 0-77-011

Just need instructions for using tool to locate studs,etc.

Posted by on

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

wire12me

  • 187 Answers

SOURCE: have a stanley tre550 and need to know how to use

The staples are NOT loaded on top of the pull out shaft; they are inserted directly into the slot that opens when you pull the shaft out. If the nose of the tool is not placed firmly against a surface, it will not fire. Go to Stanley’s website’s knowledge base and type in the model number, and you can get a PDF of directions. http://www.stanleytools.com/default.asp?TYPE=STATICLEFT&PAGE=Support.htm&LEFT=left_support.htm Below is the graphic from their pdf. Here is a step by step: Unplug the tool. Squeeze the end of the shaft at the rear bottom of the tool and pull out the shaft. Flip the tool over on it’s back. Insert the staples, (points up) and then slide the shaft back in. Plug it in, press the on button (under the the power cord in the back). Press the nose squarely against the material and press the trigger.c901269.jpg

Posted on Oct 15, 2009

Ad

Anonymous

  • 1 Answer

SOURCE: need stanley tools photoelectric timer instructions 58455

http://www.thencc.com/stanley/LS/Instruction/58455_TimerManual.pdf

Posted on Dec 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stanley stud finder AC sensor continually beeps on 10mm plasterboard wall


Most stud finders have a sensitivity adjustment that should be carefully adjusted per instruction manual before use.
Failure to do this results in erroneous indications.

If you have adjusted exactly per the instructions with the same result the unit is probably faulty.

Sep 22, 2017 | Stanley Measuring Tools & Sensors

1 Answer

Stanley instructions


Try using a magnet instead. Move the magnet back and forth against the wall, slowly... until it sticks to one of the ferrous screws hidden in the sheetrock. These hidden screws are holding the wall board/sheetrock onto a stud.
Magnets! Free stud finder! and no batteries to replace!

Aug 26, 2014 | Stanley 77 500 Intellilaser Pro Stud...

1 Answer

Instructions


Here's is a link to the manual for download - direct from Stanley.
Good luck!

May 22, 2013 | Stanley 77 500 Intellilaser Pro Stud...

1 Answer

Instruction for Stanley FatMax Stud Sensor Finder 400 (77-730)


Please people dont waste your money but a cheap standard one Stanley 77-730 stud finder is bad does not work at all , miss my old cheapy never failed me

Mar 05, 2012 | Stanley Measuring Tools & Sensors

1 Answer

Not sure how it works - looking for instructions


Hold the stud sensor against the wall where the wall sounds hollow (no stud at this location). Hold the button down while you slide the unit horizontally. When it moves over a stud, it will give you a solid beep and the display will show you a solid vertical line. If it starts beeping intermittently, you may have started over a stud which will cause an error.
Do not lift the sensor off the wall when you slide it as this will also cause an error.

Jan 19, 2011 | Stanley 77-720 Stud Sensor 200

1 Answer

Please advise me to how to use and how it work as there are no instructions in english in leaflets enclosed in pack


Hold the unit flat on the wall. Press and hold the side button (you will hear one short beep). Holding it to the wall, slide the sensor left or right, when you get near a wall stud, the lights will begin lighting up, when centered on the stud, the top light will be lit and it will beep continuously.

Oct 17, 2010 | Stanley Intellisensor 77110

1 Answer

Need manual


The manual is available from the Stanley Tools web site. http://www.stanleytools.com/default.asp?TYPE=STATICLEFT&PAGE=knowledgebase.htm&LEFT=left_knowledgebase.htm . Click on the Search the Knowledge Base button and put in 77260 in the search box in the pop up window. Then click on the link for the line for 77-260 IntelliLaser Pro Instructions. Then click on the icon for the format (PDF) of the manual at the end of the listing.

I hope this helps.

Cindy Wells

Oct 12, 2010 | Stanley 77260 IntelliLaser Pro Combination...

1 Answer

Need instruction manuals


you can find manuals for power tools such as the stud sensor at http://powertool.manualsonline.com/

Dec 31, 2009 | Stanley 77 500 Intellilaser Pro Stud...

1 Answer

Dont know how to use


Hello,

Here are instructions to get the manual for this sensor:

Go to:
Stanley Support

Click on the "Knowledge Base" link.

When the window opens type 77 115 in the search block and click on "Search". (NOTE: Leave a space between 77 and 115 or this will not work.)

The Instruction manual should be on top of the list that appears.

Click on the link under the "Article Name". (77-115 Intellisensor Plus Instructions)

On the next window click on the small icon under "Format". That will open up a PDF file for you. Save it to your computer for future use.

If you have any trouble, just comment back.

Thanks for using Fixya.

Mar 24, 2009 | Stanley 77 115 Intellisensor Plus Stud...

Not finding what you are looking for?
Measuring Tools & Sensors Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Measuring Tools & Sensors Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Lawrence Oravetz

Level 3 Expert

10543 Answers

Frank Walton

Level 1 Expert

26 Answers

Are you a Stanley Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...