Question about Behringer Music

1 Answer

I won't behringer mx3282a power supply circuit diagram

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Behringer Master
  • 3,156 Answers
Ad

4 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Fred Yearian

  • 5603 Answers

SOURCE: Behringer Xenyx 1622FX. Power supply has failed,

Suspect a broken circuit trace or broken solder. If they use a 7805 three terminal regulator, check the solder around those pins...
Berhinger does NOT release schematics except to their service facilities... I know... I have tried... I repaair a lot of their stuff and have to trace out the circuits.

Power supply circuits are rather easy except for the switching regulators if they have failed totally.

If only the +5 is dead, you should be only a filter cap and a diode or two away from the problem... Transformer leads and electrolytic leads with their weight are favorite to pull out of solder... On Behringer, often the traces are narrow and can have a crack in them.

Posted on Jan 13, 2010

Fred Yearian

  • 5603 Answers

SOURCE: I am looking for a power connector wiring diagram

Some of the mixers have common connectors.

It appears that for the three pin connector, pin 2 is center tap of AC source, and pins 1 and 3 are the ends of the transformer windings.

This is from a schematic of a MX2643A which MAY be similar to yours. One of mine has a 3 pin Amphenol connector with a locking screw ring...

Use this info at your own risk, however, the power inout is easy to trace out to verify. They use a typical bridge rectifier to get plus and minus from the external transformer.

The pin markings on the connector CAN be confusing.

Suggest you use the light bulb trick of putting a small lamp in series with the 120 line as an auto reseting fuse.

Posted on Mar 10, 2010

Fred Yearian

  • 5603 Answers

SOURCE: im looking for a curcuit diagram for the

If the supply failed I can tell you which parts to replace... and if it failed there may be a failure in the power amp that caused it. You can contact be directely at fredy2 @ aol.com... put Behringer in the subject.

The supply when it fails takes out eleven components including two expensive IGBT transistors. If the rearmost amp fried, add at least four more components and a lot of work carving out burned board and wiring around the blown circuit traces.

Posted on May 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for circuit diagram of behringer power amp


Here is a google link. I don't know which one you need.

https://www.google.com/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=circuit%20diagram%20of%20behringer%20power%20amp

Apr 23, 2016 | Behringer Pmp3000 16 Channel Audio Mixer

1 Answer

MX3282A. Where can I get a power supply?


Hi Bryant...
That particular power supply is hard to come across. There is a brand new one for your mixer on E-bay for $200.00 here:
http://www.ebay.com/itm/Behringer-Eurodesk-150-Watt-Power-Supply-For-Mixers-MX2442A-MX3282A-NEW-/252274097139
Hope this has helped you.

Jan 27, 2016 | Music

2 Answers

Behringer pmp1280s circuits diagram


sir,send me behringer pmp1280s circuits diagram .
send me my facebook star32_s@yahoo.com pls....

Aug 05, 2013 | Music

1 Answer

Behringer sx3242fx not working .i need circuit diagram .


Behringer will not release schematics unless you are an authorized service agent... however, sometimes you can make do with the few schematics floating around... What is the problem with the unit? They typically use a switching power supply and the schematics of those aree usually similar enough to repair them.

Sep 09, 2011 | Behringer Sx3242fx Eurodesk 32-channel...

1 Answer

Behringer DDm4000 purchased in 2009. Over 2 years happy usage, but now it's got some major issues! The power supply seems corrupted as after about 2 hours use it maxes out the signal (ouch) and all...


Behringer is stingy about schematics... however here is one for their DJX700 which MAY have a similar power supply to yours:

http://elektrotanya.com/behringer_djx700-professional_sch.pdf/download.html

Scroll down to "get manual" and click to download... IGNORE other download links.
On page 9 near the lower right corner is the simple power supply, minus the transformer but showing the rectifier diodes, filter caps, and the three terminal regulators. These regulators have a thermal shutdown feature so if they seem to run VERY hot they might cause your problem. Common things are failing electrolytic filter caps. Behringer also uses switching power supplies in some gear and I have schematics of examples of those as well... but peak in your unit and see what type supply you have.

Jul 28, 2011 | Behringer Ddm4000 5-channel Digital Midi...

1 Answer

Im looking for a curcuit diagram for the switchmode power supply in my Behringer PMP3000.


If the supply failed I can tell you which parts to replace... and if it failed there may be a failure in the power amp that caused it. You can contact be directely at fredy2 @ aol.com... put Behringer in the subject.

The supply when it fails takes out eleven components including two expensive IGBT transistors. If the rearmost amp fried, add at least four more components and a lot of work carving out burned board and wiring around the blown circuit traces.

May 30, 2010 | Behringer Pmp3000 16 Channel Audio Mixer

1 Answer

Behringer mixer power goes off after running about 5 0r 10 minutes then power turns on.what is problem with the power supply board


That time lag would indicate a thermal problem.

Likely the power supply is a switching type that has some three terminal regulators after it such as 7805, 7815, 7915.

These have thermal protection in them and one may be shutting down.

Use circuit cooler to isolate the part that is shutting down.

May 20, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

2 Answers

Xenyx 1002fx Mixer 10 Input 2 Bus with Efx: behringer mixer power goes off after running about...


Problem is likely thermal. Open unit carefully and use freeze mist (circuit cooler) to find bad component.

With that long a time period, it is possibly a component mounted on a heatsink.

May 18, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

1 Answer

I am looking for a power connector wiring diagram for the Behringer Eurodesk MX3282A? It was rewired by someone and I think the wire combination is mixed up because when plugged in it seems to blow...


Some of the mixers have common connectors.

It appears that for the three pin connector, pin 2 is center tap of AC source, and pins 1 and 3 are the ends of the transformer windings.

This is from a schematic of a MX2643A which MAY be similar to yours. One of mine has a 3 pin Amphenol connector with a locking screw ring...

Use this info at your own risk, however, the power inout is easy to trace out to verify. They use a typical bridge rectifier to get plus and minus from the external transformer.

The pin markings on the connector CAN be confusing.

Suggest you use the light bulb trick of putting a small lamp in series with the 120 line as an auto reseting fuse.

Mar 03, 2010 | Behringer Music

1 Answer

Behringer Xenyx 1622FX. Power supply has failed, no +5V rail, other rails are OK, appers to be no input to the regulator. Could do with a circuit diagram. I believe the PSU is used in other mixers.


Suspect a broken circuit trace or broken solder. If they use a 7805 three terminal regulator, check the solder around those pins...
Berhinger does NOT release schematics except to their service facilities... I know... I have tried... I repaair a lot of their stuff and have to trace out the circuits.

Power supply circuits are rather easy except for the switching regulators if they have failed totally.

If only the +5 is dead, you should be only a filter cap and a diode or two away from the problem... Transformer leads and electrolytic leads with their weight are favorite to pull out of solder... On Behringer, often the traces are narrow and can have a crack in them.

Jan 13, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

Not finding what you are looking for?
Music Logo

Related Topics:

413 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Music Experts

Michial Gueffroy

Level 3 Expert

1140 Answers

Chickenwatt

Level 1 Expert

18 Answers

Ric Weide
Ric Weide

Level 1 Expert

10 Answers

Are you a Behringer Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...