Question about Goodman Manufacturing Goodman GMS81005CN 100,000 BTU 80% Gas Furnace, 1 Stage, Multi-Speed,

1 Answer

My goodman furance runs on full cycle then it won't start again til i turn power off then back on

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 572 Answers

May be a stuck relay on the circuit board. The only other thing I can think of would be a thermostat having intermittent problems.

Posted on Feb 28, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a gmp125-4 furance blower runs all the time checked themostat wires error code 1 blink then 2 then 3 then 5 furance works if you turn power off turn back on when heat kickes off blower comes on gives...


Sounds like limit switch issue. Furnace heats up, high temp limit switch opens, fan will stay on. GMP model is older and do not have the codes.
May be over fired, have airflow problem, to cause the limit to open.
Next time before shutting off power, try to find the limit, it has two wires that connect to a 1.5 x 2 inch card mount to the furnace fire wall. tap on it and see if the blower stops. If so replace the limit.

Sep 06, 2011 | Goodman Heating & Cooling

1 Answer

HEATER TURNS ON AND RUNS THEN GOES OFF BECAUSE OF THE ROLL OUT LIMIT. tHE BURNER IS IS FLAMING OUT OFF THE BOX.


The furance needs to be clecned. Is the furance in the sdame roomas a clothes dryer. Lent can plug up the furances burrner tubes. With a shop vac switched to the blower side blow out the tubes and cleran the unit. Be careful not to touch the hot surface igitor while cleaning. These will crack easily.

Feb 13, 2011 | Goodman GMS90703BXA Heater

2 Answers

My girlfriend has a forced air Goodman furnace in her house. Her furnace has been not running well. Whenever the filter gets dirty the furnace does not run right which it to be expected. The problem is...


where is the thermostat located? i should be on a inside wall in a comon room and not around lights, computer or heat vent or air return. a thermostat is just a switch and will operate in its enviroment. does the fan cycle off before the heat starts blowing again? the fan on these are on a timer that the t stat will have to "brake" open on reaching temp to shut off. not knowing where your at look this over and i hope it helps. i dont think i would let someone sell me a control board for this problem.

Feb 08, 2011 | Goodman GMS90703BXA Heater

1 Answer

Unless we set the thermostat very high, like 80 degrees, the heater will blow cold air. When the heat does blow, it will eventually stop blowing heat and the fan will continue to blow cold air.


Check and make sure the filter is clean. This sounds like a restriction in the system. If the unit has central cooling make sure ther indoor evaporator coil is clean at the furance.The unit may be cycling the burners on and off at the high heat limit , fan/limit control. You can also eliminate the thermostst from the furance. Turn power off at the furnace and disconnect the wiring from the thermostat. Jumper the red and white wire together. Turn the furnace back on. The furance should run in the heating mode. Try this and see if the problem is still there.

Jan 25, 2011 | Heating & Cooling

1 Answer

Pressure switch is what furance says is the problem. ohmed out switch its good flu is not obstructed have power going to switch


Check the pressure port on the side of the draft inducer for blockage. Goodman refuses to acknowledge the problem.

Oct 18, 2010 | Goodman GMS90703BXA Heater

1 Answer

When i turn on my furance it starts up later it will try again and the system will lockout with one flash on the board indicating retries recycles exceeded any ideals?


check to make sure the gas is on and the flu pipe is clear.  does the draft motor come on at all?  if not, you may have a failed control board.

Nov 29, 2008 | Goodman GDS80703ANA Open Flame Mid-Size...

1 Answer

Furance lights and goes out after ten seconds does this three times.bought a new flame sensor worked two days same thing again.goodman furnace


If it isnt the flame sensor make sure the furnace ground wire is hooked up.If the ground is bad it cant sense flame.

Oct 20, 2008 | Goodman Heating & Cooling

2 Answers

Furance won't lite


The first thing i would do is turn thermostat down and turn power off wait for a few minutes then turn power back on and then thermostat back up. If it has a ignition module then there should be a blower motor. It should come on then a pressure switch that should click then the ignitor should glow or spark. there should be a round glass circle that you can look through to see the ignitor

Apr 04, 2008 | Goodman GMS90703BXA Heater

Not finding what you are looking for?
Goodman Manufacturing Goodman GMS81005CN 100,000 BTU 80% Gas Furnace, 1 Stage, Multi-Speed, Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Goodman Manufacturing Heating & Cooling Experts

bobalix

Level 3 Expert

471 Answers

snowmanii

Level 2 Expert

477 Answers

ray gallant
ray gallant

Level 3 Expert

65406 Answers

Are you a Goodman Manufacturing Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...