Question about Oreck XL21 Bagged Upright Vacuum

1 Answer

Motor smells Oreck Xl2 - Oreck XL21 Bagged Upright Vacuum

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oreck Master
  • 932 Answers

If it smells electrical, than you may need a new motor. If it smells more like burnt rubber, than you may have a brush or motor problem. To check you brush, take out the 5 screws that hold your bottom plate on the vacuum and remove the plate. Disengage the belt and see if the bearings at each end of the brush turn freely. If they do not, replace your brush. Also spin the motor shaft by hand and see if it turns freely. Hope this helps!

Posted on May 12, 2015

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 310 Answers

SOURCE: wiring diagram Oreck XL2

http://geeksquad.fixya.com/ThreadView.aspx?prdid=19810&thid=650346
Wiring diagram Oreck XL2
Posted by geohil on Jun 06, 2008
Can I get a wiring diagram of the handle on an Oreck XL 2.

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Oreck XL Ultra Bagged Upright Vacuum. The best place to get an owner’s manual is from the Oreck Factory of which I will supply for you listed below or you can download the owner’s manual from the Oreck Website. . I would check with your local Oreck dealer or vacuum dealer in your area to see what is going on. This is most unusual for this to happen. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.oreck.com/ Customer Service 1-800-989-3535
Monday thru Friday Hours are: 7:00 am to 7:00 pm CST
Saturday and Sunday Hours Are; 8:00 am to 4:30 pm CST
http://www.a-1vacuum.com/ 1-800-657-1874 Customer Service
Thanks, Don the Vac Man
Go Ahead. Use Us.

Posted on Jun 09, 2008

Anonymous

  • 5 Answers

SOURCE: lost instruction book

remove screw on side of unit, slide cover and replace belt with spare on the bottom.

Posted on Oct 15, 2008

Anonymous

  • 67 Answers

SOURCE: I shut my vacume off to change its bag out. Now it

An access panel mounted atop a vacuum nozzle base via finger operated latches. When the latches are undone the access panel is removed from the top surface of the nozzle base allowing access to the parts of the brush assembly. The panel also has an integral arm which engages a safety motor switch such that when the panel is removed the motor switch is switched into an open circuit position preventing the motor from continued operation

Posted on Sep 23, 2009

Vac Belts

Vac Belts

  • 701 Answers

SOURCE: My oreck XL7 smells when it's on. Smells as if

The smell is probably from the belt. When they are worn and stretched they can start to smell. You can get replacement belts for your model here:

Oreck XL7 Replacement Belts

Posted on Nov 11, 2009

cj4opal

  • 1 Answer

SOURCE: Simply won't turn on!

my oreck xl21-700 ect vaccum, the brush won't spin and i have a new belt

Posted on Aug 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to tell if switch bad..xl2 stopped working


If you have power in the outlet and the vacuum does not come on 9 times out of 10 it is the switch especially in the oreck or if the switch feels like there is no snap or click when turning on and off

Nov 20, 2010 | Oreck XL2600 Vacuum

1 Answer

Oreck XL2 does not start.


There could be a problem with the cord. I suggest taking it to a local vacuum shop to have it inspected as that could be the problem

Apr 13, 2010 | Oreck XL2000 Bagged Upright Vacuum

2 Answers

Simply won't turn on!


I believe all Oreck vacuums have a lifetime warranty. You should pursue that.

Mar 11, 2010 | Oreck XL2200 Bagged Upright Vacuum

1 Answer

I have a oreck xl2 and while vacuuming the vacuum quit. The vacuum has the red power light on. Please advise


sounds like a bad motor. if the light is on at the switch and the motor doesn't run, then it could definitely a motor problem, worn down or dirty carbon brushes. the motor on these machines are not the best built, they require cleaning of the commutator yearly.

Nov 18, 2009 | Oreck XL2200 Bagged Upright Vacuum

1 Answer

My oreck XL7 smells when it's on. Smells as if it's the motor. Had the Oreck for 4 years but hardly used it?


The smell is probably from the belt. When they are worn and stretched they can start to smell. You can get replacement belts for your model here:

Oreck XL7 Replacement Belts

Nov 10, 2009 | Oreck XL Ultra Bagged Upright Vacuum

1 Answer

I shut my vacume off to change its bag out. Now it won't come on. Oreck xl2. There were no noises before turning it off or any smells of rubber burning. Just won't come back on. Is there a reset button....


An access panel mounted atop a vacuum nozzle base via finger operated latches. When the latches are undone the access panel is removed from the top surface of the nozzle base allowing access to the parts of the brush assembly. The panel also has an integral arm which engages a safety motor switch such that when the panel is removed the motor switch is switched into an open circuit position preventing the motor from continued operation

Sep 23, 2009 | Oreck XL Ultra Bagged Upright Vacuum

2 Answers

Wiring diagram Oreck XL2


http://geeksquad.fixya.com/ThreadView.aspx?prdid=19810&thid=650346
Wiring diagram Oreck XL2
Posted by geohil on Jun 06, 2008
Can I get a wiring diagram of the handle on an Oreck XL 2.

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Oreck XL Ultra Bagged Upright Vacuum. The best place to get an owner’s manual is from the Oreck Factory of which I will supply for you listed below or you can download the owner’s manual from the Oreck Website. . I would check with your local Oreck dealer or vacuum dealer in your area to see what is going on. This is most unusual for this to happen. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.oreck.com/ Customer Service 1-800-989-3535
Monday thru Friday Hours are: 7:00 am to 7:00 pm CST
Saturday and Sunday Hours Are; 8:00 am to 4:30 pm CST
http://www.a-1vacuum.com/ 1-800-657-1874 Customer Service
Thanks, Don the Vac Man
Go Ahead. Use Us.

Jun 06, 2008 | Oreck XL Ultra Bagged Upright Vacuum

3 Answers

Wiring


Here are the 4 different wiring for new Oreck motors.
2e7c587.jpg

Apr 04, 2008 | Oreck XL Ultra Bagged Upright Vacuum

Not finding what you are looking for?
Oreck XL21 Bagged Upright Vacuum Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oreck Vacuums Experts

Cindy Wells

Level 3 Expert

6069 Answers

john h

Level 3 Expert

22486 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Are you an Oreck Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...