Question about Bosch Dishwashers

1 Answer

Dish washer not advancing to the next cycle - Bosch Dishwashers

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Bosch Master
  • 713 Answers

This is usually caused by the heating circuit not heating the water. And most of the time, this is NOT caused by a bad heating element, but instead, by a bad controller. A solder connection to the heater relay has gone bad. You can see this easy enough if you take the control module apart. (Depending on the model, the controller is located EITHER in the door, or else on the bottom right-side of the DW.) It is possible to re-solder this connection and get your dishwasher working again, but this is only a temporary solution because the problem is actually in the relay - the contacts have gotten pitted, causing resistance which causes heat which travels down the leg of the relay, causing the solder to melt. The correct solution is to either replace that relay or the complete control module.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Posted on Mar 23, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My washer will not switch from one cycle to the next


I understand that your washer is not advancing and stuck on one cycle. If you provide a Model and serial number, it will be helpful.

Jul 22, 2016 | Washing Machines

1 Answer

I have a Maytag Ensignia washer that will fill with water and start working but will not advance to the next cycle without manually advancing the dial. once helped into the next cycle the washer works...


First you need to list the model number in order for me to figure out what type of washer it is then i can help you. The reason I ask is some Maytag Ensignia's come with electronic timers and some models have old style timers...

Mar 10, 2013 | Washing Machines

1 Answer

Cycle runs too long


long cycle most likely a heater problem.. or thermo problem.. to check heat run a cycle open the door in the middle of the cycle. is a lot of steam coming out... the dishwasher has to get to 70c to advance...if it is hot .then you could have a thermo that is not telling the control to advance the thermo holds the the dishwasher until the temp reaches 70c before it will let it go into the next cycle...the thermo is under the dishwasher at the right side, white with two wires .. it screws into the tub...hope it helps it not let me know and I can help you more.

Sep 27, 2009 | Bosch 24 in. SHX33A02 / SHX33A06...

1 Answer

My dishes still come out wet..how do i set the washer to dry the dishes


there should be a setting or a button to turn the heat dry on and off, if it is on and dishes are not drying then the next time you do a load of dishes pay attention to the cycles, after the rinse cycle is complete the heat should come on. if not you could have either a bad heating coil or a bad relay.

Aug 20, 2009 | Kenmore Dishwashers

1 Answer

Washer stays in cycle and doesnt advance to additional cycle


Hi, It sounds like you timer has gone bad. Would need more of the model # ro be sure on what type timer you have.

Please let me know if I can assist you further.

Vic

Jun 05, 2009 | Kenmore 22622 Top Load Washer

1 Answer

My Kenmore Washer 110.92281100 won't stop


I purchased a new timer, installed and solved the issue.

May 13, 2009 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Washer Doesn't move from cycle to cycle


this washer has a problem with the lid hinge screws coming loose. check the left hand hinge and you will find the screws loose.
this cause the lid switch to not engage and then nothing will happen until it thinks the lid is closed.
try to tighten the screws and listen to see if the switch "clicks" when you open and close the lid.
that should fix it until the screws come loose again.

Jan 30, 2009 | Whirlpool LSR6334LQ Top Load Washer

1 Answer

Washer fills with water but does not advance to next cycle


If this is a rotary timer, nudge the timer slightly in it's normal direction of rotation. If the timer keeps going (it might hang up at the next point in the cycle, but nudge it again), I suspect the timer needs to be replaced. They get weak.

Jan 29, 2009 | Washing Machines

1 Answer

Admiral Washing machine will not advance to the next cycle.


whirpool machine .. it was overload and now it's not draining the water. stops when in the drain cycle./

Jan 01, 2009 | Admiral AW22 Top Load Washer

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

peter gittos
peter gittos

Level 2 Expert

247 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...