Question about Regal Ware K6725 Kitchen Pro Bread Maker

Open Question

Oil coming from shaft contaminating dough why?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cuisinart electric cookie press ccp-10 doesn't press the cookie dough out.


Probably the motor is slipping threads on the drive shaft.

Dec 15, 2017 | Cuisinart Food Mixers

2 Answers

I can't get the dough attachment off my Kitchenaid stand mixer. I have tried oil, filling up the bowl with soapy water and letting it stand overnight, pouring teapot after teapot of boiling water ove


Hi Georgette
You need to encourage movement between the beater and the silver shaft it locks on to. There is nothing that you can unscrew to make it easier. Get a can of CRC and try & get it around the silver shaft at the top of the beater plus you should be able to get a bit in that side slot where the beater engages with that driving pin. Rock (twist) the beater side to side and slowly the grip will loosen and you will be able to encourage it off. Once you have it off you will need to clean out the CRC and polish up that silver shaft. Next is the more difficult part, you need to polish up that hole in the beater. What you are trying to do is remove the build up of flour in the hole so that it is pretty much shiny in there again without being significantly bigger than it was originally. I use a rat tail (round) file to do this job, you are just removing the darker build up in there. When done a good wash and dry and it will be like new again. Keep the hole clean of flour and it may not happen again.

Nov 30, 2014 | KitchenAid KSM150PS Artisan Series Stand...

1 Answer

Drive Shaft stopped kneading dough


To give the mixer strength it has planetary gears. Something may be wrong in the gear section

Nov 26, 2013 | Bosch 800-watt Universal Plus Mixer with...

1 Answer

Where is the ol coming from?


There is a rubber seal in the bottom of your pan that has failed. There is grease under that seal to keep the spindle that turns the paddle lubricated. If your breadmaker is still under warranty contact Cusinart to get help. If it is no longer under warranty then you could still probably order a new pan from them. If you just want to get rid of the darn thing you can always send it to me. At least that way it won't end up in a landfill. You can reach me at daryl441@msn.com

May 30, 2013 | Cuisinart CBK-200 Bread Maker

1 Answer

Dough hook will not come off


I had the same problem too. There should be maybe 1/4" of loose vertical play of the dough hook (or similar attachment) on the agitator shaft. The hook locks in place rotationally on the shaft until it is pushed up. Before you try to turn the dough hook backwards in an attempt to remove it, push it upwards and hold it up, then rotate.

May 22, 2012 | Hobart A200 Stand Mixer

1 Answer

Bread dough beater will not come off


Make sure your Beater can slip in and out of the Beater Shaft
easily. Do not force the beater onto the Shaft if the shaft is bent.
If it cannot be removed easily by hand, use a soft rubber mallet
(not a steel hammer) to slightly tap the beater so it can be moved
up and down the shaft or from side to side. Then you can easily
turn the beater left and remove it from the shaft.

From Kitchenaid Manual:
To Attach Flat Beater, Wire Whip, or Dough Hook
1. Turn speed control to OFF.
2. Unplug stand mixer or disconnect power.
3. Tilt motor head back.
4. Slip beater onto beater shaft and press upward
as far as possible.
5. Turn beater to right, hooking beater over pin on shaft.
6. Plug into a grounded 3 prong outlet.

To Remove Flat Beater, Wire Whip or Dough Hook
1. Turn speed control to OFF.
2. Unplug stand mixer or disconnect power.
3. Tilt motor head back.
4. Press beater upward as far as possible and turn left.
5. Pull beater from beater shaft

Jul 17, 2011 | KitchenAid KSM90 Ultra Power Series Stand...

1 Answer

My toyota after along drive white smoke comes out off the silencer could it be the turbo because the turbo shaft play.


White smoke is caused by water and or antifreeze entering the cylinder, and the engine trying to burn it with the fuel. The white smoke is steam. There are special gaskets (head gaskets are the primary gaskets) that keep the antifreeze from entering the cylinder area. The cylinder is where the fuel and air mixture are being compressed and burned. Any amount of antifreeze that enters this area will produce a white steam that will be present at the tailpipe area.
Check to see if the proper amount of antifreeze is inside the radiator and the overflow bottle. Also check to see if antifreeze has contaminated the engine oil. You can look at the engine oil dipstick, or look at the under side of the engine oil filler cap. If the oil is contaminated with antifreeze, it will have the appearance of a chocolate milkshake. Do not start the engine if the oil is contaminated with antifreeze, as serious internal engine damage can result.

Jul 17, 2011 | Toyota Tercel Cars & Trucks

1 Answer

The dough made by my B2000 Break Maker has black contaminations coming from the paddle shaft. The shaft is quite loose and can be pushed up and down easily. Any help or advice on how to deal with this will...


Hi,
That contamination seems to be oil from the lubricated bearing at the bottom of the bread pan. This bearing is factory sealed, but the seal and the bearing is broken or worn causing the shaft to move freely.

Unfortunately there is no fix and the pan must be replaced.

Hank



Sep 07, 2009 | Black & Decker B2000 Bread Maker

1 Answer

The dough hook is stuck in the beater shaft of kitchenaid mixer


It sounds like it got overloaded when you last mixed dough. It will only come off the way it went on. If it has been bent on, it may need a bit of gentle encouragement.

Jun 15, 2009 | KitchenAid KSM50PR Professional Series...

1 Answer

The paddle will not stay on the shaft while mixing dough.


Probably the paddle and shaft are worn. Both are replaceable. Buy a new Paddle and a Kneader mounting shaft unit (Part No. ADA 29A115)

Panasonic Parts
National Parts Center at 800-332-5368 between the hours of 9:00 a.m. and 8:00 p.m. EST Monday through Friday.

Nov 16, 2008 | Panasonic SD-YD250 Bread Maker

Not finding what you are looking for?
Kitchen Appliances - Others Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Regal Ware Kitchen Appliances - Others Experts

Irene Tulloch

Level 2 Expert

498 Answers

Ekse

Level 3 Expert

13434 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Regal Ware Kitchen Appliances - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...