Question about Ricoh Aficio CL7200 Laser Printer

1 Answer

Error sc551. Replaced the fuser, but still have the error. Need to know how to clear the error code. I have found reset methods for other models online, but they do not apply to the CL7200.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Ricoh Expert
  • 164 Answers

Try this press clear mode button then press 107 then hold stop button for 5 seconds. should go into service mode. select 5 mode then 810 follow instruction and then turn copier off then back on .

Posted on May 08, 2015

Testimonial: "Thanks, but the CL7200 does not have a keypad. I think this applies to other printer models."

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ricoh 1813. Error code c551


The Ricoh copier error code SC551 / 551 is a fusing thermistor 1 error code.

It can mean:
1. The thermistor is not connected
2. The thermistor connector is bad

To reset this error try the code:
"Clear Mode"+107+"Clear/Stop" hold for 5s.
Turn ON and OFF the Main Switch.

If the problem persists you may need to contact a local service technician to take a look at your copier.

Oct 03, 2017 | Ricoh Office Equipment & Supplies

1 Answer

WHAT IS THE CODE SC551?


Symptom]
SC551 (thermistor disconnect: thermistor2) or SC561 (thermistor disconnect: thermistor3) is displayed.

[Cause]
The drawer connector surface is partially corroded.
A foreign object or debris has adhered to the surface of the fusing unit drawer connector contact and, when the adhered moisture melts due to condensation, it causes part of the surface of the drawer connector to corrode. It becomes clear that SC551/SC561 occur because of faulty contact with the image fusing unit.

[Resolution]

Replace the drawer connector on the device.

Apr 25, 2016 | Office Equipment & Supplies

2 Answers

How do i clear error e000007-0000 on a canon ir 2200 photocopier


Fixing film assembly may need to be replaced if error cannot be cleared. Fixing error codes should be reset by a professional only. Fuser assembly must be examined before resetting the E000, E001, E003 and E007 codes. Enter the service mode this way: Press "Additional Function" key, Press "2" and "8" simultaneously, press "Additional Function" key again. Go to COPIER----FUNCTIONS-----CLEAR----ERR. Here your tech can reset the error codes. Then turn machine off & on again.

Sep 04, 2014 | Canon Cannon Ir 2022 Photocopier

1 Answer

Ricoh mp 2550 sc997


Sc551 high temperature error you need to replace both thermistors also check if fuser roller surface worn out then replace that too then just reset your error some cases you just need to clean thermistors and reset error

Nov 06, 2012 | Office Equipment & Supplies

1 Answer

I have a Konica Minolta bizhub D2510F it gives me this error C0501. after searching around I found out that this error is a Fuser error. I replaced the Fuser and the PhotoConductor but I still get the same...


The error has to be manually reset. Here is what I found from the official procedure. Hope it works. How to clear a fuser error code (C0500, C0501, C0510, C0511, C0520, C0521). Solution To clear the fuser error code, perform the following after correcting the cause:
1. With power ON, open the front door and locate the small, rectangular hole below the imaging unit removal tool.
Note: It is not in the same location as the models 7915/7920.
2. Insert a suitable object into the hole to actuate the reset switch .3. The code should clear and a message to close the front door should appear.

Feb 03, 2011 | Konica Minolta bizhub 350 All-In-One Laser...

3 Answers

Printer shows error CH551


Is this actually a Ricoh Aficio 1013F, or another model, because "CH551" is not a ricoh service code?Do you mean "SC551"
If so, this is a fuser "triac" problem (basically a fuse in the heater unit). It can only be reset in service mode after the problem is fixed...and will require a tech.

May 21, 2009 | Ricoh Aficio 1013F Copier

2 Answers

Ricoh 6513, service code 551


SC551 is thermistor pressure roller error. Check for paper jams in the fuser. It could need a new thermistor.

Make sure the fuser is secured and properly seated in the copier.

Jun 12, 2008 | Office Equipment & Supplies

1 Answer

Service code 551


SC551 is an error with the fuser unit. The thermistor could be bad and need to be replaced or the press rollers are worn.

It should be looked at by an experienced technician to get problem repaired.

Jun 12, 2008 | Ricoh 6513 Copier

Not finding what you are looking for?
Ricoh Aficio CL7200 Laser Printer Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ricoh Office Equipment & Supplies Experts

Adorjani Laszlo

Level 3 Expert

1316 Answers

quennie732

Level 2 Expert

422 Answers

Bernard D'Souza

Level 2 Expert

163 Answers

Are you a Ricoh Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...