Question about Haier BC112G Wine Cooler

Open Question

Lights on temp display flash. Why isn't the compressor running?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a wiring diagram for Delphi delco am FM CD player from a 2004 Chevy malibu


According to http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=2&ved=0CDMQFjAB&url=http%3A%2F%2Fwww.aircommand.com.au%2Fdocs%2FIbisTechManual.pdf&ei=29JPVfO8NYu9sAWE_YGQAg&usg=AFQjCNEPb_nNaXQsRrD2ZphXVLpRYwECGQ&sig2=cHErjmhdOfyCsep25gpmfw

E4: Indicates lack of refrigerant, or the compressor is not running, or the thermistor is out of calibration. Action: Check that the compressor is running by listening. If it is apparent that the compressor is running, then check the temperature difference across the evaporator. i.e. Measure temperature of return air at inlet filters and measure temp. of discharge air at grilles. This temp diff. should be 14 to 18 C. with fan on hi speed. If temp diff. is less than this, suspect lack of refrigerant. Fit a suction gauge to access valve at rear of unit. See fig 12. On a 35C outside temp. then suction should be 380 to 450Kpa.
Page 2
Action (continued) If the temp. differential is 14C or more but unit goes out on E4 after approx. 30 minutes, please check the actual thermistor temperature by the following procedure. With the inside fan running on Hi. Press Temp down button followed by the mode button. Hold them both in for approx 5 seconds. The amber Lock LED illuminates. Now press the Temp down button and the Sleep button Together for about 1 second. The green Med speed will be Flashing. The display is now reading the temp of the outside coil. Now press the Temp up button once. The Green Hi speed will be flashing. The display is now reading the temp. of the inside coil. This temp will usually be from 5 to 12 C. If it is above 24C. It is another indication of lack of refigerant. If on the other hand the air on /air off differential is 14C or greater then suspect the thermistor itself to be out of calibration. Check the thermistor as per an E1,E2 or E3 failure by measuring its resistance. See fig 19 and referring to table 1.

May 10, 2015 | 2004 Chevrolet Malibu

1 Answer

Kenmore AC window unit model 253 70151 cuts on and off.


Circuit board could be the problem but compressor needs to be checked and there might be a loose electric connection or high voltage causing the ac to trip

Apr 04, 2014 | Heating & Cooling

1 Answer

Flashing start light


see this causes and fix it. God bless you
Drain Pump If lights are flashing on the control panel, the drain pump might not be working properly. For two-wire drain pump motors check them for continuity using an Ohm meter. If it's defective YOU'LL need to replace it. Drain pumps are not repairable.
Heating Element If lights are flashing on the control panel, the heating element might have burned out. The heating element heats the water up to operating temperature. After a set amount of time if the temperature isn't reached a light on the control panel might start flashing. The heating element can be checked for continuity with an Ohm meter.

Heating Element Assembly If lights are flashing on the control panel, the heating element assembly might have burned out. The heating element assembly heats the water up to operating temperature. After a set amount of time if the temperature isn't reached a light on the control panel might start flashing. The heating element assembly can be checked for continuity with an Ohm meter.

Touchpad and Control Panel If the lights are flashing on the display the entire touchpad and control panel assembly might be defective. If the display works but the dishwasher functions are all out of synch, or some of the buttons don't respond properly the entire touchpad and control panel might need to be replaced
Touchpad If the display lights are flickering for no reason, the touchpad might need to be replaced. Sometimes when the touchpad is defective the display lights are flashing randomly.

Check Fault Codes If the display lights are flashing and there is an error code in the display window, check the Error Codes guide on our website to determine which component has failed or is failing


10_3_2012_12_23_03_pm.jpg

Oct 03, 2012 | Dishwashers

1 Answer

We have a whirlpool quiet partner iii. It was working fine and was opened mid cycle. Then it wouldnt drain. Then all the lights started blinking. At some point it drained the water out. We flipped the...


see this causes and fix it. God bles you
Check Fault Codes If the display lights are flashing and there is an error code in the display window, check the Error Codes guide on our website to determine which component has failed or is failing

Touchpad If the display lights are flickering for no reason, the touchpad might need to be replaced. Sometimes when the touchpad is defective the display lights are flashing randomly.

Touchpad and Control Panel If the lights are flashing on the display the entire touchpad and control panel assembly might be defective. If the display works but the dishwasher functions are all out of synch, or some of the buttons don't respond properly the entire touchpad and control panel might need to be replaced.

Heating Element Assembly If lights are flashing on the control panel, the heating element assembly might have burned out. The heating element assembly heats the water up to operating temperature. After a set amount of time if the temperature isn't reached a light on the control panel might start flashing. The heating element assembly can be checked for continuity with an Ohm meter.

Heating Element If lights are flashing on the control panel, the heating element might have burned out. The heating element heats the water up to operating temperature. After a set amount of time if the temperature isn't reached a light on the control panel might start flashing. The heating element can be checked for continuity with an Ohm meter.

Drain Pump If lights are flashing on the control panel, the drain pump might not be working properly. For two-wire drain pump motors check them for continuity using an Ohm meter. If it's defective YOU'LL need to replace it. Drain pumps are not repairable.
10_3_2012_12_29_03_pm.jpg

Oct 02, 2012 | Dishwashers

2 Answers

Who makes the thermostat for model #msr49nm


Isn't 37 ok? Check the condenser is clear and clean before replacing thermostat

Apr 24, 2012 | Turbo Air MSR-49NM Refrigerator Commercial

1 Answer

When idling, a/c blows hot. New compressor installed. But whwn driving it blows cold


Hello,

Check the fan. Some systems have a separate fan for the AC when running. If it isn't running when up on temp, check fuses, and the fan. If good, check sensor and relay.

--W/D--

May 31, 2011 | Air Tools & Compressors

1 Answer

We have a Kenmore Elite 79577554600 Refrigerator. The temperature display is freaking out. The numbers keep changing, lights flashing on and off, temperature counting down from 44.


It is running in "store-demo" mode. Fancy light-show, and the compressor turns off (bad!)
Hold down the right-most two buttons (Ice and refrigerator temp) for about 5 seconds. I think the right-door needs to be open for this to work, but not sure.
This will activate the fridge once again.

Dec 24, 2010 | Kenmore Elite TRIO® 7854 (25 cu ft) Bottom...

1 Answer

The control panel flashes "EC" where the fridge temp is displayed. The word "service" is also flashing.


"EC 50" means excessive refrigerator compressor run time. What is the serial number? Is the condenser fan running? Can you feel airflow from the left side up top? Is the strip between the fridge and freezer hot to the touch?

Mar 10, 2010 | Sub-Zero 680 / F

1 Answer

Lights are on but compressor won't work. Less than 2 years old.No display on temp control.


http://www.acmehowto.com/howto/appliance/refrigerator/refrigerator.php
. Cut everything off for a few minutes then turn it back onand listen for a click from the compressor relay as the compressor tries tostart.
Is the compressor motor running.If no check starter/overloadrelay.

If the relay is ok the problem is the compressor which normally has a five year warranty.

Oct 16, 2009 | Kenmore 16.7 cu. ft. / 473 liter Upright...

2 Answers

Compressor not running, front display flashing "CF"


have you tried to see if your getting voltage at compessor?? it sounds like relay/overload is bad have you replaced it?

if not, try that i'm suspecting that's the problem

Apr 23, 2008 | Kenmore 44103 Side by Side Refrigerator

Not finding what you are looking for?
Haier BC112G Wine Cooler Logo

Related Topics:

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Haier Furniture Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

jasbo
jasbo

Level 3 Expert

2239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Haier Furniture Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...