Question about Sharp EL-1197PIII Calculator

Open Question

The little plastic cover on my print cover is broken

This is the one that has rigid teeth to be able to tear the paper

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Husqvarna viking model 980


You may have the tension set too tight or are not using the correct needle. Or, the bobbin thread may not be the same as the top thread. Also, here is a little trick. Put a piece of typing paper under the edge of the material and sew across the paper onto the material on all edges that you sew off of, to give a little stability to the material. This usually works and you can tear it off gently when you are finished sewing. Also, if the tensions are o.k., try using a ballpoint needle.

Dec 18, 2015 | Husqvarna Sewing Machines

2 Answers

When I print a multiple page document on tear paper roll, the first page prints correctly but the pages after that start printing too near to paper tear size or up to paper tear size. What should I do


Sounds like your top margin is not either not set properly or your documents do not have page feed command at the end. Are you sure you have the correct driver installed?

Nov 23, 2014 | Epson Dot Matrix LQ-2090 Printer

1 Answer

HOW DO I MAKE THE PAGE ADVANCE AUTOMATICALLY TO THE POSITION I NEED IT TO BE TO TEAR OFF ?


Setting Top of Form, Forms Tear-Off ON

(Step A)

! If you turn the platen knob when the printer is turned

on, you will cause the Top of Form to mis-align. Always

turn the printer off before turning the platen knob!




1 Turn the printer ON.

2 Park the paper.

3 With paper out of the unit, (red alarm light should be on)

press SHIFT (1) and QUIET/TOF (5) to reset the current

Top of Form.

4 Press FF/LOAD (3) to load the paper.

5 Press SEL/MENU (6) to take the printer off line.

The SEL light goes out.

6 Wait until the paper moves up to the tear position, then

press and hold TEAR (4).

The paper moves to the current Top of Form.

Keep pressing and holding TEAR.
7 Press and hold SHIFT and release TEAR.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Jan 26, 2011 | OKI MICROLINE 320 Turbo Matrix Printer

1 Answer

There is still error 2 even after restart the printer (canon mp145). How to reset this error?


(remember to vote this solution plz)

Hi there,

I use a Canon MP210 myself, its a Pixma like yours. Anyways, Error 002 or 02 means theres a paper jam. Sro if you can fix that jam it will go away. If your looking at the printer and you cant see any jams still, the printer still thinks it is jammed, so heres what I would do.

  • Turn off the printer.

  • 3

    Remove any paper trays. Inspect them for wrinkled or damaged paper.

  • 4

    Open any other doors that give access to the printer's paper path and to the toner or ink cartridge.

  • 5

    If necessary, remove the toner or ink cartridge. Place it in a bag or away from light to avoid damaging it.

  • 6

    If you find a piece of jammed paper, remove it by holding it with both hands and pulling firmly (see A). The goal is to keep the paper from tearing. If several pieces are jammed together, try pulling out the middle piece first to loosen the jam.

  • 7

    If the paper does tear, try rotating the roller gears manually to free the paper (see B). Don't force anything, though.

  • 8

    Replace the toner or ink cartridge and paper trays, close any doors you opened and turn the printer back on.

  • 9

    If the printer paper jam message still appears, then there is still some paper in the printer. Reinspect the paper path.


  • Still? Take a cereal box of cardboard (cut the back/front , push that through the paper trayand get your hand on the other side and work it like your flossing your teeth)


    Yes that works.


    Thanks


    Rhos Barnes, MCSE, CCNA

    Squamish, BC

    rhos_2k@yahoo.com

    Jan 23, 2011 | Office Equipment & Supplies

    1 Answer

    I own 2 rigid drills and 4 batteries and only 1 will hold a charge. Both drills are less than a tear old. My email is: drum_mom18@yahoo.com


    The batteries can be rebuilt (not cheaply though) by contacting: www.primecell.com for details. Hope this helps!

    Jan 16, 2011 | Garden

    1 Answer

    Thanks! I have a 7x Crosscut Paper Shredder, Model # PCUA:29053U. The teeth are jammed due to I believe a build up of paper. I have run it on reverse & tried to pick out the paper. The motor runs but...


    If the motor runs but the cutting teeth dont turn then you have stripped or broken a gear in the drive train. You can get replacement parts from Royal at 1-800-524-0799.

    Oct 19, 2010 | Royal Office Equipment & Supplies

    1 Answer

    THE DRIVE GEAR FOR THE PAPER TRAY IS BROKE


    The gear drive is located in the paper tray lift motor assembly. The gears teeth strip away with wear and tear and can no longer lift the tray to feed paper. Replace this assembly and not just the gear.

    Oct 14, 2009 | Ricoh Aficio MP 161 Black and White Copier

    4 Answers

    Auto Tear off for Epson LX300+


    friends
    you have to get the exact page size of your continuous paper. then you go to start -> printer and faxis -> then go to file -> and server properties.then create one paper which is exact sixe of your paper. Then go to printer preferances and select that paper.

    to switch on tear off refer manual.

    Hope this can solve the problem.

    Feb 27, 2008 | Epson LX-300 Matrix Printer

    1 Answer

    How to set tear off?


    usually the setting to arrive at the tear off is to allow the tracter paper to arrive at the correct spot using the Top of Form using the buttons on the front

    Feb 25, 2008 | Epson LQ-2180 Dot Matrix Printer

    2 Answers

    Printer does not work


    Where is paper getting stuck/ torn

    if rear
    fuser needs to be replaced job for tec.
    a07fa03.jpg INFO

    Sep 25, 2007 | Brother HL 1440 Laser Printer

    Not finding what you are looking for?
    Sharp EL-1197PIII Calculator Logo

    Related Topics:

    95 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Sharp Office Equipment & Supplies Experts

    Anthony Karuku

    Level 2 Expert

    268 Answers

    amir hamza
    amir hamza

    Level 2 Expert

    318 Answers

    k24674

    Level 3 Expert

    8081 Answers

    Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...