Question about Boating

1 Answer

When tilting the motor down it jumps and bangs until it gets to the trim pistons, what is causing this?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 9,098 Answers

Power Tilt and Trim Maintenance Makes a Difference ...

yamahaoutboards.com/.../power-tilt-and-trim-maintenance-makes-differe...
Tilt and trim adjust the angle of the motor and thus the running surface of the boat, ...the grip on the water, the ability to jump on plane and many other operations ... be around the base of the ram, or drip down around the power tilt and trim motor. ...Sometimes you can bang on the power tilt and trim motor with the head of a ...

Posted on Jan 10, 2016

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an oil leak in one of my trim pistons


best answer is take itto local dealer and have a new seal put in.

Oct 19, 2014 | Boating

1 Answer

Tilt and trim wont trim up taking off works fine running down the lake


Check trm/tilt release screw,does trim motor run but motor doesn't lift,if trim motor doesn't run then it's probably trim solenoid/relay

Oct 09, 2014 | Boating

1 Answer

Will low fluid level cause power trim/ tilt go not hold position


Low fluid level will cause it to fail to actuate and not go up or down, can also let it not hold position as well. Filling to proper leevel with specified lubricant is recommended. If you allow the level to go too low, the pump will pull air and could burn out.

Sep 21, 2014 | Yamaha Tilt Trim Motor, 40-90 HP Outboards...

1 Answer

How do I replace the motor on a yamaha power tilt and trim 1995


loosen engine mounting bolts and steering tube , trim engine up by releasing the valve on the side and tie up so not tocome down ! remove pin on the ram then remove all bolts and wires and should come out !

Jul 20, 2014 | Arco Yamaha Outboard Power Tilt and Trim...

1 Answer

Tilt/Trim Motor


check trim switch with multi metre ! check solinoids not stuck !

Jan 16, 2014 | Boating

1 Answer

1978 evinrude will tilt up but not down


Sounds like something is wrong with your tilt and trim motor. You can find some replacements below.

http://www.iboats.com/Evinrude-Power-Tilt-and-Trim-Motors/dm/view_id.269667

Apr 16, 2013 | Boating

1 Answer

Tilt trim go up wont go down 2003 johnson 140 hp 4 stroke


You may want to check service bulletin #2002-052. Some of these motors supply too much voltage to the trim switch at the throttle lever and that trim switch stops working. There is an add-on harness #586806 that fixes this. If you can still tilt and trim the motor at the trim switch that is built into the motor housing this is likely the problem.

Jan 30, 2012 | Boating

1 Answer

I have a 1994 150 hp Yamaha outboard motor with tilt-trim. My motor is stuck in the up tilt position and will not tilt down. It is working when I go up, but not down. I have talked to a used parts dealer...


Stop! Dont replace the pump...I would bet that it is the "down" Solenoid that went haywire. I would begin by replacing the Down solenoid...it is a far easier and cheaper fix and if your pump works to raise the engine then that tells me that it is not faulty. The Down solenoid looks just like a starter solenoid and the one that you are looking to replace has a GREEN wire to it. Yellow with a red stripe is for the starter. Blue wire is the up solenoid. So replace the one with the green wire going to it and I bet it will fix your problem.

Jul 14, 2009 | Boating

1 Answer

Volvo-penta aq271c, trim will go down, but not up.no pwr at relay


First check the switch-- does it have power, then check the solenoid to see if it works-- there are two. One is for down, One is for up. If you get power from the solenoid-- outgoing-- check connections going to pump motor.

Mar 28, 2009 | Boating

Not finding what you are looking for?
Boating Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Boating Experts

ray gallant
ray gallant

Level 3 Expert

64733 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

29375 Answers

Tom Chichester

Level 3 Expert

54386 Answers

Are you a Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...