Question about Uniden DECT 1480-3 Black Cordless Phone w/ 3 Handsets DECT 6.0, Answering Machine, Caller ID

1 Answer

I have charged the base and the two hand sets for 48 hrs. This is a new unit. No dial tone/communication to any unit.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 50 Answers

1st-check the intercom function of the units. No intercom recheck the battery connections ,look for a clear tape on them & remove. Recharge batteries.2nd- Intercom OK. Check base connection to wall phone jack. Interconnect phone cable may be bad. Good luck. Have a nice day.

Posted on Jan 11, 2016

Ad

5 Suggested Answers

Anonymous

  • 1 Answer

SOURCE: ELBT595 Handset Not Turning On

Check the handset battery -- if there is a slight "bulge" on one side (ie: not COMPLETELY flat) then the problem is with the battery. I had that problem and had to order a new one. That said, I just installed the new battery, and while it now charges, the handset won't connect to the base unit. The base unit works (tried the speakerphone), but there is not connection between base and handset.

Posted on Apr 14, 2008

Ad

Anonymous

  • 12 Answers

SOURCE: adding a new handset

You need to register the new handset with the base.
In Global settings De-register the new handset then place it on the main base unit connected. It should then register.

Posted on May 04, 2009

goalie39

Ed

  • 479 Answers

SOURCE: My phone is dead


Reset Procedure for Cordless Phones

Question:
0.gif
What is the general reset procedure for cordless phones?
0.gif
Answer:
0.gif
1. Disconnect Battery from handset(s)
2. Disconnect Phone Cord from wall jack
3. Disconnect Phone cord from base unit
4. Disconnect AC adapter from wall outlet
5. Allow to sit for 30 min
6. Reconnect Phone Cord to base
7. Reconnect Phone cord to wall jack
8. Reconnect AC Adapter to wall outlet
9. Reconnect Battery to hanset until you click or feel the plug snap into place
10. Re-Register Handset by placing on main base in most instances.
<KEYWORDS="RESET, call,? can?t tone, dial no flashing, unavailable, range, of out working, not up, messed>

Posted on May 05, 2009

mary k harden

  • 75 Answers

SOURCE: TRU8888 Base Unit - No Dial Tone After Power Failure

get a new phone

Posted on Aug 29, 2009

John Cunningham

  • 6771 Answers

SOURCE: HEY, Just got DWX207 and it's not working. It's

When you got it do you take the back off to make sure the battery is plugged into the phone? if yes! the phone clearly has a manufacture defect and should be returned.

Posted on Mar 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced my desk phone with a wireless and I lost dialtone on all the phones


Are you saying you have a wireless desk cell telephone? Or is this a regular land line telephone with a wireless hand piece? If it is a cell phone with no dial tone, you must see your service provider - this is HIGHLY unusual. If this is a land line telephone with a wireless hand piece - be aware that the dial tone cones from your base transmitter, where ever it is located, (Normally this base should be withing 300 feet of the hand piece) and that base unit MUST be plugged into an active telephone outlet. In the USA, the standard jack is an RJ 11. I suggest you take your old telephone and plug into the outlet where your new base unit is located. Do you get a dial tone? (proves the line is good) Check all wiring - same type of contacts (for your country)? Still no dial tone? Take it back to the store and get them to demonstrate its operation for you - does it work at their store? ... if not, get a new telephone or an adjustment.

Jun 04, 2011 | Cell Phones

1 Answer

The phone lights up when put to charge also the red light on the base,, but when the phone line is connected it wont work ..What do u think is the problem?


The battery in the handset could be bad . First I would test that the base unit is recieving dial tone by pressing speaker button on base unit. If there is dial tone then problem is in handset or in base unit communication to handset. Try resetting power to base unit. Check manual for any re-initialization procedure. If the base unit is not receiving dial tone then I would test that the phone line is delivering dial tone to the base unit by connecting a known good phone to the line cord. If the dial tone is not present , problem could be in line cord from outlet, outlet, building wiring, or service provider.

Dec 08, 2010 | Uniden Cordless Phone

1 Answer

No dial tone on hand set battery is new lights up


Make sure your connection to the phone jack is secure.
Use another wired phone to make sure connection is good to your phone.
Secure connection in back of phone, and plug it in. The base MUST have power to transmit the signal to the handset even if the handset has a fresh charge.
Although the handset is normally linked to the bases, check to make sure via the instructions. To determine if the base recognizes the handset, press the "LOCATE HANDSET" button.
If the hadset responds, the links is there.

Hope this helps
good luck and don't forget to vote!!!

Sep 27, 2010 | Panasonic KX-TG2356 Cordless Phone

1 Answer

I have charged for abt 20 hrs for set up. all I get is "Searching" Help me to move foreward.Sue DECT1560 This is a new phone I am trying to get it in service. I have no dial tone ,message "searching"...


First make sure the phone jack is working by plugging a working phone into it.

if it is working, use the same phone cable to plug into the base of your new unit.

if you do not get dail tone, place the handset into the main charging base. this should sync the phone up to the base. lift it out and try again.

if you still do not get dail tone or see searching, open the phone and remove the battery. wait 30s or so, plug the battery back in and set the phone in the main charger again. wait 10second and try the phone again.



Nov 06, 2009 | Uniden DECT15602 Cordless Phone

2 Answers

Need to change phone back to tone dialing


Here's what the manual says: Changing the Dial Mode (Tone or Pulse Dialing) (HS1 only) Your phone can communicate with the telephone network in two different ways: tone dialing or pulse dialing. These days, most phone networks use a method called tone dialing, so your phone comes programmed for tone dialing. If your phone company uses pulse dialing, you need to change your phone's dial mode. If you don't get a dial tone or can't connect to the telephone network, follow the steps below to modify your phone?s settings: With the phone in standby, press and hold [cid/menu]. Press [vol/ / ] to move the pointer to select DIAL. Press [select/channel] to set the phone to pulse dialing. Press [end]. Return the handset to the base. The handset communicates the new setting to the base, and the base activates the setting on any other handsets. Hope this helps out. K

Jun 05, 2009 | Uniden 2.4 GHz Cordless Phone System

1 Answer

No dial tone


If you got this second hand more than likely the battery in the hand set is dead. Batteries Plus has batteries for EVERYTHING.

Nov 22, 2017 | GE 26928GE2 Cordless Phone

1 Answer

Problems with handsets


Are they cordless phones?If they are they get there dial tone from the base.If there is a blinking red light on the hand sets they lost communication with the base.Check your user manual to see if you need to program them to the base.

tk46

Jun 09, 2008 | Panasonic KX-TG1033S Cordless Phone

1 Answer

Handset ?No Link To Base? error and no dial tone


2/29 Have you registered or re-registered the handset?
"No link" can mean handset is not accepting radio wave of base unit. At Mfgr website pull-down operator's manual and look for registration instructions. Some sequence of buttons will create a radio signal from base (have handset off base) then another sequence of buttons on handset will accept radio signal. If handset has "menu" button, try "menu", then "00" (zero zero) then select an accept or "OK" button. Good luck.

Jan 14, 2007 | Xact Communication XG2200 Cordless Phone

2 Answers

General problems


do not disturb feature has to be disabled

Sep 21, 2006 | Uniden Cordless Phone

Not finding what you are looking for?
Uniden DECT 1480-3 Black Cordless Phone w/ 3 Handsets DECT 6.0, Answering Machine, Caller ID Logo

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Lands Phones Experts

Cindy Wells

Level 3 Expert

6073 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

martin hogg

Level 2 Expert

157 Answers

Are you an Uniden Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...