Question about Amana Dryers

1 Answer

Buttons all work but drum will not spin and it shows code f01

Model#ned7500vmo

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 90 Answers

You dont mention make! Does it start program then shut off or does it fill then not turn? First part of any program is to pump out any water left from it previous program .if something is blocking pump (bra wire/coins/hair bobble etc) it will shut down and putup a code.if its the brushes in the motor or belt broken it will start then pump then fill then may carry through whole program as it doesnt know its drum isnt spinning.or it will detect and show fault code.replacing brushes in motor is for somebody who knows what theyre doing.but its straight forward and brushes are cheap. Pumps blocking again common but most people can clear a blockage via a door at bottom of machine.water will ome out so take drain tube and hold in a bucket at ground level first

Posted on Jan 18, 2016

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Amana dryer model # NED7500VMO Dryer wont work, error code F01


Disconnect all the plugs from the main control board and plug them back in to be sure you have good connections, if this doesn't work... order part # WPW10174745 Amana Dryer Main Control Board WPW10174745

Jul 14, 2016 | Amana Dryers

1 Answer

Sears Electric Dryer is flashing F01 What is wrong?


The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.
You can order a new control board from the Sears PartsDirect website.
http://www.searspartsdirect.com/partsdir...
Here's how to do it: http://media.fotki.com/1_p,wkwdftgtbkdgf...


Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Feb 04, 2016 | Sears Kenmore Elite Electric Dryer 69278

1 Answer

Why is my Maytag Epicz model #MGDZ600TW2 not starting amd giving me an error code F01. What does it mean?


F01 is a control unit failure does this come up when you push the start button or did you go into diagnostic to get this code I have seen it come up as a false code check the start button does it spring back like all the other buttons if so replace control if not the button is broke

Jan 29, 2015 | Maytag Dryers

1 Answer

MAYTAG 3000 F01 CODE


It's probably a weak or failed component on the board. It's a common issue on those machines and the Whirlpool Duets. It's usually burned at the motor relay or heater relay.
F01 error code flashes when there is a primary control failure.
The only thing which will solve an F01 error code is a new machine control board. These is a catastrophic control board failure. Nothing can correct it. The part number you require is W10205977.

Dec 17, 2013 | Maytag Dryers

1 Answer

Error code f01


all I can say to that is if you arrange the bath rugs in a balanced way so they are equally distributed then the problem should go away eric

Dec 29, 2017 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

The washer will not start. It reads an error code F01.


The only thing which will solve an F01 error code is a new machine control board. These is a catastrophic control board failure. Here is the board to order.

Nov 05, 2012 | Maytag Epic Z and Performance Series 2000...

1 Answer

Hotpoint wmf 940


hi shaun, i think this fault is connecting block attaches to the motor 1 of the wires may have broken off where just clean the wire and resolder it back on hope it helps

regards
shaun

Nov 10, 2011 | Washing Machines

1 Answer

When time to drain pump drains water then just hums and it wont spin, get error code f01. when i turn dial to drain and spin pump just hums drum might turn a little but it never spins. i have emptied...


f01 is main controller (board) failure.
Replacing it is the only solution.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Sep 07, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Washer won't start. Error code f01 shows.


Hi F1 means your CCU is bad and needs to be replaced sorry :( If you have any other questions please feel free to comment again. Mike e63dqt.jpg

Nov 19, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Will not spin under load


F01 - There may be an internal problem with the control, attempt a Hard Reset.

Hard Reset - In some cases the control can be non-functioning or may not accept activation from the control panel. To clear and restart the control follow the these steps:

* Unplug or turn the circuit breaker off for 30 seconds.
* Reconnect the unit to the power source by turning the breaker back on or plugging the unit back into the wall outlet.
* Press the Pause/Cancel/Stop button twice to clear the "PF" in the display.
* Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts.

The F01 generally indicates a failed electronic machine control board.
This error code can sometimes be caused by a glitch or power surge through the electrical lines.
You may be able to clear this code by unplugging the washer for 5 minutes.
If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.

The procedure for accessing and replacing this control board is shown in this image...

http://media.fotki.com/1_p,wkwdftgtbkdgfrwxgtqsskgwtqkq,vi/ksrttqdqrxkssrqtgsd/1/1303472/5961857/image12917img-or.jpg

Be sure to unplug the washer before accessing internal components.
When you access the control board, I recommend transferring the wires from the old control board to the new replacement control board one connection at a time.
Once you have all of the wires transferred, remove the old control board and mount the new control board in the washer.
Reassemble and test the washer.

The "F01" error code indicates a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU.
The "F01" can also be displayed if the onboard "Pump Driver" fails to activate.
Generally in order to correct this failure will require replacing the CCU.
There is no way to test and verify if the control board has failed.
The technical data sheet basically states to replace the CCU.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Oct 15, 2009 | Kenmore HE2 Plus Front Load Washer

Not finding what you are looking for?
Dryers Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Dryers Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

jdthefixer

Level 3 Expert

746 Answers

Android Man
Android Man

Level 2 Expert

278 Answers

Are you an Amana Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...