Question about Hitachi Heating & Cooling

2 Answers

Hitachi Split AC. Turn on the mains, the fan turns on for few second then the filter clean red LED starts blinking and AC goes dead. Only the power light is on and red LED is blinking (5 times & puase

Hitachi Split AC. Turn on the mains, the fan turns on for few second then the filter clean red LED starts blinking (five times & pause) and AC goes dead. Only the power light is on and red LED is blinking.No Response to remote control after the red LED starts blinking. Model : SPLIT AC - 0.9T CLASS HITACHI SAC KAZE - RAU010KQD What could be the problem ?

Posted by on

  • Sk Sujabuddin
    Sk Sujabuddin May 21, 2019

    Same problem any body help

  • Girish Mohanty Jun 18, 2019

    Hitachi Split AC. Turn on the mains, the fan turns on for few second then the filter clean red LED starts blinking and AC goes dead. Only the power light is on and red LED is blinking.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hitachi Master
  • 10,679 Answers

If filter clean hold down filter button on remote to clear

Posted on Apr 10, 2018

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,410 Answers

Possibly the filter...

If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

Posted on Sep 30, 2017

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

mr1967mejias

FastHarley

  • 751 Answers

SOURCE: Hitachi split air conditioner. I turn on the

Clean filters and reset.

Posted on Nov 23, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HELLO i HAVE THE mITSUBISHI wd60737 AND IT WILL NOT TURN ON. IT BLINKS THREE GREEN LIGHTS LIKE IT GOING TO TURN ON BUT THEN IT BLINKS RED ONCE AND TURNS OF. i TRIED THE HOLD FOR TEN SECONDS RESET THIN


First make sure the filters and vents are clean and the filter cover(s) are properly installed.

Try once more (DO NOT RESET). As soon as the TV shuts down, press the ACTIVITY/ENTER button and the CH Down button on the TV (not the remote control) and hold them for 5 seconds. The Status LED will start blinking an error code. The "normal" code is 12, which would be one blink, pause, then two blinks and a pause. The code is repeated five times. Post your results in the comments; I can look up the code for you.

Jan 03, 2015 | Mitsubishi Televison & Video

1 Answer

Nec vt540 vt540k


probably needs filters cleaning or a new lamp replacement.

Oct 07, 2013 | NEC VT460 Multimedia Projector

2 Answers

AC power light blinks but not starts


The outside unit has a problem. Have it tested.

May 05, 2017 | Hitachi Heating & Cooling

5 Answers

LED LIGHT BLINKING OF HITACHI SPLIT AIR CONDITIONER


Did you figure out why the ac wasn't responding to the remote? I am having the same problem. I just cleaned out the filters but it's still not responding to the remote. I have already tried reset button in the remote, which didn't help. I am pretty sure that the remote is not out of battery.

Jun 18, 2012 | Hitachi Heating & Cooling

3 Answers

RED LIGHT BLINKING IN HITACHI ICLEAN AC.. WHAT TO DO?


I was told the same thing that Dennis has posted by the guy who came to service the AC. So I think, it is ok as long as it blinks 9 times in a row and then repeats it after a brief pause.

Jun 08, 2012 | Heating & Cooling

1 Answer

I have a Sony KDS-R50XBR1 that has no picture. When I turn on the TV, the green Power/Standby LED light blinks for about 30 seconds, then turns red and blinks five times. The Power/Standby LED repeats...


  • Five blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK blanking, try turning up screen A2 slightly.

Jan 19, 2011 | Sony KDSR50XBR1 50" Projection HDTV

1 Answer

My hitachi plasma tv model: p55t551 every time i


turn tv on the red power light comes on then goes off again

Jun 27, 2010 | Televison & Video

1 Answer

My d530 minitower powers off unexpectedly and red lights starts to blink on System's LED//


Hi Kindly let me know how many times the red light blinks
Condition Code Service Actions Processor thermal protection activated. Power LED blinks red twice, once a second, followed by a two second pause.
  1. Make sure the computer air vents are not blocked and that the cooling fan is running.
  2. Open the hood, press the power button, and see if the processor fan spins. If the fan is not spinning, make sure the fan cable is plugged into the cable header on the system board, and that the fan is properly installed and seated.
  3. If the fan is plugged in and seated properly, but is still not spinning, replace the processor fan.
  4. Reseat the processor heatsink and make sure the fan assembly is attached to the heatsink properly.
Processor is not installed. Power LED blinks red three times, once a second, followed by a two second pause.
NOTE: This condition indicates a missing or improperly installed processor, not a defective one.

Make sure there is a processor in the system. Reseat the processor and verify that it is installed properly. Power failure (power supply is overloaded) Power LED blinks red four times, once a second, followed by a two second pause.
  1. Check the voltage selector, located on the rear of the power supply, is set to the correct voltage (the correct setting depends on the region).
  2. Open the hood and make sure the 4-wire power supply cable is fully connected to the power connector on the system board.
  3. Check if a device is causing the problem by removing all attached devices (such as disk drives and expansion cards), then power on the system. If the system enters POST, power off and replace one device at a time, repeating the procedure until the system power failure reoccurs. Replace the device that caused the failure, then replace each of the other devices and confirm that they are functioning properly.
  4. If you cannot isolate the failure to a specific device in the previous step, replace the power supply. **
  5. Replace the system board.*
Pre-video memory error. Power LED blinks red five times, once a second, followed by a two second pause, and five simultaneous beeps are sounded
  1. Reseat the DIMMs in the memory slots on the system board, then power on the system.
  2. Replace the DIMMs one at a time to isolate the faulty module.
  3. Replace 3rd-party memory with HP memory.
  4. Replace the system board.*
Pre-video graphics error. Power LED blinks red six times, once every second, followed by a two second pause, and six simultaneous beeps are sounded. For systems with a graphic card:

  1. Reseat the graphics card and then power on the system.
  2. Replace the graphics card.
  3. Replace the system board.*


For systems with integrated (on-board) graphics, replace the system board. PCA (system board) failure. ROM detected failure prior to video. Power LED blinks red seven times, once a second, followed by a two second pause, and seven simultaneous beeps are sounded. Replace the system board. Invalid ROM based on bad checksum Power LED blinks red eight times, once a second, followed by a two second pause, and eight simultaneous beeps are sounded.
  1. Reflash the ROM using a ROMPaq diskette.
  2. Replace the system board.*
System does not power on. No beeps or blinks since the system is not functioning. Press and hold the power button for less than four seconds. Perform the following steps depending on whether the hard drive LED turns green.

If the hard drive LED turns green, then:

  1. Make sure the voltage selector (which is located on the back of the power supply) is set to the correct voltage for your region.
  2. Remove the expansion cards one at a time until the 3.3V auxiliary light on the system board turns on. If removing a card turns the light on, replace the card and then see if the system works.
  3. Replace the system board.*


If the hard drive LED does not turn green, then:

  1. Make sure the computer is plugged into a functioning AC power outlet.
  2. Open the hood and make sure the power button is securely fastened in the power harness and that the harness is connected properly to the power connector on the system board. In other words, make sure that the power button is making contact with the power circuit.
  3. Make sure the power supply cables are connected properly to the power connectors on the system board.
  4. Check to see if the 3.3V auxiliary light on the system board is not turned on, replace the power supply. **
  5. Replace the system board.*

Dec 29, 2009 | HP Compaq d530 Convertible Minitower PC...

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

1,052 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Heating & Cooling Experts

Lawrence Oravetz

Level 3 Expert

10543 Answers

jws1013

Level 3 Expert

1669 Answers

bobalix

Level 3 Expert

471 Answers

Are you a Hitachi Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...