Question about Magimix 5100 Cuisine Systeme Food Processor

Open Question

The add on stick (on wic you put te blades) is stuck on. Wife pressed too hard and cant pull it off- suggestions please

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont my chopper blade come off in the unlocked position?


Help! My Cuisinart is Stuck! - Chowhound

www.chowhound.com/post/cuisinart-stuck-353459
Dec 21, 2006 - Read the Help! My Cuisinart is Stuck! discussion from the Chowhound food community. ... The lid seems stuck and won't come off. I've tried pressing down,... Make sure all the buttons are in the neutral position. Reply ... In case of clarification- Turn the lid back on before unlocking, then twist off. Reply.

How to remove a stuck Kitchenaid Food Processor Blade (blade in ...

https://answers.yahoo.com/question/index?qid...
Aug 25, 2009 - Now the blade in the smaller bowl (4 cup) does not come off the bowl.... UNless i take out the 4 cup bowl blade, it doesnt allow me to remove the bowl ... I've used the screwdriver method for years in my shop with nearly 100% ...

Jan 12, 2016 | Food Processors

1 Answer

Food processor blade stuck on motor shaft


my friend if you had not removed that blade for a while it will certainly stuck due to the moisture that forms on the shaft of the blade holder causing it to have corosion you will have to carry that item to be removed by a qualified tech by you doing it your self could cause damage,which could cost you more.good luck

Jun 16, 2007 | Cuisinart DLC-5 Food Processor

1 Answer

NEED REPLACEMENT BOWL AND METAL BLADE


place one foot on it and pull it out or you can try to wiggle it out

I’m happy to help further over the phone at https://www.6ya.com/expert/taisean_6df1de1d23f88296

Jan 22, 2014 | Wolfgang Puck BFPR0015 Food Processor

2 Answers

Good Evening, I cant get the circular blade to release from the stem. Any suggestions.


Good evening to you!!! Two q's? which way are you turning it and are you using your super special blade holder?

Remember, Off will be in the direction of blade rotation. It may be snug because it tightens when the the blade turns. Please make sure it's unplugged. Not funny and don't say it doesn't happen. Good Luck, Ned

Oct 06, 2009 | Wolfgang Puck Food Processor

1 Answer

Cuisinart DLC-7--blade stuck--cannot remove from bowl.


First off, is it a BLADE that's stuck, or a DISC?
If it's a disc, and the disc is blocking your access to the center post, put a ziploc baggie full of ice on top of the disc (right in the middle) and let it sit for about half an hour. That should shrink the plastic enough to pop it out.

If it's a blade, you can try the ice trick, or you can try Pam (or another food grade cooking spray) to loosen it up, and then just try to take the workbowl off like you usually would (aka, DO NOT grab the blade, or you'll risk cutting yourself--you can just pull up on the bowl, and the blade should pop off.

If you need further help, you can always contact Cuisinart--their phone number (according to their website, www.cuisinart.com ) is 1 800 726 0190



Good luck! :)

Aug 31, 2009 | Food Processors

1 Answer

Magimix blade is stuck


You need to replace the spindle i'm afraid which gets worn after a time. There a UK company that sells replacements and tells you how to replace it. Not a big job though a bit tricky. magimixspares.com

Jun 28, 2009 | Magimix 5100 Cuisine Systeme Food...

1 Answer

Braun blender blade stuck in the jar and cant seem to take it out


Some bike locks go through the wheel and are about six inches long and are tempered. you can insert it in blender between the blades and use a pipe or screwdriver to apply leverage without having to get near cutting surface with body parts

Mar 02, 2009 | Braun K 750 CombiMax Food Processor

1 Answer

Kneading blade stuck


plz contact 022-23051554 /23095757

Feb 02, 2009 | KitchenAid KFP750 Food Processor

2 Answers

Stuck dough blade


On the DLC 7 Pro cuisinart the blade was removed by removing
the plastic bottom. Make sure the unit is unplugged. Remove the four rubber pads on the bottom. This was the hardest part because the pads are glued so securely that the inner rubber surface tears as it's removed. I used two flat blade screwdrivers and worked carefully, back and forth. Using a #2 philips, remove the four screws. Place the unit on its side and while inserting a screwdriver between a spoke and the motor frame gently turn the blade counter clockwise. Be careful not to put pressure against the cooling fins. Very little pressure was needed and the blade came right out. I might have been able to hold the shaft from turning without removing the bottom, by going through the vent slots in the bottom, but I was concerned with cracking the plastic. To replace the rubber pads I matched the design of the torn rubber pad with the shape (design) of the surface glued rubber and used thin two-sided tape.

Dec 27, 2007 | Cuisinart DLC-5 Food Processor

1 Answer

My food processor just stopped working?


A Cuisinart food processor doesn't start before the top is assembled properly, that is a safety feature. Their strong motors can withstand also hard to cut ingredients.

Aug 27, 2007 | Cuisinart DFP-14BC Custom Food Processor

Not finding what you are looking for?
Magimix 5100 Cuisine Systeme Food Processor Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Magimix Food Processors Experts

Ross Keen

Level 3 Expert

1361 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

29395 Answers

Ruth summersides

Level 3 Expert

1477 Answers

Are you a Magimix Food Processor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...