Question about Hyundai Vehicle Parts & Accessories

1 Answer

Code p0700 for hyundai elantra 2010 - Hyundai Vehicle Parts & Accessories

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Hyundai Master
  • 9,462 Answers

Looks like it's hard to get..
why don't u try online
some websites deal in it real time.. along with solutions to problems how to repair fix service nd all

Posted on Jan 28, 2019


6 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



  • 115 Answers

SOURCE: P0139 code for a 2003 hyundai elantra. What is this code?

Hi the code P0139 is Bank 1 sensor 2 lambda sensor fault ,possible wiring or sensor fault even if you replace the sensor you need to have the MIL lamp turned off by a Diagnostic machine,it is possible you have another fault such as poor Catalytic converter efficency giving the same fault code ,Would recomend you get the car checked and read the "live" data as the car see`s it to make an accurate diagnosis and cure

Posted on Jul 10, 2009

Car Fixer

  • 184 Answers

SOURCE: 2003 Hyundai Elantra GLS. Check engine light, code PO133

Did you use a aftermarket O2 sensor or a genuine Hyundai one? If it's an aftermarket one it may be bad or not as good as the OEM one. See here for more details and other potential causes: P0133

Posted on Feb 11, 2010


ZJ Limited

  • 17970 Answers

SOURCE: need fil for error code P2626 Hyundai Elantra GLS

P2626 O2 Sensor Pumping Current Trim Circuit/Open (Bank 1 Sensor 1)

I'll sure this has to do with a faulty O2 sensor. This sensor is usually located around the header of your car, or down more on your exhaust.

Try disconnecting your battery for 30 mins, hook it back up, and start your car again. This will erase the error. See if it comes in again.

Hope this help (remember rated this post).

Posted on Mar 25, 2010


  • 834 Answers

SOURCE: trouble code 1997 Hyundai Elantra, P1128

P1128 trouble code is for (Upstream Heated O2 Sensors Swapped). Did you switch around any of the O2 sensors?

Posted on Apr 24, 2010



  • 4803 Answers

SOURCE: how do you take the front driver side door panel

It is pretty easy, but care must be taken so as to not damage the door panel. I recommend purchasing a door panel clip removal tool for this purpose. They are available at most parts retailers for just a few dollars. Using these tools to relaese the plastic clips on the door panel can save you a lot of aggravation and expense.

> Remove the triangular-shaped cover that covers the inside portion of the door mirror mountings. It simply "un-clips".

> Remove the screw that retains the bezel over the indide door release handle and remove the bezel.

Remove the two scres retaining the door panel to the door frame. One is under the triangle cover behind the mirror that you removed, and the other goes straight down into the pocket of the door pull.

Then use the special door clip release tool (recommended) or another suitable tool to pop the clips loose around the perimeter of the door panel. Lift out and up to remove door panel.

Installation is the reverse order.

Posted on May 28, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2006 hyundai elantra hard shifting put new output and input sensors now it is lack of power and still shifts hard but not as bad light came back on codes p0700 p0722

code p0700 is TCM problem
code p 0722 is output shaft speed sensor--no signal===causes --wiring--OSS sensor --TCM ---ECM
possible that your problems are wiring and connections and /or transmission control module (TCM)

Apr 03, 2018 | Hyundai Cars & Trucks

3 Answers

PO-139 I had that sensor change 3 weeks ago and the check engine light came on again this morning.Thanks

Probably replaced a good sensor. This codes could be from a bad sensor, a vacuum leak, or an exhaust leak before the sensor.

Dec 01, 2015 | 2006 Hyundai Tucson

1 Answer

I have a 2010 hyundai elantra and it is leaking water from under the dash when it rains

A 2010 Elantra?... it's still under warranty. Take it in to the Hyundai Service Dept and have it diagnosed & repaired under warranty.

Jun 28, 2011 | 2010 Hyundai Elantra

Not finding what you are looking for?
Vehicle Parts & Accessories Logo

Related Topics:

312 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Vehicle Parts & Accessories Experts

Pierre Laplante

Level 3 Expert

2042 Answers


Level 3 Expert

85216 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14809 Answers

Are you a Hyundai Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides