Question about Yamaha Ef600 Generator/inverter Repair/service Manual

1 Answer

How tob fix generator after i put too much oil in generator started for 10 secs then puff of smoke and stopped and pull cord wont move ?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 414 Answers

Try taking out your spark plug and see if it needs cleaned or replaced

Posted on Mar 05, 2016

Testimonial: "pull cord wont move as if engine has seized"

  • elaine fleck
    elaine fleck Mar 05, 2016

    pull cord wont move as if engine has seized



1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why won't Toro start - we have electric start and pull cord won't move?

pull on the bail handle tape it down try to turn blade by hand with plug removed if you can move poure a little oil end cylider and spin it sevseal times put plug back in start it i think it heat siezed check oil level to thats what us red necks do let me know

Aug 27, 2014 | Garden

1 Answer

Why won't my toro 6.5 gts start after taking blade offand replaceing it?

From flipping the mower on it's side the top of the cylinder gets slightly flooded with crankcase oil. A good priming and a few extra pulls on the starter cord is usually necessary after this type of maintenance. You'll see a few extra puff of oil smoke upon starting. This burns off in less than a minute.

Jul 15, 2014 | Toro Lawn Mower With Toro Power Tools

1 Answer

Puff of smoke from air vents.

You have a better idea than us, you saw and smelt the smoke.

Nov 01, 2017 | 2000 Ford Taurus

1 Answer

Was driving normal started smoking and wont move

You obviously have a leak, but you need to determine where.
This needs running on a rolling road - or even on stands for a bit to see if it is leaking out. It could still be filling up the bell housing with oil.
The Gearbox will need to come out anyway to fix it, so you will probably find out then.
Have the seal replaced, and a new clutch at the same time to save on labour costs.

May 04, 2010 | 1992 Ford Explorer

3 Answers

Exhaust pipe comes out white smoke when start bike on side stand

Continuous or just for the 5-10 seconds.
If continuous you may have oil seeping past your pistons oil rings or valve guides oil seals.
Check your spark plug see if they are fouled badly (covered heavily and oily) or just covered by oil and sooth lightly.
If 5-10 sec it is normal as the engine is heating up there are normally a little oil seeping past the seals.

Apr 10, 2010 | 2004 BMW R 1150 RT (ABS)

1 Answer

Husky 2600 psi Powerwasher will not start, it was only used once, in 2008. gas was left in the powerwasher over last winter. I followed the 13 steps on hooking it correctly and turning it on etc.. when I...

You may have to take out the carb and get it cleaned / air-blown out. Looks like some little valve is stuck. Also make sure you are getting enough sparks at the plug tip. If you have left it long in a damp place it may take several pulls on the cord for the engine to fire-up and run. Try spraying some WD-40 into the cylinder through the plug-hole. Then pull the cord again. After a few pulls remove the plug again, and put like a spoonful of clean 10/30W engine oil into the cylinder, and keep pulling the cord until you see some smokes at the exhaust. If the engine fires up and run a few minutes, but stops later. The engine might be out due to incorrect oil/fuel misture.

Oct 20, 2009 | Garden

1 Answer

Vtx1300, 7000 miles, burning oil, plugs look ok what do I look for next?

Assuming the engine is burning oil and not leaking it out, the most common cause is wear on the piston rings. Somewhat continuous light smoke indicates rings. A puff of smoke when starting up the engine or pulling away from a stop sign indicates worn valve guide seals.

Can I get a “very helpful” rating on this answer?

Aug 22, 2009 | Honda VTX 1300 Retro Motorcycles

2 Answers

Smoking when starting 2001 susuki grand vitara

well I figure the valve seals are a little worn ya didnt give the milage on the vehicle. also could be the oil seals too

Aug 05, 2009 | 2001 Suzuki Grand Vitara

2 Answers

89 chevy s10 blazer puff smoke out tailpipe when 1st started

A puff of smoke when you start up indicates worn valve seals.That's why all your work didn't fix the problem and it doesn't show a code. It's a pain in the --- job that requires some specialized tools so I guess it depends on how bad it bugs you,if oyu want to fix it.

Jul 13, 2009 | 1989 Chevrolet S-10 Blazer

3 Answers

Moved my rx8 yesterday.i got ack in it this

verify condition by spraying some starter fuel in should start and die if its a fuel problem.
if it still does nothing start checking any and all fuses.if all the fuses are good take out a spark plug and verify no spark.
if no spark check the ignition module.
it might be able to have it checked at autozone for free.but you will have to remove it.

Jun 12, 2009 | 2005 Mazda RX-8

Not finding what you are looking for?
Yamaha Ef600 Generator/inverter Repair/service Manual Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Electrical Supplies Experts

Sheldon Dedek

Level 3 Expert

909 Answers

John Trevino

Level 3 Expert

1420 Answers

Robert Wooley
Robert Wooley

Level 2 Expert

177 Answers

Are you a Yamaha Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides