Question about Sony Audio Players & Recorders
It's time to take it to an electronics tech. Something inside it has died, blowing the fuse. This isn't a do-it-yourself project.
Posted on Mar 10, 2016
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Sony Receiver STR-D550Z
I would open it up and look for large capacitors that have a bulged top, I've fixed several receivers that were buzzing or had static by replacing a couple of cheap capacitors that had blown.
Posted on Sep 17, 2008
SOURCE: sony str-db940
Most likely a cold solder joint somewhere in the audio circuit. Most likely on the legs of the relay that turns the speakers on or off. Also check the connections at the audio outputs. Give it a good look over for bad solder connections, given the symptoms that's 98% likely to be the problem.
Posted on Oct 06, 2008
The most common problem found on FixYa for Audio Video
My receiver say's "Protect" or turns on then off. What's wrong? Seven times out of ten it is a shorted speaker or speaker wire. To determine your exact problem, the first step is to disconnect all speaker wires "at your receiver" Next: Turn the receiver back on. If your receiver still says "protect" or turns off, it needs to be serviced. If your receiver stays on; reconnect your speakers one at a time and power back up after each speaker. You may find that after reconnecting all speaker wires it works! Most commonly the small braids of wire from the + to the - have touched and have caused the problem. In some instances, you noticed the problem only when turning the volume up. either way, make sure the exposed wires to your receiver are no longer than 1/2" long and are completely under the screw down terminal or slide in. When you've found the wire or speaker with the problem, your receiver will go back into "protect" At this point, disconnect the wire from the speaker at the speaker that may be causing the problem then test again.* Note* Make sure speaker wires do Not touch each other as this Will cause a short! If you turn the receiver back on and it stays on, you now know the problem is in your speaker itself. To test your speaker, you will need a multimeter. Set it to ohms resistance and touch the speaker terminals, if there is a short internally the meter will read "1......" If it's an analog meter, it will peg to the right. There's your problem. Now, within any speaker there are quite a few possibilities as to what could be causing the problem. Most common is a blown coil and the speaker needs to be replaced. Some speakers have internal crossovers (usually floor standing speakers) and may have a shorted or burnt board (usually very visible brown burn marks on the board) and can possibly be repaired if your handy with a soldering iron. Now, if you disconnect the speaker wire at the speaker and it still says "protect" Check your wire for the obvious cut or nail thru the wire if possible. If your system has wiring that runs behind walls, you may need to use your meter again. Disconnect the wire at both ends, keep the ends separated, put your meter on ohms resistance and touch probes to the + and - wires at one side. If the meter pegs to the right or reads "1...." the wire is shorted and needs to be replaced or repaired at the short. Hope this helps.
Posted on Jun 13, 2010
Tips for a great answer:
Jan 01, 2016 | Sony STR-K840P
Jan 01, 2011 | Sony STR-DB940 Receiver
Dec 05, 2010 | Sony STR-DB940 Receiver
May 29, 2010 | Sony STR-DB940 Receiver
Nov 02, 2009 | Sony STR-DB940 Receiver
Nov 02, 2009 | Sony STR-D965 Receiver
Sep 26, 2009 | Sony STR-DB940 Receiver
Oct 06, 2008 | Sony STR-DB940 Receiver
May 27, 2008 | Sony STR-DB940 Receiver
Aug 19, 2007 | Sony STR-DE545 Receiver
195 people viewed this question
Usually answered in minutes!