Question about Jet 3 Ultra Power Chair

1 Answer

Turn it on. it beeps, all the lights turn on for a second then go out. the horn works.not the chair.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Jet Master
  • 401 Answers

Unplug the charger. Make sure your battery is good. Strege Mobility

I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Posted on Oct 10, 2017

Ad

2 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: All six lights blink on my Jet 3

I just had the same problem with my uncle's power chair. The number of "blinks" indicates a problem code to the technicians. My chair needed the joystick control assembly replaced. Once replaced, evrything was back to normal. 'Not a cheap fix but much needed. Good luck my friend!!

Posted on May 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lights flashing when turned on, replaced batteries,fuse, in drive position


the amount of flashing lights will give you a Flash code. If the the lights are going up and down, you may have a locked joystick. one method is to turn on and (within 10 sec.) push the horn button twice. Push the power button then push the joystick forward until there is a beep sound then back until you hear a beep sound to unlock.

I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Mar 30, 2016 | Pride Go Chair Power Chair

1 Answer

MY BATTERY INDICATOR LIGHT CONTINUSLY SCROLLS FROM LEFT TO RIGHT CHAIR WILL NOT MOVE


You are in locked mode. try turning the joystick on and pushing the horn twice. or if that did not work try turning the joystick on and pushing gimbal forward until it beeps and then back until it beeps. should be unlocked, scrolling up and down will stop and you can drive.

I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Jan 27, 2016 | Pride Jazzy Select Elite

1 Answer

THE BATTERY LIGHT CONTINUSLY SCROLLS FROM LEFT TO RIGHT AND CHAIR WILL NOT MOVE


Turn on Joystick and push horn twice, you are in locked mode. If this didn't work then turn Joystick on push gimbal forward until you hear a beep, then move the gimbal back until it beeps you are now unlocked. Gimbal= what you push to go left right forward or back on a joystick.

I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

Jan 27, 2016 | Pride Jazzy Select Elite

1 Answer

All lights flashing, won't stop, won't respond (although the horn beeps).


joystick is locked,press the horn twice in ten seconds and hope this helps u

Dec 20, 2013 | Pride Jazzy 1103 Ultra Standard Power...

1 Answer

The chair is locked. I had this happen a long time ago and I needed to move the joy stick diferent directions to get it unlocked but I do not remember how. It is a Jazzy 1113.


If it is the older VSI controller, turn on chair. as the battery lights scroll, hold the joystick in the (UP) position until you hear a beep. Then immediately place the joystick in the (down) position until you hear a beep. then place the joystick in center position, once you hear the beep for the final time, it should be unlocked.

If you have a Dynamic controller, turn on chair then press the horn button to unlock.

Sep 15, 2011 | Pride Jazzy 1113 ATS Indoor Power...

1 Answer

Is the horn on my jazzy power chair 12 or 24 volt? the horn is so weak that you can barely hear it and i would like to replace it with a roadrunner beep beep horn, but it is 12 volt. and the system on my...


Bob why don't you run a small 2 wire cable from one battery to the armrest where your joystick is located and attach the new horn and a small push button switch to the joystick bracket coming from under the armrest. loosen the knob tightening the joystick bar and pull it out enough for you to attach the horn and button to it. I 'm not sure if that will work because I don't know what the new horn looks like but you can also mount the horn under the shroud near the battery and run the wire to the switch at the joystick. Good luck sounds like an good project

Feb 27, 2011 | Pride Jazzy 1103 Ultra Standard Power...

1 Answer

Not sure witch jazzy chair i got but the joy stick blink and keeps blinking i have tried pushing horn button twice and also turning it on and pushing joy stick forward waiting for it to beep but no beep....


The jazzy probably has a VSI controller and if it is sleep mode then the lights will scroll rather than blink. Now turn on the chair and see if the blinks have a pause between them, ie 4 blinks pause 4 blinks pause etc If they do count the number of blinks and this will give you the error code ie 4 blinks right motor 3 blinks left motor your owners manual should have a chart listing the error codes If not you can contact Pride tech support @ 1-800-800-8586 ask for jazzy tech support

Hope this helps

Feb 17, 2011 | Pride Jazzy 1103 Ultra Standard Power...

1 Answer

Not sure witch jazzy chair i got but the joy stick blink and keeps blinking i have tried pushing horn button twice and also turning it on and pushing joy stick forward waiting for it to beep but no beep....


LOCKING/UNLOCKING THE VSI

The VSI has a feature that enables you to lock your power chair to prevent

unauthorized use.

To lock the VSI:

1. With the VSI powered on, press and hold the on/off key. After one (1)

second, the VSI should beep.

2. Release the on/off key.

3. Push the joystick to the full forward position until the VSI beeps.

4. Pull the joystick to the full rearward position until the VSI beeps.

5. Release the joystick. There should be a long beep.

6. The VSI is now locked.

To unlock the VSI:

1. Press the on/off key and power on the VSI. The maximum speed/profile
indicator should ripple side to side.

Good Luck
mimobility

Feb 17, 2011 | Pride Jazzy 1103 Ultra Standard Power...

1 Answer

All six lights blink on my Jet 3


I just had the same problem with my uncle's power chair. The number of "blinks" indicates a problem code to the technicians. My chair needed the joystick control assembly replaced. Once replaced, evrything was back to normal. 'Not a cheap fix but much needed. Good luck my friend!!

Apr 28, 2009 | Jet 3 Ultra Power Chair

Not finding what you are looking for?
Jet 3 Ultra Power Chair Logo

Related Topics:

303 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jet Health & Beauty Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Vincent G
Vincent G

Level 3 Expert

2361 Answers

ray gallant

Level 3 Expert

66464 Answers

Are you a Jet Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...