Question about Linksys Computers & Internet

Open Question

What's your question? i can't a cases internet connection thorough my Linksys wrt300n what can i do

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: configure WRT300N wireless Router to connect internet using PPPoE

Often the nets and subnets are NOT the same.. ie The Fixed connection often uses 192.168.0.1, 192.168.1.1, however sometimes the wifi is setup 10.1.1.1, or 10.0.0.1 etc, have you checked this? Esentially tho ya router is an "Acess Point" and ya Lappy etc is ya "Client" the links below has a lot of tutorials to help have a look. http://portforward.com/routers.htm http://portforward.com/guides.htm

Posted on Aug 05, 2007

Ad

Anonymous

  • 1 Answer

SOURCE: Linksys WRT300N router issue

I have the wrt300n router it was a little tough working with but it works great. I have 2 linksys cameras hooked up to it. when 1st hooking up have to up plug modem & router plower up router then modem lites should start flashing using wep or not should see routers name from other wireless computer in router.

Posted on Apr 20, 2009

dholaday

  • 226 Answers

SOURCE: Linksys WRT300n will only allow local access wirelessly

go into the router interface and see if it is set for DHCP and reboot systems it should be fine

If you need further help, reach me via phone at https://www.6ya.com/expert/david_eb7ea98642566cc6

Posted on Jul 21, 2009

kakee

Michael Galve

  • 1269 Answers

SOURCE: How do you connect the new PSP Go to Linksys

On the PSP make sure the WLAN Switch is turned on. To connect to your router, go to System Settings > Network Settings > Infrastructure Mode then select the Network that you want to connect. If it's Linksys, select Linksys and press X. Select Scan and choose the wireless network and Enter. If it asks you for network key, type your wireless network key and connect. That should do it.

Posted on Oct 06, 2009

govinda123

Prashant M

  • 2277 Answers

SOURCE: linksys wrt300N wireless light not blinking

the wireless connections says limited or no connectivity when it does not get IP address from the router.
There might be problem with the wireless settings of the router.
if your network is a secured network then you will need to check the network key.
You can try to upgrade the firmware of the router. that will be a good option.
Click Here for step by step solution

Posted on Oct 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to put a password on my router coz my neighbors try to connect everytime and the connection is very slow pls help me what will i do


Here's how you can put a password for your Linksys WRT300N Wireless Router

1. Open your browser (IE, Firefox, or Chrome)
2. Type 192.168.1.1
3. Type these credentials
•un: admin
•pw: admin
4. On the Linksys Homepage, click on the "Wireless" Tab on top.
5. Click on "Basic Wireless Settings" just underneath the "Wireless" Tab
6. Rename your Network Name (SSID) to your desired name.
6.1. Click Save Settings
7. Click on "Wireless Security" (on top, beside "basic wireless settings")
8. Change your security mode from "disabled" to "WEP2 Personal"
(sub options should appear after)
9. On the Pre-Shared Key box, type in the password that you want to create for your wireless network.
(make sure you write this down and keep a copy in case you forget your password)
10. Click Save Settings.

Your done. No more free internet for your neighbors.

Hope this helps.

teEMOgeek

Aug 10, 2011 | Linksys WRT300N Wireless Router

1 Answer

WRT300N: does not boot, all leds are lit


Solution 1.

How can I reset the Linksys WRT300N to factory defaults?
Hold the Reset button on the Linksys WRT300N for about 30 seconds.

What is the IP Address, Username and Password to log in to the WRT300N?
IP Address: 192.168.1.1
Username: none
Password: admin

You should also know the configuration of your ISP provider after reset. You'll need to re configure your connection from modem to router.

Solution 2

How do I upgrade the Firmware on the Linksys WRT300N?
# 192.168.1.1 -> Administration tab -> Firmware Upgrade sub-tab. Click "Browse" and browse to the firmware upgrade file on your computer. Click "Start to Upgrade". Do not reset or power cycle unit while it is upgrading.


What is the IP Address, Username and Password to log in to the WRT300N?
IP Address: 192.168.1.1
Username: none
Password: admin

Apr 10, 2011 | Linksys WRT300N Wireless Router

1 Answer

Linksys WRT300n will only allow local access wirelessly


go into the router interface and see if it is set for DHCP and reboot systems it should be fine

If you need further help, reach me via phone at https://www.6ya.com/expert/david_eb7ea98642566cc6

Jul 17, 2009 | Linksys WRT300N Wireless Router

1 Answer

How to put to secure my linksys wrt300n router?


First, you'll need to log into the Router, do this with a cable.
Second, you will need to enable WPA, if that doesn't work, use WEP. This is the support page for your Router:
http://www.linksysbycisco.com/US/en/support/WRT300N

Read the FAQ related to your internet connection type, read through it all. It will have links to setting up the wireless connection and wireless encryption.

This link is probably what you will eventually find yourself, but the above link starts you from the beginning of the process just in case something is not setup right.

You'll need to pick a long hard to guess password, use letters and numbers. Oh, and you'll also need to choose a password for the login of the Router itself. Once you choose your passwords, write them down and keep them with your router. Normally I tape the passwords to my Router. Just be sure not to cover any vent holes.

Mar 14, 2009 | Linksys WRT300N Wireless Router

1 Answer

WRT300N dosnt connect


if your connection (isp) is CABLE you will need to clone the mac of the main computer.

For cable connection verify what computer can go online with your modem, once you know the main pc connect it to port one, access the routers setup page by typing 192.169.1.1 then locate MAC ADDRESS CLONE in line with basic setup. enable it click the macclone button then save settings.
connect your modem to the internet port on the router, do a power cycle on the modem and router.
then check the status tab on the linksys setup page if you have numbers on the dns it should be online.


Sep 12, 2008 | Linksys WRT300N Wireless Router

1 Answer

Not Connecting On Wireless


make sure your modem is connected to the INTERNET PORT of the WRT300N. wired pc must have an ip address of 192.168.1.x so we can say that the internet is really coming from the wrt300n

Mar 08, 2008 | Linksys WRT300N Wireless Router

1 Answer

Support


Try these steps:

1. First of all connect your PC Directly with Modem & check if you're able to go online or not.

2. If No , then contact your ISP.

3. If yes ,Disconnect CAT5 cable coming out of Modem from PC & connect into WAN port (on rear panel you'll find it) of Linksys WRT300N Router , After that on rear panel you'll find small hole with a Reset button inside it. Use needle or pen to press it quiet hard for 1 minutes continuosly, This'll restore all default settings.

4. After that give static IP - 192.168.1.2 to your PC ,subnet mask 255.255.255.0 ,default gateway - 192.168.1.1 & connect your PC directly with a LAN port on the back side of Router.

5. After that type 192.168.1.1 in the address bar of your explorer & login window will come , type username = admin & leave password field blank, then you'll get Blue coloured Router configuration page, From this page you can configure your Router.

6.Now if your Internet connection is Cable then default setting will work for you, However for DSL connection ,on this page you'll find internet connection type - selectiondrop down box - select PPPoE into it for DSL connection.

7. After that restart your computer & you should be able to go online.

Jan 07, 2008 | Linksys WRT300N Wireless Router

2 Answers

Configure WRT300N wireless Router to connect internet using PPPoE


Often the nets and subnets are NOT the same.. ie The Fixed connection often uses 192.168.0.1, 192.168.1.1, however sometimes the wifi is setup 10.1.1.1, or 10.0.0.1 etc, have you checked this? Esentially tho ya router is an "Acess Point" and ya Lappy etc is ya "Client" the links below has a lot of tutorials to help have a look. http://portforward.com/routers.htm http://portforward.com/guides.htm

Aug 05, 2007 | Linksys WRT300N Wireless Router

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4367 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...