Question about Garden

1 Answer

Carb and governor parts rover lawn edger model no. 8106

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

  • Expert
  • 346 Answers

I would contact this dealer http://www.lawnflite.co.uk/lawnmowers/Rover-Lawnmowers

Posted on Oct 02, 2016

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Manual for rover lawn edger model 8106


Give these guys a ring http://www.lawnflite.co.uk/lawnmowers/Rover-Lawnmowers


They are a dealer in the UK


Best,

Joe

Oct 02, 2016 | Homelite Garden

1 Answer

Manual for rover lawn edger


Check this dealer out http://www.lawnflite.co.uk/lawnmowers/Rover-Lawnmowers

They can give you assistance.

Cheers,

Joe

Oct 02, 2016 | Garden

1 Answer

How to replace throttle spring on toro 16585


Your governor spring goes from the governor arm to the throttle shaft on the carb. hope this helps. Let me know if you need more help

Aug 09, 2014 | Toro Power Lawn Mower

1 Answer

Craftsman trimmer 25cc


Diaphrams can be tricky sometimes...seating can be irritating. If carb disassembled and cleaned out...might have to check adjustments. Make sure screw didn't get loose. I had one do that before when governor broke.

Apr 21, 2014 | Craftsman Convertible 25cc. Gas Line...

1 Answer

I have a craftsman tecumseh 4.5 hp mower throttle free type and i have cleaned and rebuilt the carb replaced the carb mounting gasket between the carb and intake and also replaced the o rings on the...


1ec7ba32-45ac-4b07-8389-f863014e42da.jpgIt still sounds like a carburation issue. Are you sure all jets, vents and ports in carb are open? Another possibility is that the governor setting is off. The governor is the rod that comes out of side of engine and connects to throttle linkage on carb. To set governor to factory setting, push governor linkage in direction that opens throttle valve, loosen screw on governor arm and turn rod in same direction until it stops, while holding in this position tighten screw on governor arm. This is called a static setting. If this doesn't work I would disassemble carb, remove all plastic and rubber parts and soak in carb dip overnight. Picture may be different from your unit but it shows governor linkage to carb. Good luck and happy wrenching!

I’m happy to assist further over the phone at https://www.6ya.com/expert/layne_0fccff498c319c32

Sep 18, 2013 | Garden

1 Answer

I have a briggs model 407777 that was idling up and down from near top range to bottom. Found some dust in the carb intake and decided to cliean the carb. When removing the manifold/ carb, I took loose...


These can be tricky, but your on the right track. With throttle set on high (engine off), turn governor linkage in the same direction that opens throttle valve in carb wide open, then turn the governor rod in that same direction then tighten bolt on governor arm. This is a static setting. The high and low idle is most likely a dirty carb so assuming the carb is now clean your idle should be better. Hope this helps. Good luck!

I’m happy to assist further over the phone at https://www.6ya.com/expert/layne_0fccff498c319c32

Aug 12, 2013 | Craftsman 20 hp 42 in. Deck Lawn Tractor -...

1 Answer

I have a craftman 4 cycle mini tiller, running to slow. need to run at a faster speed. do not where to adjust.


If the carb has the "fixed" throttle control. Find the governor control lever with the small, long coiled spring attatched to it in the middle. It may be hooked to a metal tab that is on the back carburetor bolt. Bend the tab to your left to increase set speed or to the right (towards governor lever) to decrease.

Sep 05, 2011 | Craftsman Gas Mini - Tiller/Edger

2 Answers

I mixed up one spring and the mower idles low on craftsman eager-1 5.0 22 inch cut


I think that model may use the Tecumseh engine and carburetor application. Here is a diagram of what your machine (carb/choke and governor) should look like.

http://www.angelfire.com/mb2/visitme/mower/tecumseh.html

May 14, 2011 | Craftsman Garden

1 Answer

Craftsman Trimmer/Edger 4.0 HP Engine races...


Most likely, the mechanical governor is damaged inside the engine. If you have tools, a sense of adventure, and lots patience, this can be replaced for a modest cost in parts.
If not, take it to a reputable repair shop.
The governor replacement involves engine removal, opening the crankcase, lots of parts-cleaning, and attentive reassembly.
Would be happy to help you if you decide to tackle this repair.
Hope this helps.

Oct 03, 2009 | Garden

Not finding what you are looking for?
Garden Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

roeb

Level 3 Expert

819 Answers

john h

Level 3 Expert

22486 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...