Question about GE Dishwashers

Open Question

My GE Prile dishwasher runs fine on normal cycle; speed cycle starts, display goes blank then acts like machine was reset (back on normal cycle, but won't actually run a speed cycle).

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
johnychel

isaac johny

  • 796 Answers

SOURCE: dishwasher not running

hello sir.....
is the Start/Resume indicator flashing?
Opening the door or interrupting the power stopped the cycle. Close the door and press START/RESUME.

Does the Start/Resume indicator flash 3 times when you
press START/RESUME? The dishwasher is waiting for you to
open the door after the last cycle. Open and close the door,
then press START/RESUME.

may be the motor has stopped due to an overload....as you have mentioned...many of the buttons were pressed...
The motor automatically resets itself within a few minutes. If it does not restart, call for service.

In Canada, call 1-800-807-6777, or your nearest designated
service center.
In USA ..Call the Whirlpool Customer eXperience Center
toll free: 1-800-253-1301.

If you need further assistance, you can write to us with any
questions or concerns at:
Customer Interaction Centre
Whirlpool Canada LP
1901 Minnesota Court
Mississauga, Ontario L5N 3A7

Posted on Feb 25, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: GE Nautilus dishwasher wont run

Thank you! Our dishwasher hasn't been working for so long. I've tried spinning the fan to get it unstuck a long time ago but I thought that wasn't the problem. The fan was stuck real tight and i couldn't turn it more than a quarter turn each time. This time it worked!

-Turned off power to dishwasher on circuit breaker
-Removed kick panel
-Used two screw drivers, one to turn the fan till I couldn't any more and the other one to hold the blades in place so that it wouldnt "unwind". Then I would turn the fan some more. It turned less and less each but after repeating about 5 times the fan got un-stuck.
-Turned the power back on to the dishwasher and turned the dishwasher back on and IT WORKS!

THANK YOU!!

Posted on Nov 09, 2008

ginko

Ginko

  • 19396 Answers

SOURCE: GE Profile PDW7880G00SS Dishwasher will not Start

Re: My dishwasher start light flashes and the timer display is blank.

That is a fault condition, if the display is blank it is probably a faulty control board.

Unplug the appliace from main, or trip circuit braker to cut power for ten minutes.

If display is still blank on startup, then replace the timer control assembly.

Posted on Mar 13, 2009

Anonymous

  • 1 Answer

SOURCE: ge triton xl dishwasher

One answer is NEVER buy another GE product!!! I bought all GE Profile appliances when I redecorated my kitchen. Have had issues with every single piece. Refrigerator has been replaced twice (on 3rd one). Triton XL dishwasher will not reset...good luck getting it back to normal wash if you change a cycle...for example to run just a rinse. It is almost impossible to get it to reset. And don't get me started on the over the stove microwave. Never have been able to use the lights. Every time from day one I turn them on, the bulbs blow and the cover shatters. Absolutely no support from GE!!!

Posted on Sep 08, 2009

ned_san_jose

Ned Halaweh

  • 239 Answers

SOURCE: I have a GE Profile Triton Dishwasher and it has

Hello, how are you?
It sounds like you have a stuck key on the keypad, preventing you to push any other key.

I've seen this problem many times in the past 4 years.

Good luck.
Ned

Posted on Sep 21, 2009

Testimonial: "Thank you so much...what should I expect this to cost me for parts and labor Ned? Should we just wait and buy a new dishwasher? A new one $248! "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a GE Profile Triton Dishwasher and it has worked fine for about 8 years. Suddenly it will not reset. The reset light blinks after reset but you can not choose a normal cycle afterwards. I shut of...


Hello, how are you?
It sounds like you have a stuck key on the keypad, preventing you to push any other key.

I've seen this problem many times in the past 4 years.

Good luck.
Ned

Sep 20, 2009 | GE 24 in. Profile PDW7800 Built-in...

3 Answers

GE WHDRR418 top load washer won't spin at high speed; the washer does the complete cycle, and agitates in both directions and does physically spin, but it will not go into the 'high speed' spin that...


we can eliminate the motor and the switch since that part is working. sound like your timer might be faulty, timer make everything work in persistence cycles, if its goes bad sometime it tend to jump/skip cycles.

Jul 21, 2009 | GE WSXH208A Front Load Washer

7 Answers

GE Profile PDW7880G00SS Dishwasher will not Start


Re: My dishwasher start light flashes and the timer display is blank.

That is a fault condition, if the display is blank it is probably a faulty control board.

Unplug the appliace from main, or trip circuit braker to cut power for ten minutes.

If display is still blank on startup, then replace the timer control assembly.

Mar 13, 2009 | GE 24 in. Profile PDW7880G Built-in...

4 Answers

GE Triton not working


Jitterbugclu-
I may have the solution. Husband just turned off power to dishwasher via circuit breaker. Waited around 30 minutes.
Restored power and Triton came back with normal lights.
I just ran a cycle and all was well. Hope this helps you.
My fingers are crossed because I don't know what happened but did read on another site that this should be the first thing you try before expen$ive repairman.
Reply back if it works!
TootieC

Dec 25, 2008 | GE 24 in. GSD6660GSS Built-in Dishwasher

1 Answer

PDW7880G-No power to control panel. Just stopped at the end of drain cycle


Solution Found!!

Checked for power to dishwasher. According to the manual, shutting off the breaker for more that 30 seconds resets the dishwasher. It did!!! The dishwasher works fine now. THANKS!!!

Feb 19, 2008 | GE 24 in. Profile PDW7880G Built-in...

3 Answers

Ge triton xl dishwasher


One answer is NEVER buy another GE product!!! I bought all GE Profile appliances when I redecorated my kitchen. Have had issues with every single piece. Refrigerator has been replaced twice (on 3rd one). Triton XL dishwasher will not reset...good luck getting it back to normal wash if you change a cycle...for example to run just a rinse. It is almost impossible to get it to reset. And don't get me started on the over the stove microwave. Never have been able to use the lights. Every time from day one I turn them on, the bulbs blow and the cover shatters. Absolutely no support from GE!!!

Dec 24, 2007 | GE 24 in. GSD6660GSS Built-in Dishwasher

1 Answer

GE Nautilus won't drain after Rinse Cycle


Check disposer plug. If a garbage disposer has been recently installed, it is possible the disposer drain plug was not removed. The drain plug is a plastic piece in the disposer that blocks the hole where the dishwasher hose connects. Also check the hose connected to the disposal. Mine apparently had a kink in it. When I straightened the hose the dishwasher drained at full speed (I recently had a plumber re-route a hot waterline. He must has bent the hose). Hope this helps. If not go to the GE website. That's where I found my answer.

Nov 03, 2007 | GE 25 in. Nautilus GSC3400J Free-standing...

11 Answers

Ge quiet power 3 dishwasher


According to the GE repairman who visited, the solution is to close the machine (with the lights flashing). The machine starts and goes through the cycles, which it does rapidly and then all the lights turn off and the machine becomes silent after 1-1/2 to 2 minutes. Then the machine has been reset to normal. During this reseting period nothing happens inside the machine, although you may hear a running sound.

Thus, the solution is to run the machine in this flashing light state for the 1-2 minutes it takes to go raipdly through each cycle and then reset.

I hope this helps.

Oct 09, 2007 | General Electric Adora GHDA670N Built-in...

2 Answers

GE Nautilus Dishwasher - NO water coming in at beginning


Normally,if water doesn't come in, cycle should not go on ! Add water by hand to tub and operate the dishwasher. Let us know with your results and we will see how could we assist you.

Aug 03, 2007 | GE 25 in. Nautilus GSC3400J Free-standing...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dishwashers Experts

Mike

Level 3 Expert

4363 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Vitally Alcher

Level 3 Expert

1645 Answers

Are you a GE Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...