Question about Sharp Aquos Televison & Video

Open Question

Have a sharpe aqueous LCD-60le830x giving one long blink on the white arrow in bottom centre of set will not reset

Posted by on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

sgrahamtx

  • 41 Answers

SOURCE: Sharp Aqueous 37" LCD TV

From the information you have provided failed capacitors in the power supply is likely causing the problem. The safety circuitry shuts the TV set down when it detects a problem. This model of TV has over 2,000 parts which include millions of transistors inside the integrated circuits. The capacitors will change value, leak and become defective. Resistors will change value and burn. Integrated circuits and transistors can go bad. This can cause other components to become defective, which can have a domino effect and cause other parts to fail. Replacing one defective part may make the TV operate for a short time but the part will fail again since if the parts that caused the failure to begin with are not replaced. The only way to know for sure what is causing the problem, which parts that are no longer within factory specs and for proper repair all the electronics must be diagnosed by someone with the correct electronic test equipment and the skills to use the test equipment. The repair should cost about $250 if carried into a TV repair shop. A small TV repair shop will often charge less than a large repair facility.

Posted on Feb 25, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sharp TV lc-60le640u



Unplug set, press and hold (on set) volume-down and channel-down and hold them while plugging in set. Will come on with "k" on screen, or will crash again if backlight bad. If it stays on, use your remote and arrow right then look for "fact init" and any other reset and turn them on. Arrow back up to "fact init" and hit enter. Let set recycle to green and unplug/re-plug in 5 seconds: the set should be in OOB state'

Dec 05, 2017 | Sharp Televison & Video

1 Answer

Sharp TV model lc-60le640u



Unplug set, press and hold (on set) volume-down and channel-down and hold them while pluging in set. Will come on with "k" on screen, or will crash again if backlight bad. If it stays on, use your remote and arrow right then look for "fact init" and any other reset and turn them on. Arrow back up to "fact init" and hit enter. Let set recycle to green and unplug/re-plug in 5 seconds: the set should be in OOB state'

Dec 05, 2017 | Sharp Televison & Video

1 Answer

Turn the tv on and the green light blinks and then turns off and comes back on then turns off again but the screen is black. What is wrong?


KDF 60XS955 intermittently turns off green light blinking then on after...
The frequency and color of the blinks will indicate the issue. There is a hold-down button sequence to try to backdoor your way into the set to see if the panel will light. You may have simply racked up too many "weird tuner faults" and need to reset it. My suspicion is that it's either that or bad panel backlight.

Unplug set, press and hold (on set) volume-down and channel-down and hold them while pluging in set. Will come on with "k" on screen, or will crash again if backlight bad. If it stays on, use your remote and arrow right then look for "fact init" and any other reset and turn them on. Arrow back up to "fact init" and hit enter. Let set recycle to green and unplug/re-plug in 5 seconds: the set should be in OOB state
ref:
Sharp lcd tv power button flashing

Feb 13, 2016 | Televison & Video

1 Answer

Power and opc bottom blinking, tv won't come on


Sharp LED/LCD EEP cleared Step 1 Remove Mains Plug 2 Press On/Off Switch from LED/LCD Panel 3 Press Ch Down & Input Switch together and plug in mains cord 4 LED/LCD will start 5 "K" will appier on Screen 6 Press Ch Down & Vol Down from LED/LED Panel 7 1/9 Page will appier on Screen 8 Go to 9/10 page by pressing Up & Down arrow of remote 9 Select EEP Cleared 10 Press ok button from remote 11 On Screen dispay EEP running 12 Remove Mains Plug after complete EEP Run 13 Restart LED/LCD

Jan 08, 2016 | Sharp Televison & Video

1 Answer

I have a LCD-60LE640U sharp Aquos TV. There is no power and the white arrow blinks twice. 1st arrow blinks 1 sec and 2nd arrow blinks 1/2 sec. Any solutions?


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/
Blinking codes details to many popular brand TVs are given. Surf the site with patience.
If blinks continue without any pause, the main board is faulty.

Jun 25, 2015 | Sharp LC Televison & Video

1 Answer

My aqueous 50 inch tv has white lines all over. You can see the picture but just barely through the lines! How do I fix it?


If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Line, faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent.

Oct 15, 2014 | Sharp Aquos Televison & Video

1 Answer

Sharp Aquos TV doesn't work, power light is blinking at 1 blink/sec


Sounds like a fault code, ~I have found some info on it:-

The frequency and color of the blinks will indicate the issue. There is a hold-down button sequence to try to backdoor your way into the set to see if the panel will light. You may have simply racked up too many "weird tuner faults" and need to reset it. My suspicion is that it's either that or bad panel backlight.

Unplug set, press and hold (on set) volume-down and channel-down and hold them while pluging in set. Will come on with "k" on screen, or will crash again if backlight bad. If it stays on, use your remote and arrow right then look for "fact init" and any other reset and turn them on. Arrow back up to "fact init" and hit enter. Let set recycle to green and unplug/re-plug in 5 seconds: the set should be in OOB state.

hope it helps

Aug 23, 2014 | Sharp Aquos Televison & Video

1 Answer

I recently changed the bulb in the projector with a new bulb but after changing it it now says the bulb is at 0 % and no longer works. Is there a reset button we may have missed when changing the bulb?


to reset the lamp hours,
simultaneously press down the bottom right MENU/HELP button, and the centre ENTER button and the centre bottom DOWN ARROW button.
Then with a spare finger press the top left STANDBY/ON button.
LAMP 0000H should be displayed. it is now reset

Feb 28, 2011 | Sharp PG-MB56X DLP Projector

1 Answer

Hook up Avertec 3200 to Sharp Aqueous TV


After I found the manual somewhere on the internet, I realized that it is already available here. (Lucky you!)

I could not find a specific manual for your Aquos TV (which model?). Look into your manual, and see if there is an option to connect via VGA of HDMI for video
If you want to use your TV speakers, it depends what audio input options you have on your TV. You might need a cable like this:

4dfae91.jpg

The red/white connectors into your TV, the 2.5mm plug into your computer.

Jan 11, 2009 | Averatec 3200 Notebook

1 Answer

Sharp Aqueous 37" LCD TV


From the information you have provided failed capacitors in the power supply is likely causing the problem. The safety circuitry shuts the TV set down when it detects a problem. This model of TV has over 2,000 parts which include millions of transistors inside the integrated circuits. The capacitors will change value, leak and become defective. Resistors will change value and burn. Integrated circuits and transistors can go bad. This can cause other components to become defective, which can have a domino effect and cause other parts to fail. Replacing one defective part may make the TV operate for a short time but the part will fail again since if the parts that caused the failure to begin with are not replaced. The only way to know for sure what is causing the problem, which parts that are no longer within factory specs and for proper repair all the electronics must be diagnosed by someone with the correct electronic test equipment and the skills to use the test equipment. The repair should cost about $250 if carried into a TV repair shop. A small TV repair shop will often charge less than a large repair facility.

Apr 08, 2008 | Sharp Aquos LC-37GD6U 37 in. LCD HDTV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76171 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Sharp Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...