Question about HP Boating

Open Question

Minkota 3 hp trolling motor. - HP Boating

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Johnny G14

  • 8 Answers

SOURCE: my brother inlaw got a minkota 40ta all terraine

I would check the battery. If you're using an old or under charged battery you will loose power for sure. Make sure you're also using a 12v deep cycle marine battery as this will ensure proper operation and a longer battery life.

Posted on Sep 07, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 LUND TROLLING MOTOR PLUG WIRING 3 WIRES ON PLUG 2 WIRES ON TROLLING MOTOR CORRECT WAY TO HOOK UP


What is the voltage of the trolling motor (2 wire) (12V, 24V,36V?)you are trying to attach to the boat(3 wire). Please fill in more info and reply/repost to me. This is not a hard one!!
Thanks

May 26, 2017 | Boating

2 Answers

Lookinf for a manual for a minn kota model 55d


call 800 number for minn kota on your motor. they are very helpful and will fax or emial you a manual for the motor. good luck.

May 28, 2010 | Minn Kota Maxxum 55 Freshwater Bow Mount...

1 Answer

Why does the switch keep burning out?


call the 800 number on the motor for min kota they are great about ansering these questions. the first thought for me is that things are heating up due to too much amperage being drawn by the motor or a loose connection.you will needs to check the specs on that motor to tell and need to know what normal readings are which minkota will gladly supply you.

May 17, 2010 | Minn Kota Endura 30 Freshwater Transom...

1 Answer

Riptide RT65 24 volt with auto pilot goes nuts.


your magneto is shorting [ arcing on high needs, openup and replace magneto. call minkota and order a new magneto for your model, unless under warrantee.

Apr 13, 2010 | Minn Kota Riptide Sp Saltwater 70 Bow...

1 Answer

Hard foot pedal


On the base of the foot pedal there is a tensioner for the cable. Try loosening or tightening that first. If you still have the manual from when you bought it, it is explained in deatil in there. It's a common issue - not to worry!

Jul 28, 2009 | Minn Kota Maxxum 70 Freshwater Bow Mount...

2 Answers

MinnKota Endura 50 Runs only in high speed in forward and reverse


the coil pack is likely bad especially since you changed the switch. call minkota and get the bench tast info (very simple) and then order and replace the coil pack about 26 dollars. be very careful how you put the magnet assembly back together and mark the position of the case on the outside before disassembly. order a new seal kit and use locktite on the shaft again when reassemling to seal the shaft tube for water. dont run motor uout of the water much as it uses the water to cool the shaft and you can damage the seals. good luck.

Jun 18, 2009 | Minn Kota Endura 30 Freshwater Transom...

2 Answers

Bow mount 80lb to transom mount


Parts can be purchased from this dealer...There are schematics on the site for review....
http://www.northlandmarine.com/MinnKotaQuickRef.htm

May 06, 2009 | Minn Kota Riptide St Saltwater 80 Bow...

1 Answer

My brother inlaw got a minkota 40ta all terraine trolling motor that is supposed to produce 40 pounds of thrust. it does not seem to produce even close to that. is it possible that the motor is turning the...


I would check the battery. If you're using an old or under charged battery you will loose power for sure. Make sure you're also using a 12v deep cycle marine battery as this will ensure proper operation and a longer battery life.

Apr 18, 2009 | Minn Kota Edge 40 Freshwater Bow Mount...

2 Answers

Diagram of 36 volt hookup for trolling motor, i have a factory 24 volt wiring in my boat and I need to turn it into a 36 volt please help thank you


To get 36 volts, number batteries 1 thru 3. connect pos 2 to neg 1, connect pos 3 to neg 2, connect pos 1 to trolling motor controller and neg 3 to ground on trolling motor.
This is only a solution for 3 battery system.
For 4 battery system, connect 4 to 3 pos to pos and neg to neg.
budman772357@embarqmail.com

Mar 01, 2009 | Minn Kota Boating

1 Answer

The plastic part in my bow mount Turbo 765MX(36lb.thrust) Minkota


Hello poorjohn, stroll to www.minnkotamotors.com/index.asp When you call ask for ext #406 and ask for Dave. Refer to my logon 'themoneypitt' He is a great guy. Merry Christmas.

Nov 21, 2008 | Minn Kota Maxxum 70 Freshwater Bow Mount...

Not finding what you are looking for?
Boating Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Boating Experts

vince

Level 3 Expert

1234 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Douglas Thorburn

Level 2 Expert

36 Answers

Are you a HP Boating Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...