Question about Kenmore 24032\24036 Top Load Washer

1 Answer

Describe your Kenmore 24032 \ 24036 Top Load

Describe your Kenmore 24032 24036 Top Load Washer Problem When the machine goes to discharge the rinse water while spinning water leaks out of somewhere onto the floor. How do I diassemble the unit to further troubleshoot?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 90 Answers

MAke sure that the cothes are not unbalancing the tub. Iv seen this happen where the clothes are unbalancing the tub and it moving around and the when the water for the rinse is coming out its not getting in the tub its splashing on the top of the tub ring due the the unbalanced spin. does this happen when you wash a heavy load? do you notice it not doing that when you washer a light load?

Posted on Jul 26, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore top load washer 29822800 - washer-selector is set on one rinse- when machine starts the agitator starts immediately as water fills - then when machine stops after spin cycle in off position water...


if you are saying that the washer finishes the load of clothes and timer goes to off and water is filling the tub after this then you have a bad water valve on the back of the washer.disconnect the water lines and change out the valve

Aug 14, 2010 | Kenmore 24032\24036 Top Load Washer

2 Answers

Kenmore Oasis HE 27082 Front Load Washer


ohm the release solenoid. could be shorted or open. check for voltage to the circuit

Sep 22, 2008 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Describe your Kenmore 24032 \ 24036 Top Load


That is a bad water valve. Try my washer PICTORIAL for directions on replacing that water valve. NOTE: this is a pictorial of how to replace your drive coupling but you need to bust this ****** loose to get to that valve.

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Jul 06, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Describe your Kenmore 24032 \ 24036 Top Load


Hi, Make sure the washer is solid to the floor. To level the washer, Put your foot against the front panel at the floor and tip the back of the washer toward you. Then set the washer back down and the rear legs should self adjust.
Hopefully this will stop the washer from shaking.

Vic

Jun 30, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Describe your Kenmore 24032 \ 24036 Top Load


Water pump is my first guess. Did you check the hoses that hook to it? The pump is in the front of unit. Give full model number to further assist you.

Jun 15, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 22622100 Top Load Washer won't drain the water, nor rinse


HI!!! you seem to have a bad lid switch on your washer..I would also check the timer on it good lucck.

Feb 13, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore washer overflows during rinse cycle.


SOME OF THESE MACHINES HAVE TWO PRESSURE SWITCHES IN THEM, ONE FOR THE MAIN WASH WATER LEVEL AND ONE FOR THE RINSE WATER LEVEL. CHECK FOR A PLUGGED AIR PRESSURE HOSE FIRST AND THEN CHECK THE PRESSURE SWITCHES.

Jan 27, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore washer series 80, Clothes still soapy


If you are getting no water spray during the rinse cycle that would cause the soapy clothes issue.

Are you getting cold water during the wash/rinse cycles? If you have the machine set to warm/warm you may only be getting hot water while the final spin is calling for cold.

If you have cold water available then the timer is not calling for the water spray. The problem is either in the mixing valve or the timer.

Jan 10, 2009 | Kenmore 23822 Top Load Washer

1 Answer

No cold rinse


check to see that the hot and cold pipes are not crossed over
ie the hot pipe is on the cold tap
when machine goes into rinse cycle it only uses cold water

Nov 09, 2007 | Kenmore 15864/15862 Top Load Washer

2 Answers

No rinse


Make sure that you have both, hot and cold water connected and turned on. Some models will not advance through rinse if one of the hot or cold is off. See if this solves the problem, Catriver.

Jul 21, 2006 | Kenmore 80754 Top Load Stacked Washer /...

Not finding what you are looking for?
Kenmore 24032\24036 Top Load Washer Logo

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

fordexpert

Level 3 Expert

5692 Answers

Harvey Mahal

Level 2 Expert

39 Answers

Kristen Denison
Kristen Denison

Level 1 Expert

13 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...