Question about Linksys Computers & Internet

Open Question

Does the linksys cable modem model # cm3024 have a wps button?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 113 Answers

SOURCE: need to connect my old Linksys modem to a new Motorola SBV5121 cable modem.

THE MAIN LINE GOES INTO THE WAN PORT FROM THE MODEM PROVIDED FROM YOUR MOTOROLA .....THEN THE 4 PORTS ARE TO CONNECT THE COMPUTER ....HAVE FUN

Posted on Jun 02, 2009

Ad

Anonymous

  • 2 Answers

SOURCE: Switched from DSL modem to Cable modem. Linksys

If you had your linksys router controlling the DSL connection, it was most likely a PPPoe connection requiring a username and password. Most cable companies have dynamic IP address and do not require a username or password.

Open your internet browser, IE, Firefox etc and go to 192.168.1.1 >
Enter your router username and password, typically admin and admin

In the setup tab, change your connection FROM whatever is listed there and make sure it is Autumatic DHCP Save your settings, and restart the router.

You should be fine.

Posted on Oct 28, 2009

Michael Charney

  • 18 Answers

SOURCE: where is WPS PIN or

The WPS PIN is usually on a sticker on the bottom or side of the router. It will be all numbers, 4 to 6 digits usually, and haveno letters in it.

Hope that helps.

Posted on May 20, 2011

SOURCE: Does the linksys-G support WPS or AOSS?

Good question, I have the same router & Brother HL-2280DW and ran the printer setup CD from Windows XP SP3 via temporary USB connection & it seemed to work. The WAN report on the printer itself says OK, however the computer can't seem to find the printer "No devices could be found on the network." I let setup make changes to Windows Firewall, not sure about Microsoft Security Essentials however. This seems like a nice printer/copier at a nice price but this setup is frustrating! PS If it's a security issue I'd like to say thanks to all the hackers for ruining technology for everyone, your junk is responsible for slowing down & complicating computers & technology in the world. Someone please do everyone a favor & start making antibodies that *kill* viruses & spyware & spam and clean & speed things up for a change! All these villians - Where are the cyber super heroes????

Posted on Feb 25, 2012

TechyDrood

Justin

  • 2072 Answers

SOURCE: where is the wps button on a linksys router

Depends on the on router. The button should have a picture of an antenna on it or say WPS. Pres it and the light will flash then press the wps feature button on the device you are connecting. If this is a Linksys EX0000 model it should be on front and center on the top of the router.

Posted on Nov 24, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WPS light not working after pressing WPS button


Both sides of the connection need to be set up for WPS. A pin has to be set up.
I recommend using WEP until you figure out WPS.

Mar 21, 2014 | Zyxel Computers & Internet

1 Answer

Where is the WPS button on linksys wireless-N router


you need to look at the back of your router you will able to see a blue color button . this button is known as wps button .

Dec 30, 2013 | Linksys Wireless-N WRT150N Router

1 Answer

Where is the was button


I'm guessing you mean the WPS button - "Wireless Protected Setup" - As far as I can see from the User Guide this router doesn't have an actual WPS Button - You need to log onto its admin web interface and browse to the WPS setup page - Press the WPS button on your client device (laptop, printer, etc) then Click the WPS button in the router's web interface and let them talk to each other to establish a secure connection - The WPS light on the Front Panel should then light up when connected - You can find a user guide at the following url:
http://downloads.linksys.com/downloads/userguide/1224642967100/WRT54G2-EU_V10_UG_combination_NC-WEB.pdf

Jun 14, 2013 | Linksys WRT54G2 V1 Wireless-G BROADBAND...

1 Answer

Where is the Linksys E1000 wireless router wps button


You can download the manual from this WEB site.
http://help.ecobee.com/attachments/token/howroilplaxny3u/?name=Linksys+E1000_V10_UG_USA_NC-WEB.pdf

Apr 11, 2013 | Linksys Wireless-N WRT150N Router

1 Answer

Every so often, my internet seems to crash. On my pc it has a yellow caution sign over the internet. The data send/receive lights on my modem flash but the others don't when this happens. I try un


If it works sometimes ? when you unplug it then replugging it back in something is wrong with the modem / router or they might need to be reset .
or firmware upgrade
Reset linksy router b> One of the most common fixes for Internet connectivity often involves resetting the source of your Internet connection. If you have a DSL or cable Internet connection, you may use a Linksys router to get on the Internet. When you reset a Linksys router, you'll likely solve your connection problem.

Turn off the power to your computer's modem. Use the switch on your cable or DSL modem to disable it while you reset the Linksys router. Find the reset button your Linksys router. Most Linksys models have the reset option on the back of the router. Use a pointed pen or pencil to press in the reset button on your Linksys router. Hold down the reset button for approximately 30 seconds. Watch the lights on the front of the router. After you reset the router, power will get restored to the Linksys router. Once power's available, you can switch the modem back on. Reconfigure your router. After you reset your router, you'll have to log in and reconfigure your settings. The login name is typically left empty with your password as "admin."
Reset a Linksys Wireless Router b> You may need to reset your Linksys wireless router if you are having Internet connectivity issues or other networking problems. You can reset the router to the default factory settings, such as the default IP (Internet protocol) address, username and password. However, after you perform the factory reset, you can follow the initial setup instructions to replace your previous settings.

Write down any important settings you may have--such as the router's password--before you reset the router. Locate the reset button on the router. Some Linksys models have a reset button on the back side. Other Linksys models have a small pinhole you may need to access by using the tip of a pen or pencil. Press and hold the reset button for a minimum of 30 seconds to perform a factory reset on the Linksys router. The Linksys router should lose power. Power on the Linksys router to initiate the configuration wizard. Reconfigure any previous wireless settings on your Linksys router.

Hope this helps.
b>

Dec 28, 2012 | Computers & Internet

1 Answer

Where is the wps button on a linksys router


Depends on the on router. The button should have a picture of an antenna on it or say WPS. Pres it and the light will flash then press the wps feature button on the device you are connecting. If this is a Linksys EX0000 model it should be on front and center on the top of the router.

Nov 23, 2012 | Linksys 2.4 GHz 802.11b Wireless - B...

2 Answers

I've forgotten my security password for the wireless and want to allow another computer access. as i'm not very technical is it difficult to reset andstart again?i don't want to be without the...


If you have forgotten your LinkSys router password, the easiest thing to do is to reset your router to the factory default settings.
To restore the router configuration to factory defaults, hold the reset button on the unit for 30 seconds.
Once your router is hard reset, you will need to login and configure it again.
To reconfigure your LinkSys, connect a PC to one of it'sEthernet ports, load a web browser, and go to the URLhttp://192.168.1.1/. This will take you to a popup box which asks you to enter a username and password to login to your router.
LinkSys Default Password
On older LinkSys routers, the default username is blank and the default password is "admin." While newer models, both the default username and the default password are set to "admin."
Once you go past the login screen, you should be able to reconfigure the LinkSys router.
Here are some of LinkSys Router models along with its Default usernames:

Linksys EtherFast Cable/DSL Ethernet routers: Administrator
Linksys WRT54G, BEFW11S4: admin
Linksys Comcast routers: comcast
All other Linksys routers: {none}
Here are some of LinkSys Router models along with its Default passwords:
Linksys Comcast routers: 1234
Linksys BEFW11S4: {none}
All other Linksys routers: admin
For those [none] username/password entries listed above, no name or password is required. Just skip or press the Enter/Return key when prompted for those settings.

Jul 18, 2011 | Zyxel (91-004-361002) Wireless Router

1 Answer

Does my WRT160N have a WPS button and if so, where is it?


The Linksys WRT160N has WPS (Wi-Fi Protected Setup). If you are using WPA-PSK encryption (recommended), then you can easily connect the C4780 to your wireless network using WPS:


1) On the Linksys router, press the WPS button that is top of the case just under the Cisco label. When the LED on the button starts to blink, then the WPS process has started.


giles102.png

Jul 06, 2011 | Linksys WRT160N Wireless Router

2 Answers

Where and what is the PBC button on the wireless linksys router?


Push Button Configuration (PBC)

NOTE: The PBC method is to be used if the wireless client device (device that you are using to connect to the network) has a WPS button (either an actual one or a virtual one).

Step 1:
Click or press the WPS button on the client device.

Step 2:
Click the WPS button on the Linksys device. A pop-up window from the Wireless > Basic Wireless Security tab of the Linksys device will appear. This window will indicate the progress of WPS client configuration.

Dec 31, 2010 | Computers & Internet

2 Answers

Cannot connect to internet Model WRT54GS


Hi

I would like to know who is your internet service provider and would like to check if the router is configured with your ISP modem.
To configure for different ISPs here is the link
http://www.linksys.com/servlet/Satellite?c=L_CASupport_C2&childpagename=US/Layout&cid=1166859761879&pagename=Linksys/Common/VisitorWrapper&lid=6187977881B11
The links are there for setting up with DSL as well as cable modem. Do let me know if its working or not.
Thank you
Rakesh

Jan 06, 2009 | Linksys Wireless-G Broadband Router

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4367 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...